HID Mercury MR62e Bedienungsanleitung
HID®Mercury™ MR62e OSDP Reader Interface Installation and Specifications
HID®Mercury™ MR62e OSDP Reader
Interface
Installation and Specifications
PLT-05249, A.1
August 2022
Copyright
© 2020 - 2022 HID Global Corporation/ASSA ABLOY AB. All rights reserved.
This document may not be reproduced, disseminated or republished in any form without the prior written permission of
HID Global Corporation.
Trademarks
HID GLOBAL, HID, the HID Brick logo, and HID Mercury are trademarks or registered trademarks of HID Global, ASSA
ABLOY AB, or its affiliate(s) in the US and other countries and may not be used without permission. All other trademarks,
service marks, and product or service names are trademarks or registered trademarks of their respective owners.
Contacts
For technical support, please visit: https://support.hidglobal.com.
What's new
Date Description Revision
August 2022 New branding. A.1
A complete list of revisions is available in Revision history.
PLT-05249, A.1 2 August 2022
Powering
Trusted Identities
HID®Mercury™ MR62e OSDP Reader Interface
Installation and Specifications
Section 01
Overview
1.1 MR62e reader interface
The MR62e OSDP reader interface provides a network connected interface to control two physical barriers using OSDP
readers and provides a solution for the OEM integrator for interfacing to OSDP readers and door hardware. The on-board
Ethernet with PoE/PoE+ support enables easy installation. The MR61e supports up to four OSDP readers configured as
paired or alternate readers.
Caution: For UL, the Power Sourcing Equipment (PSE) such as a PoE/PoE+ enabled network switch
and/or PoE/PoE+ power injectors must be UL Listed under UL294B.
One serial 2-wire RS-485 communication port is available that can accommodate up to four OSDP readers.
Four Form-C relay outputs can be used for door strike control or alarm signaling. The relay contacts are rated at 2 A @ 30
V DC, resistive and are in a dry contact configuration.
Six inputs are provided that can be used for monitoring the door contacts, exit push buttons, and alarm contacts. Input
circuits can be configured as unsupervised or supervised.
The MR62e requires PoE, PoE+ or local 12 V DC for power.
The MR62e may be mounted in a 3-gang switch box; a mounting plate is supplied with the unit or be mounted in an
enclosure; the supplied mounting plate has mounting holes that match the MR50 mounting footprint.
PLT-05249, A.1 4 August 2022
Powering
Trusted Identities
HID®Mercury™ MR62e OSDP Reader Interface
Installation and Specifications
1.2 MR62e hardware
PLT-05249, A.1 5 August 2022
Powering
Trusted Identities
HID®Mercury™ MR62e OSDP Reader Interface
Installation and Specifications
Section 02
MR62e wiring and setup
2.1 MR-51E connections
TB1-1 IN1 Input 1
TB1-2 IN1
TB1-3 IN2 Input 2
TB1-4 IN2
TB2-1 IN3 Input 3
TB2-2 IN3
TB2-3 IN4 Input 4
TB2-4 IN4
TB3-1 IN5 Input 5
TB3-2 IN5
TB3-3 IN6 Input 6
TB3-4 IN6
TB4-1 VO Auxiliary power output – 12 V DC
TB4-2 GND Auxiliary power output ground
TB4-3 VIN Input power – 12 V DC (from local power supply)
TB4-4 GND Input power ground
TB5-1 NO Relay K1 – Normally open contact
TB5-2 1-C Relay K1 – Common contact
TB5-3 NC Relay K1 – Normally closed contact
TB5-4 NO Relay K2 – Normally open contact
TB5-5 2-C Relay K2 – Common contact
TB5-6 NC Relay K2 – Normally closed contact
TB6-1 NO Relay K3 – Normally open contact
TB6-2 3-C Relay K3 – Common contact
TB6-3 NC Relay K3 – Normally closed contact
TB6-4 NO Relay K4 – Normally open contact
TB6-5 4-C Relay K4 – Common contact
TB6-6 NC Relay K4 – Normally closed contact
TB7-1 GND Reader power ground
TB7-2 TR- 2-Wire RS-485 TR- (B)1
TB7-3 TR+ 2-Wire RS-485 TR+ (A)1
TB7-4 RVO 12 V DC Reader power output
PLT-05249, A.1 7 August 2022
Powering
Trusted Identities
HID®Mercury™ MR62e OSDP Reader Interface
Installation and Specifications
1. Terms A & B are from the RS-485 standard.
2.2 Jumpers
Jumper Set at Description
J1 N/A Ethernet connection with PoE/POE+ support.
J2 N/A Factory use only.
J3 N/A Tamper switch (normally open contact). See 4.1 Additional mounting information
J4 N/A RS-485 Termination, install only if the MR62e is at the end of the communication bus.
J5 PoE MR62e powered from the Ethernet connection.
VIN MR62e powered from an external 12 V DC power source
connected to TB4-3 (VIN), TB4-4 (GND).
J6 – J13 N/A Factory use only.
2.3 DIP switches
The four switches on S1 DIP switch are used to configure the operating mode of the MR62e. DIP switches are read on
power-up except where noted.
1 2 3 4 Definitions
OFF OFF OFF OFF Normal operating mode.
ON X OFF OFF After initialization, enable default User Name (admin) and Password (password). The switch is
read on the fly, no need to reboot. See 2.12 IT security for additional information.
OFF ON OFF OFF Use factory default communication parameters.
ON ON OFF OFF Use OEM default communication parameters. Contact system manufacture for details. See 2.5
Bulk erase.
ON ON OFF OFF Bulk Erase prompt mode at power up. See 2.5 Bulk erase.
All other switch settings are unassigned and reserved for future use. X = don’t care.
