Hi-Spec Xcel 1250 Montageanleitung

Third Edition – Draft 3 – 19-12-2005
Manufacturers of
Agricultural Machinery
Hi-Spec Xcel 1250
Operator Instruction Manual
Hi-Spec Engineering Ltd.
Station Rd.,
Bagenalstown,
Co. Carlow, Ireland
Tel: - 059 9721929 Fax:-059 9721980

Hi-Spec Xcel 1250 Operators Manual
Hi-Spec Engineering reserves the right to make changes or improvements at any time without incurring any obligation to
make such changes on products sold previously.
2
Parts are subject to change at any time, without prior or direct notice to the customer. The
contents of this manual can as well be changed without prior notice. For information about
adjustment, maintenance or repair, which are not mentioned in this manual, you are advised to
consult the technical support of your supplier.
This manual has been made with all possible effort, but Hi-Spec Engineering and its suppliers
cannot be responsible for possible mistakes in this manual, nor for the consequences.

Hi-Spec Xcel 1250 Operators Manual
Hi-Spec Engineering reserves the right to make changes or improvements at any time without incurring any obligation to
make such changes on products sold previously.
3
Contents
Page
Symbols 4
Designated use of machine 4
Introduction 5
Technical specifications & dimensions 6
Safety decals 7
General safety 8
Safety checklist 8
PTO shaft safety 10
Getting started – Tractor requirements 11
Machine overview 11
Attaching to a tractor 12
Fitting PTO shaft 13
Road transportation 13
Working with the machine 14
Loading the spreader 14
Spreading controls 14
Spreading solid material 15
Spreading flow-able material (slurries, sewage pellets etc.) 15
Maintenance 16
Correct maintenance and inspection procedures 16
Recommended maintenance 17
Bolt tightening torques 17
Tyre Details 17
Greasing and maintenance points 18
Sales and service 20
Warranty Terms 21
Conditions of Sale 22
Registration forms 24
EC Machinery Directive 26

Hi-Spec Xcel 1250 Operators Manual
Hi-Spec Engineering reserves the right to make changes or improvements at any time without incurring any obligation to
make such changes on products sold previously.
4
Symbols
To focus attention on certain subjects or actions the following symbols are used.
WARNING / DANGER OF LIFE
Danger of injury or death.
CAREFUL
Danger of machine damage.
ATTENTION
Additional information of possible problems
TIP
Suggestions and advise
Designated Use of Machine
The Hi-Spec Xcel 1250 Muckspreader is exclusively designed for use of
transporting and spreading agricultural manure.
Hi-Spec Engineering will not be held responsible for any loss or damage
resulting from machine applications other than those specified above. Any other use
of the machine may be put to is entirely at the owners/operators risk. The
Designated use of a Xcel 1250 includes that the operating, maintenance and repair
instructions given by the manufacturer will be strictly fulfilled. Designated use means
operating the Xcel1250 is exclusively for persons familiar with the machine and fully
aware of the associated risks involved in operating it.
By any alteration of safety equipment, the Declaration of Conformity, as well
as the CE sign on machine loses it validity

Hi-Spec Xcel 1250 Operators Manual
Hi-Spec Engineering reserves the right to make changes or improvements at any time without incurring any obligation to
make such changes on products sold previously.
5
Introduction
Congratulations on Purchasing a Hi-Spec Xcel 1250.
You must read the following manual before using machine
The way you care for and maintain this machine will decide its future
performance. This manual has been carefully written to help you maintain the
condition of your machine. Read this manual carefully to learn how to operate and
service your machine correctly. Failure to do so could result in personal injury or
machine damage.
The Hi-Spec Xcel 1250 has been designed and manufactured in compliance
with the following directives and standards. Machinery Directive 98/37/EEC.
Harmonised standards EN 292 pt 1:1991, EN 292 pt 2:1991, EN 60204-1:1993, EN
1553:2000, EN 1050:1996.
This manual should be kept within the vicinity of the machine at all times and
should be considered a permanent part of your machine. It should remain with the
machine should you decide to sell it.
Warranty is provided as a part of Hi-Spec Engineering’s support program for
customers who operate and maintain this machine and equipment as described in
this manual. This warranty provides you the assurance that Hi-Spec Engineering will
back its machines should defects appear within the warranty period. If the machine is
abused, or modified to change its performance beyond the original factory
specifications, the warranty will become void and improvements may be denied.
All information, illustrations and specifications in this manual are based on the
latest product information available at the time of publication.
It is the policy of Hi-Spec Engineering to improve its products and designs
whenever it is practical and possible to do so. We reserve the right to make changes
or improvements at any time without incurring any obligation to make such changes
on products sold previously
Thank You For Choosing Hi-Spec Engineering

Hi-Spec Xcel 1250 Operators Manual
Hi-Spec Engineering reserves the right to make changes or improvements at any time without incurring any obligation to
make such changes on products sold previously.
6
Technical Specifications and Dimensions
Standard Xcel 1250 Specification
Painted red chassis and body, fixed front towing eye, stand fitted on drawbar, braked
axle, 200 h.p. rated gearbox, 580/70 R38 radial tyres, automatic chain tensioners,
slurry door, flow control floor chain speed adjustment, over run clutch and shear bolt
protection on main drive system, wide angle PTO shaft, hydraulic brakes, protective
cover on lights.

