Hemisphere GPS Outback GUIDANCE AutoMate 750-3007 Bedienungsanleitung

March 2008 876-0105 Rev B1

AutoMate

Equipment Specific Installation Kit

P/N: 750-3007

Fits Spra-Coupe 3000/4000 Series Sprayers

Overview

A series of equipment-specific kits have been developed to allow the interface of

the AutoMate system with your product rate controller. This kit contains the

necessary components and instructions to connect AutoMate with the equipment

models listed above. Please read this manual thoroughly before beginning the

installation.

Kit Contents:

Unpack the installation kit and identify the required parts as shown.

REF ITEM QTY COMMENTS PHOTOGRAPH

A Interface Cable 1 Spra-Coupe

3000/4000

B 5-Channel

Driver 1

C Spade Covers 10 Not Shown

D Tie Straps 6 Black, 13 inch Not Shown

E Installation

Instructions 1 Not Shown

- 2 -

Installation:

Install the AutoMate interface onto the sprayer with the following steps.

1. Remove the four screws securing

the boom switch control panel on

the right console in the sprayer

cab.

Fig. 1: Boom switch control panel

2. Raise the boom switch panel and

locate the four connections for

each switch.

Each boom switch will have two

signal wires (yellow), a ground

(white), and a power (orange).

One of the signal wires will have

an additional wire piggy-backed

onto the same spade connection.

This is the positive boom signal

connection.

Fig. 2: Boom switch wiring

Screws

Positive Signal

Wire

Ground

Boom Switch 1

Negative Signal

Wire

- 3 -

3. Route the two small ends (wires

w/ spade connectors) of the

interface cable (A) from the floor

up through the console to the

switch panel.

The bundle of wires with male

spades is for connection with

existing Spra-Coupe signal wires.

The smaller bundle of wires with

female spades is for connection

with the Spra-Coupe boom switch

terminals.

Fig. 3: Interface cable routing

4. Disconnect the positive and

negative boom signal wires from

boom switch 1. Connect the signal

wires to the two corresponding

wires of the interface cable (A),

according to the table below.

Note: After connecting the

interface cable to the positive

signal wire, be sure to wrap the

electrical connectors with

electrical tape.

5. Disconnect the white ground wire

from the boom switch. The system

will now be grounded through the

AutoMate interface.

NOTE

: After detaching the

ground (white) wire, be sure to

wrap black electrical tape on the

tip of the female connectors.

Fig. 4: Boom 1 signal wire connection

Positive Signal

Wire

Negative Signal

Wire

Interface Cable

(A)

- 4 -

3-Boom System

Boom

Number

AutoMate

Wire

Color Connector

Shielding

Spra-Coupe

Wire

Number

1+ Black Un-Shielded 505B

1- Gray Shielded 506B

2+ Brown Un-Shielded 507B

2- Yellow Shielded 508B

3+ Blue Un-Shielded 509B

3- Orange Shielded 510B

Blk/Wht Un-Shielded N/C

Purple Shielded N/C

Brn/Wht Un-Shielded N/C

Green Shielded N/C

5-Boom System

Boom

Number

AutoMate

Wire

Color Connector

Shielding

Spra-Coupe

Wire

Number

1+ Black Un-Shielded 503B

1- Gray Shielded 504B

2+ Brown Un-Shielded 505B

2- Yellow Shielded 506B

3+ Blue Un-Shielded 507B

3- Orange Shielded 508B

4+ Blk/Wht Un-Shielded 509B

4- Purple Shielded 510B

5+ Brn/Wht Un-Shielded 511B

5- Green Shielded 512B

- 5 -

6. Connect the AutoMate boom 1

switch wire to the positive signal

terminal of the Spra-Coupe boom

1 switch. Refer to the table below

for the appropriate wiring code.

Fig. 5: AutoMate switch wire

AutoMate Switch Wire Connection

AutoMate

Wire

Color

Boom

Number 3-

Boom

System

Boom Number

5-Boom

System

Black 1 1

Brown 2 2

Blue 3 3

Blk/Wht N/C 4

Brn/Wht N/C 5

7. Repeat steps 4 - 6 for the

remaining boom

sections/switches.

