Hides DC-105 Bedienungsanleitung
Easy HD Expressway!
WWW.HIDES.COM.TW 1
DC-105
Quick Installation Guide
PACKAGE CONTENTS 2
POWER ON 2
CONNECT TO A DVB-T RECEIVER 3
ADJUST THE FOCUS OF THE LENS 3
CONNECT TO A CVBS MONITOR 4
MIC-IN 4
USB UART DONGLE 5
MONITOR BOOT MESSAGES 7
CUSTOM CONFIGURATION 9
MODULATION SETTING DESCRIPTION 11
VIDEO AND OTHER SETTING DESCRIPTION 14
UPDATE FIRMWARE 16
Easy HD Expressway!
WWW.HIDES.COM.TW 2
Package Contents
DC-105 Camera
USB UART dongle for configuration
A special USB cable for firmware update
Special USB cable for firmware update,
Power on
Apply 12V DC to DC-105. A red power LED will be on when power applied.
CVBS Video
Output
12 V DC-in
USB UART dongle
DVB-T RF Video
output
Reserved
DC-in header
Reserved UART2
Pin headers
Mic-in
Easy HD Expressway!
WWW.HIDES.COM.TW 3
It will take about 20~30 seconds for DC-105 to boot.
When the boot process is completed, it begins to transmit the camera video from the yellow BNC
connector in DVB-T, and the CVBS output (thru the black BNC) is also present.
A yellow LED will be on when transmitter is on.
Note:
1. Default RF channel is CH21, Frequency: 474MHz, BW:8 MHz, unless specified.
2. When initialization done, “###Camera Boot Finished###”message will be shown in the UART
debug port output; refer to more details below.
Connect to a DVB-T receiver
1. Connect the video RF output to a coaxial cable (or an antenna). A DVB-T receiver can be
either DVB-T TV, DVB-T STB or DVB-T USB receiver dongle.
2. The video output is full HD 1920x1080x30P H.264 format. Please make sure your receiver is
capable of HD decoding. (Many old DVB-T STB’s or TV’s can only decode 720x576 SD).
3. Default RF channel is CH21, Frequency:474MHz, BW:8 MHz, unless specified.
Adjust the Focus of the Lens
By default the focus of the lens may not be correct. Please turn the lens clockwise or
DVB-T
RF output
(Connected to
receiver)
Transmitter
LED (yellow)
Power LED
(red)
Easy HD Expressway!
WWW.HIDES.COM.TW 4
anti-clockwise to get the best focus.
Connect to a CVBS monitor
A CVBS video output is optional.
If it’s enabled, when the system boot is completed, there is a standard CVBS video output (default
PAL).
Mic-in
If it’s bare bone DC-105, a condenser microphone is included.
Easy HD Expressway!
WWW.HIDES.COM.TW 5
If DC-105 with housing, a 3 .5mm Phone Jack is provided.
Note: By default MIC-in feature is disabled.
When you want to enable MIC-in feature, it’s recommended to disable CVBS output with the
configuration kit for better audio quality.
USB UART Dongle
The USB UART dongle can be used to configure DC-105 or monitor the system boot status.
Easy HD Expressway!
WWW.HIDES.COM.TW 6
You may connect the UAB UART to a Laptop PC.
On most Windows platforms, the driver will be installed with in-box driver automatically.
However, if Windows prompts to install driver for the new device, please run
“PL2303_Prolific_DriverInstaller_v1.7.0.exe”, which can be found in the folder
“\PL2303_Prolific_DriverInstaller_v1.7.0”
If the device driver is installed well, there will be a new Com Port device, shown in Windows Device
Manager.
The com port assignment may vary depending on the PC configurations. In the following example, COM5 is
assigned.
The following picture show how the USB UART dongle is connected to DC-105.
Easy HD Expressway!
WWW.HIDES.COM.TW 7
Green wire: RXD
White wire: TXD
Black wire: GND
Monitor Boot Messages
When you connect the USB UART dongle to a Laptop PC, and driver is well installed, you may use
any UART terminal application (for example, Tera Term) or the DC-105 configuration tool
iTE_SerialTool.exe (described below) to monitor debug message.
The default communication parameters are 115200,n,8,1.
Easy HD Expressway!
WWW.HIDES.COM.TW 8
Tera Term.
iTE_SerialTool.exe:
Easy HD Expressway!
WWW.HIDES.COM.TW 9
Custom Configuration
Users may customize the configurations with a PC tool thru the USB UART dongle.
Connect the USB UART dongle to a Laptop PC, and make sure driver is well installed as described
in previous paragraph.
Easy HD Expressway!
WWW.HIDES.COM.TW 10
Launch “iTE_SerialTool.exe “.
Specify the correct COM port which corresponds to the USB UART dongle, then click on “Open”button.
Note: The com port’s friendly name is “Prolific USB-to-Serial Comm Port (COMxx)”.
The following shows the USB UART dongle is open successfully.
Click on “Get”button to retrieve current configurations.
Inhaltsverzeichnis
Andere Hides Sicherheitskamera Handbücher