Hi-Spec Xcel 1250 Operators Manual
Hi-Spec Engineering reserves the right to make changes or improvements at any time without incurring any obligation to
make such changes on products sold previously.
7
Safety Decals
The decals consist of a picture representing the danger and a picture to show
how to avoid it.
You will find these signs located near specific hazards on your machinery.
Please pay attention to these signs for your own safety.
Safety signs should be maintained and replaced when necessary. They must
be kept clean and clearly legible.
If you need a replacement sign or have lost your user manual you must not
operate the machine. Please contact your Hi-Spec authorised dealer or Hi-
Spec Engineering directly and we will issue you a replacement.
Warning
Always read the operating manual and safety instructions
before use.
Warning
When the machine is operating stones or other objects can
cause injures. Always keep a safe distance.
Warning
After the first operating hour and then every 25 operating
hours, check tyre pressure and tighten wheel nuts.
Warning
PTO shafts can cause serious injury or death. Stay out of
range of shaft and wear close fitting clothing.
Warning
When the machine is moving never stand between the
tractor and the manure spreader.
Warning
Touching any rotating parts can cause serious injuries.
Always keep a safe distance when machine is operating.
Warning
Fingers can be cut off between belts/chains and gearwheels.
Always ensure safety guards are in place.
Warning
Gearwheels and rotating parts can cause serious injuries.
Never touch rotating parts when the machine is operating.
Warning
Maximum PTO speed for this machine is 1000 rpm.

Hi-Spec Xcel 1250 Operators Manual
Hi-Spec Engineering reserves the right to make changes or improvements at any time without incurring any obligation to
make such changes on products sold previously.
8
General Safety
Keep a first-aid kit and a fire extinguisher close by at all times, if possible, on your
tractor with this operator instruction manual.
Have an emergency plan.
Keep all emergency numbers close by; write them into your manual.
Inspect your machine carefully each time before use; this will only take a minute.
Always climb the ladder and check inside the machine before starting or filling it,
to make certain it is empty.
Stop machine when leaving unattended.
Children should never be in the area when your Xcel 1250 is in operation.
Using an Xcel 1250 is a one-man operation therefore there should be no other
person(s) in the vicinity of the machine while in use.
Remember that the first step to avoiding danger is to recognise the hazards.
Safety Checklist
Always disconnect all power sources before carrying out any adjustment or
maintenance.
Always check inside the machine to make sure it is empty.
Always check around the machine making sure everything is in order; this will
only take a minute.
Study this manual. Provide training to new users. Like all farm machinery, any
machine is potentially dangerous when under the control of untrained personnel.
Exercise extreme care when loading manure into the machine.
Always ensure guards and other safety devices are kept in good working order.
Replace if necessary.
Keep clear of all moving parts.
Always use shear bolts recommended to you by Hi-Spec Engineering.
Always keep all hydraulic hoses and electric cables clear from PTO shaft.
Always apply the handbrake before unhitching and park the machine in a level
area.

Hi-Spec Xcel 1250 Operators Manual
Hi-Spec Engineering reserves the right to make changes or improvements at any time without incurring any obligation to
make such changes on products sold previously.
9
Always use the ladder for inspecting inside the machine. Do not climb up the side
of the machine.
Always take extra precautions when using the machine on hilly or sloping ground.
Never permit young persons or spectators to operate PTO driven equipment or
stand anywhere close by when the machine is in operation.
Never permit untrained personnel to operate the machine without reading this
manual and or receiving training.
Never operate the machine without having all guards in place; they are there for
your safety and protection against serious injury and death.
Never remove guards while there is still power going into the machine, all power
must be off!
Never enter the machine while in operation.
Never wear loose clothes when operating machinery, if standing too close, your
clothing can pull you into the machine.
Never operate the machine if you think there could be large stones or foreign
objects inside, they could cause serious damage to your machine.
Never leave the machine running when unattended.
If the machine should become blocked with a stone or foreign object. Do not
attempt to free the object while the tractor is running.

Hi-Spec Xcel 1250 Operators Manual
Hi-Spec Engineering reserves the right to make changes or improvements at any time without incurring any obligation to
make such changes on products sold previously.
10
PTO Shaft Safety
The PTO shaft is a vital link in driving the machine. It is also a very dangerous
piece of equipment, therefore it is important to follow the manufacturer’s guidelines
on maintenance and repair. These guidelines are fixed to the PTO when new. They
should be removed, read carefully and then stored with this instruction manual for
future reference. If the guidelines are missing from the PTO Shaft please contact
your Hi-Spec dealer for another copy.
The irregular shape and connection joints of a turning shaft can cause serious
injury. The rotational force of the shaft is the main hazard.
Do not wear loose fitting clothing or articles such as jewellery that might get
caught in a turning PTO. The rotation of the PTO is 1000rpm when spreading.
Accidents can happen very fast therefore keep a safe distance from the shaft when it
is in use.
PTO Shafts account for most of tractor related
fatalities.
Make sure the shaft is guarded.
Replace the guards when they are
Damaged or missing.
Never use the machine with
Damaged or missing guards
In an emergency situation, take the PTO
Out of gear, stop the engine and set the brake.
Andere Handbücher für Xcel 1250
1
Inhaltsverzeichnis
Andere Hi-Spec Streuer Handbücher
Beliebte Streuer Handbücher anderer Marken

Fisher
Fisher POLY-CASTER 78601 Bedienungsanleitung

TurfEx
TurfEx RS7200 Betriebsanleitung

Ferris
Ferris Pathfinder Series Bedienungsanleitung

Fayat Group
Fayat Group DYNAPAC S100 Fehlerbehebungshandbuch

Art's-Way Manufacturing
Art's-Way Manufacturing X700 Installations- und Betriebshandbuch

EASTMAN
EASTMAN CR 500 Bedienungsanleitung