Note: If you have 5 boom switches,

remove the spade covers on the

Automate wiring harnass (A)

before connecting them to the

signal wires.

Fig. 5: Boom switch wiring complete

AutoMate

Switch Wire

AutoMate

Switch Wires

Spra-Coupe

Signal Wire

Connections

- 6 -

8. Use the provided spade covers

to insulate the two blank

terminals on every boom switch.

Fig. 6: Boom Switch Connectors

Insulated

9. Connect the AutoMate interface

cable (A) to the 5-channel driver

(B).

10.Find a suitable mounting location

for the 5-channel driver and

install securely using screws or

tie-straps.

Fig. 7: 5-Channel driver install

11. Locate the joystick wiring

harness at the bottom front area

of the cab console. The end of

this harness will branch into

several packard connections.

Identify the two pin packard

connector which carries the

master spray/hold connection.

This connection will typically

have one blue and one white

wire entering and two yellow

wires exiting. Fig. 8: Master spray/hold connection

Switch Connectors

- 7 -

12.Disconnect the master

spray/hold connection and insert

the tee connector from the

AutoMate interface cable

Fig. 9: Master spray/hold tee

inserted

13.Locate the ground terminal

under the Spra-Coupe dash and

connect the two white ground

wires from the AutoMate

interface cable.

14.Connect red power wires from

the AutoMate interface cable to a

secure source of switched

power. Fig. 10: Ground wires connected

15.Connect the Power and Control

connectors of the Interface

Cable (A) to the AutoMate

console.

16.Secure all wiring with tie-straps

and clean up the installation.

Fig. 11: AutoMate console

17.In order for AutoMate to have

control of the boom sections the

rate controller Master Switch

must be in the ON position and

all individual boom switches

must be OFF.

Important: If the conditions of

step 16 are met, AutoMate will

begin to spray if 1) AutoMate

recognizes that it is in an un-

applied area and 2) AutoMate

recognizes a positive ground

speed.

Negative Signal

Wire

Inhaltsverzeichnis

Andere Hemisphere GPS GPS Handbücher

Hemisphere GPS

Hemisphere GPS eDriveTC Bedienungsanleitung

Hemisphere GPS

Hemisphere GPS LiteStar II Air Bedienungsanleitung

Hemisphere GPS

Hemisphere GPS LiteStar II Air Bedienungsanleitung

Hemisphere GPS

Hemisphere GPS V104s Bedienungsanleitung

Hemisphere GPS

Hemisphere GPS XF2 Bedienungsanleitung

Hemisphere GPS

Hemisphere GPS MBX-4 Bedienungsanleitung

Hemisphere GPS

Hemisphere GPS XF2 Bedienungsanleitung

Beliebte GPS Handbücher anderer Marken

Hama

Hama 53118 Bedienungsanleitung

Garmin

Garmin SOUNDER 125 Bedienungsanleitung

Garmin

Garmin DEZL 580 Bedienungsanleitung

Jigabot

Jigabot EX Bedienungsanleitung

Pointer

Pointer Cellocator CelloTrack XT LTE Installationsanleitung

Queclink

Queclink GV55LITE Bedienungsanleitung

Voxson

Voxson Voxtrack GPS500 Gebrauchsanweisung

Garmin

Garmin ECHOMAP PLUS Bedienungsanleitung

Starcom Systems

Starcom Systems Kylos Compact Bedienungsanleitung

Garmin

Garmin 15 H Series Bedienungsanleitung

Cobra

Cobra Marine MC 600Ci Bedienungsanleitung

Cellocator

Cellocator CelloTrack T Bedienungsanleitung

Enfora

Enfora Mini-MT GSM2228UG001 Bedienungsanleitung

Magellan

Magellan eXplorist 100 Bedienungsanleitung

Garmin

Garmin DEZL OTR500 Bedienungsanleitung

LTE

LTE G50B Bedienungsanleitung

SkyGolf

SkyGolf SkyCaddie SG1 Bedienungsanleitung

Garmin

Garmin GPSMAP 78 series Bedienungsanleitung