2.4 Factory default communication parameters
Network: static IP address 192.168.0.251
Subnet mask 255.255.0.0
Default gateway 192.168.0.1
PLT-05249, A.1 8 August 2022
Powering
Trusted Identities
HID®Mercury™ MR62e OSDP Reader Interface
Installation and Specifications
2.5 Bulk erase
The bulk erase function can be used for the following:
lErase all configuration, sets MR62e to OEM setting (sanitize board).
lRestore to OEM default parameters.
2.5.1 Bulk erase steps
1. Set S1 DIP switches 1 and 2 to ON, and 3 and 4 to OFF.
2. Apply power to the MR62e.
3. Change DIP switches 1 or 2 to OFF within 10 seconds after LEDs 1 and 2, and LEDs 3 and 4 start flashing
alternately at a rate of 0.5 seconds. If these switches are not changed, the MR62e will power up using the OEM
default communication parameters.
4. LEDs 1 and 2 alternately flash at a 0.5 second rate while the memory is being erased.
5. Once the memory is eased, LED 1 will be on for about 3 seconds, then the MR62e will reboot.
Caution: Do not remove power during steps 3-5.
2.6 Input power
The MR62e is powered by one of two ways (jumper selected, J5):
lPower is supplied via the Ethernet connection using PoE or PoE+.
lLocal 12 V DC power supply, TB4-3 (VIN), TB4-4 (GND).
2.7 Communication wiring
Communication between the controller and the MR62e is Ethernet (10Base T/100Base-TX). It is not recommended to
connect the MR62e to a public intranet.
2.8 OSDP reader wiring
TB7 has connections for the 2-wire RS-485 OSDP communication bus and 12 V DC to power the OSDP readers. Up to
four OSDP readers are supported on the MR62e. This 12 V DC output is limited to .5 A. maximum. The OSDP reader
wiring diagram below shows the use of a 2-pair cable for data and power. If this cable cannot support the voltage/current
requirements, a 1-pair cable of sufficient gauge must be used for power. See Specifications.
The RS-485 termination jumper, J4, is only installed if the MR62e is at one end of the communication bus. Only devices at
each end of the communication bus are terminated, never install termination to more than two devices on the
communication bus.
Caution: When powering any remote device(s) by the MR62e, care must be taken not to exceed the
maximum current available. Cable gauge must also be evaluated. See Specifications for
details.
Note: For OSDP cable lengths greater than 200 ft (61 m) or EMF interference, install 120Ω +/- 2Ω resistor across
RS-485 termination ends. Data 0 and Data 1 wires for Wiegand may be reused for OSDP. However, standard
Wiegand cable may not meet RS-485 twisted pair recommendations. The reuse of cable works best on
shorter cable lengths at lower data rates.
PLT-05249, A.1 9 August 2022
Powering
Trusted Identities
HID®Mercury™ MR62e OSDP Reader Interface
Installation and Specifications
Typical OSDP reader wiring
2.9 Input circuit wiring
Typically, these inputs are used to monitor door position, request to exit, or alarm contacts. Input circuits can be
configured as unsupervised or supervised. When unsupervised, reporting consists of only the open or closed states.
When configured as supervised, the input circuit will report not only open and closed, but also open circuit, shorted,
grounded*, and foreign voltage*.
A supervised input circuit requires two resistors are added to the circuit to facilitate proper reporting. The standard
supervised circuit requires 1KΩ, 1% resistors and should be located as close to the sensor as possible. Custom end of
line (EOL) resistances may be configured via the host software.
*Grounded and foreign voltage states are not a requirement of UL 294 and therefore not verified by UL.
The input circuit wiring configurations shown are supported but may not be typical:
PLT-05249, A.1 10 August 2022
Powering
Trusted Identities
HID®Mercury™ MR62e OSDP Reader Interface
Installation and Specifications
Inhaltsverzeichnis
Andere HID Kartenleser Handbücher
HID
HID iCLASS SE R10F Bedienungsanleitung
HID
HID Technology Solutions 1139 Bedienungsanleitung
HID
HID Technology Solutions 1060 Bedienungsanleitung
HID
HID iCLASS RK40 Bedienungsanleitung
HID
HID iCLASS SE Biometric Reader Bedienungsanleitung
HID
HID iCLASS RK40 Bedienungsanleitung
HID
HID EdgeReader Bedienungsanleitung
HID
HID ProxPro II 5455 Bedienungsanleitung
HID
HID OMNIKEY eBase 1021 Bedienungsanleitung
HID
HID iCLASS SE Bedienungsanleitung
HID
HID Signo 20 Bedienungsanleitung
HID
HID iCLASS R10 Bedienungsanleitung
HID
HID iCLASS RK40 Bedienungsanleitung
HID
HID MaxiProx DFM Reader - 5375 Bedienungsanleitung
HID
HID iCLASS R10 Bedienungsanleitung
HID
HID iCLASS SE Bedienungsanleitung
HID
HID MaxiProx 5375A Bedienungs- und Wartungsanleitung
HID
HID MiniProx 5365 Bedienungsanleitung
HID
HID OMNIKEY 5121 Bedienungsanleitung
HID
HID iCLASS R90 Handbuch
Beliebte Kartenleser Handbücher anderer Marken
Rosslare
Rosslare DR-6255 Bedienungsanleitung
Lindy
Lindy 51541 Bedienungsanleitung
Diapro T?bbi Ürünler
Diapro T?bbi Ürünler Across System Bedienungsanleitung
Johnson Controls
Johnson Controls Kantech tyco ioSmart Bedienungsanleitung
ACS
ACS ACR122L Bedienungsanleitung
Secukey
Secukey S2-MF Bedienungsanleitung
