High Sec Labs SC21H-M Bedienungsanleitung
SECURE 2PORT KVM COMBINER | USER MANUAL
Models:
SC21H-M – Secure 2-Port HDMI Video KVM Combiner, M-Line HLT31947 Rev. 1.0
1
HSL Secure 2-Port KVM Combiner User Manual
TABLE OF CONTENTS
SECTIONS
Table of Contents 123
Introduction .......................................................... 2
HSL Secure 2-Port KVM Combiner Switch .....................................2
Installation............................................................ 3
Installing the Combiner.......................................................3
Operation............................................................. 5
Operation Modes Overview ..................................................5
Operating in User Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Selecting Display Layouts...................................................6
Full-Screen Mode...........................................................6
Side-By-Side Mode .........................................................7
Picture-In-Picture Mode ....................................................7
Custom Mode ..............................................................8
Switching Channel Control .................................................9
Configuring the Settings - in Admin Mode ..................................10
On-Screen Display Modes .................................................11
Channel Menu Options ....................................................12
Main Menu Options .......................................................13
Additional Settings ........................................................14
2
HSL Secure 2-Port KVM Combiner User Manual
INTRODUCTION
SECTIONS
Table of Contents 2 31
HSL Secure 2-Port KVM Combiner Switch
HSL’s Secure 2-Port KVM Combiner enables viewing and controlling
two computers:
•On the same display
•Using a single set of keyboard, mouse, USB, and audio peripherals
HSL’s KVM Combiner is the only product that combines a scaler, multi-
viewer, KVM switch, and video-wall controller - built into one.
The KVM Combiner was built according to multiple international-
security standards. These assure total isolation. So, no data leaks
between the two connected computers, via the switch or the
connected peripherals.
This guide tells you how to install, operate, and configure an HSL Secure
2-Port KVM Combiner.
3
HSL Secure 2-Port KVM Combiner User Manual
INSTALLATION
SECTIONS
Table of Contents 1 32
Installing the Combiner
Step 1 – Combiner Installation
1. Verify that all peripherals and computers are turned OFF before
connecting them to the Combiner.
2. To the Combiner’s Console ports, connect the keyboard, display,
mouse, and audio peripherals.
3. To the Combiner’s computer ports - for each of the two computers
- connect the keyboard, display, mouse, and audio cables. Make sure
that each computer cable is connected to the same computer-port
group.
Note: The two computers are represented by push buttons on the
product’s front panel. Once the Combiner is powered ON, you can
switch peripherals between the computers, by pressing either button.
Audio Cable
Mouse Cable
Display Cable
Keyboard Cable
Computers
CONSOLE PORTS COMPUTER PORTS
Audio Keyboard Mouse
Display
4
HSL Secure 2-Port KVM Combiner User Manual
INSTALLATION
SECTIONS
Table of Contents 1 32
Step 2 – Power ON the Combiner
1. Turn ON both PCs.
2. Connect the power supply and power ON the Combiner.
The Combiner boots up, as follows:
•If you are using the Combiner for the first
time, the default display mode is picture-
in-picture (PiP).
•Otherwise, the Combiner boots into the
display mode used during the previous
power on, including either:
–Full-screen - either channel #1 only or
channel #2 only
–Picture-in-picture (PiP)
–Side-by-side
–Custom mode
Note: In case no picture is presented after powering on the Combiner,
connect an alternate display to the combiner’s display console port, or
perform a reset to factory default.
Multiple Sources
Speakers
Single
Keyboard & Mouse
SECURE
KVM COMBINER
SECURE
KVM COMBINER
PC #1
PC #2
Move mouse
to switch PCs
5
HSL Secure 2-Port KVM Combiner User Manual
OPERATION
SECTIONS
Table of Contents 1 2 3
Operation Modes Overview
The Combiner operates in two modes:
•User mode (default) - User mode is the KVM Combiner’s normal
use mode. User mode lets you:
•Change between a wide variety of display layouts
•Switch mouse-and-keyboard control between the two computers
•Admin mode - Admin mode is the KVM Combiner’s configuration
mode. Admin mode lets you set, for example, the:
•Combiner resolution
•Custom channel window size and layout
•Channel frame and title display
•Channel aspect ratio
Operating in User Mode
The User mode (default) is the KVM Combiner’s normal use mode.
To enter User mode, press: Left Ctrl | Left Ctrl | u
Note: To clear all settings and restore the device to its original
configuration, press: Left Ctrl | Left Ctrl | F11 | r
This section shows you how to:
•Change between a wide variety of display layouts
•Switch mouse-and-keyboard control between the two computers
6
HSL Secure 2-Port KVM Combiner User Manual
OPERATION
SECTIONS
Table of Contents 1 2 3
Selecting Display Layouts
There are four display modes available in User mode:
•Full-screen
•Side-by-side
•Picture-in-picture (PiP)
•Custom
Full-Screen Mode
In full-screen mode, only one of the two computers is displayed (in full-
screen).
To display in full-screen mode:
•Press: Left Ctrl | Left Ctrl | z
This displays Channel #1 in full-screen mode.
Channel #1
•Then, to swap Channel #2 into full-screen mode,
press: Left Ctrl | Left Ctrl | w
Channel #2
7
HSL Secure 2-Port KVM Combiner User Manual
OPERATION
SECTIONS
Table of Contents 1 2 3
Side-By-Side Mode
In side-by-side mode, one computer is displayed on the LEFT, and the
other, on the RIGHT.
To display in side-by-side mode:
1. Press: Left Ctrl | Left Ctrl | s
This displays Channel #1 ,on the LEFT and Channel #2, on the RIGHT.
Channel
#1
Channel
#2
2. Then, to swap positions, press: Left Ctrl | Left Ctrl | w
Channel
#2
Channel
#1
Picture-In-Picture Mode
In picture-in-picture (PiP) mode, one computer is displayed full-screen,
while the other is displayed as a floating small-sized window, in the
lower right-hand corner.
To display in picture-in-picture mode:
1. Press: Left Ctrl | Left Ctrl | p
This displays Channel #1, in full-screen and Channel #2, as a small
window.
Channel #1
Channel
#2
2. Then, to swap positions, press: Left Ctrl | Left Ctrl | w
Channel #2
Channel
#1
8
HSL Secure 2-Port KVM Combiner User Manual
OPERATION
SECTIONS
Table of Contents 1 2 3
Custom Mode
Custom mode lets you display a pre-configured custom-designed
layout.
Note: To learn how to configure a custom-designed layout and save
it as a preset for future use, see the Main Menu Options section.
To display the Custom-mode display preset:
1. Press: Left Ctrl | Left Ctrl | c
Here is an example of a possible Custom-mode-display preset:
Channel
#2
Channel
#1
2. Then, to swap positions, press: Left Ctrl | Left Ctrl | w
For the example above, Channels #1 and #2 swap places.
Channel
#1
Channel
#2
9
HSL Secure 2-Port KVM Combiner User Manual
OPERATION
SECTIONS
Table of Contents 1 2 3
Switching Channel Control
To eliminate the need to press the Combiner’s front-panel buttons, you
can switch between channels, using:
•Mouse movement
•Keyboard shortcuts
Switching Channel Control - Using a Mouse
In User mode, you can switch keyboard-and-mouse control - from one
computer to the other – by simply dragging the mouse cursor over the
computer’s channel window border.
For example:
1. Display channels in side-by-side mode, by pressing:
Left Ctrl | Left Ctrl | s
2. Now, move the mouse cursor between Channels #1 and #2, to freely
switch keyboard-and-mouse control.
Note: This works in all other display modes.
Channel
#1
Channel
#2
Switching Channel Control - Using Keyboard Shortcuts
In User mode, you can switch keyboard-and-mouse control -from one
computer to the other - by using the following keyboard shortcuts:
•To switch control to Channel #1, press:
Left Ctrl | Left Ctrl | 1
•To switch control to Channel #2, press:
Left Ctrl | Left Ctrl | 2, OR –
•To swap between channels, press:
Left Ctrl | Left Ctrl | w
Note: This works in all display modes.
Andere Handbücher für SC21H-M
1
Inhaltsverzeichnis
Andere High Sec Labs Netzwerk-Hardware Handbücher
Beliebte Netzwerk-Hardware Handbücher anderer Marken
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung
Yudor
Yudor YDS-16 Bedienungsanleitung
D-Link
D-Link ShareCenter DNS-320L Bedienungsanleitung
Samsung
Samsung ES1642dc Gebrauchsanweisung
Honeywell Home
Honeywell Home LTEM-PV Montageanleitung
