HIGHLEAD GC24818-1D Bedienungsanleitung

Parts Catalog

SHANGHAI HUIGONG NO.3 SEWING MACHINE FACTORY

GC24818-1D

Post Bed Basting Machine with auto trimmer

Instruction Manual

--- CONTENTS ---

Instruction Manual

CAUTIONS ON USE .......................................................... 1

1. Cautions on operation.................................................................... 1

2. Precautions before starting operation ....................................................... 1

3. Precautions for operating conditions ....................................................... 1

4. Connection of control box ............................................................... 1

5. Adjustment of needle bar stop position ..................................................... 1

CAUTIONS ON USE ......................................................... 2

1. Lubrication (1) ....................................................................... 2

2. Lubrication (2) ...................................................................... 2

OPERATION .................................................................. 3

1. Attaching the needle ................................................................... 3

2. Winding the bobbin thread ............................................................. 3

3. Threading the machine ................................................................. 3

4. Setting of bobbin ..................................................................... 3

5. Leading out the bobbin thread ............................................................ 3

6. Thread tension......................................................................... 3

7. Bobbin thread tension adjustment ......................................................... 4

8. Needle thread tension adjustment ......................................................... 4

9. Adjustment of thread tension regulator ..................................................... 5

10. Presser foot pressure adjustment ......................................................... 5

11. Adjustment of presser foot height ........................................................ 5

12. Timing of hook and needle ............................................................. 5

13. Timing between hook motion and take-up lever motion ....................................... 6

14. Timing between hook motion and opener motion............................................. 7

ADJUSTMENT OF THREAD TRIMMER ................................. 7

1. Driving knife adjustment ............................................................... 7

2. Adjusting the fixed knife position and bobbin thread clamping. ................................. 7

3. Adjustment of trimmer cam ............................................................. 8

Parts Catalog

A.ARM BED MECHANISM .............................................................. 9

B.THREAD TENSION REGULATOR MECHANISM ......................................... 11

C. NEEDLE BAR AND THREAD TAKE-UP MECHANISM .................................... 13

D. NEEDLE BAR & PRESSER FOOT MECHANISM .......................................... 15

E. HOOK SADDLE MECHANISM ........................................................ 17

F. KNIFE MECHANISM ................................................................ 20

G. LOWER SHAFT & OIL LUBRICATION MECHANISM ..................................... 22

H. ACCESSORIES ...................................................................... 24

CAUTIONS ON USE

1.Cautions on operation

1）When the power is turned on and off, keep your foot away from the pedal. Note that the needle goes up

to the UP position when the power switch is turned on.

2）Note that braking does not work if the power is turned off, or power failure takes place, during machine

operation.

3）Since dust or other foreign matter entering into the control box may cause malfunction or trouble, be

sure to keep control box cover closed during operation.

4）Do not use a multimeter to check the control circuit. Otherwise, semiconductors in the control circuit

might be damaged by voltage from the multimeter.

2. Precautions before starting operation：

1）Never operate the machine before filling the machine’s oil pan.

2）When a new sewing machine is first turned on, verify the rotational direction of the pulley with the

power on.

3）Verify the voltage and phase (single or three) with those given on the machine nameplate.

3. Precautions for operating conditions：

1）Avoid using the machine at abnormally high temperatures（35℃or higher）or low temperatures（5℃

or lower）.

2）Avoid using the machine in dusty conditions.

4. Connection of control box

The control box should be connected as shown to the right.

Note: (1) Be sure to turn the power switch off for safety before connecting or disconnecting the connectors.

(2) The combination of the machine heads with the motor control panels are specified below. Use special

care for the correct combination when replacing the machine head or motor control panel.

5. Adjustment of needle bar stop position

1）Adjust of “UP” position: When the pedal is kicked down by heel, the machine stops at “UP” position.

—1 —

If the marks deviate larger than 3 mm, adjust as follows.

（1） Disconnect the plug (12 pins) of cable from the

machine head.

（2） Run the machine and stop at “UP” position.

（3） While holding the pulley, insert the “adjusting

tool” in the hole “A”, then remove the tool.

2）Adjust of “Down” position: When the pedal is

“Neutral” the machine stops at “Down” position. If the marks

deviate large than 5 mm, adjust as follows.

（1） Disconnect the plug (12 pins) of cable from the machine head.

（2） Run the machine and stop at “Down” position.

（3） While holding the pulley, insert the “adjusting tool” in the hole “B”, then remove the tool.

3）Confirm the stop operation, then set the plug (12 pings) coming from the machine head into the

receptacle.

CAUTIONS ON USE：

1. Lubrication(1)(Fig.4)

Pour oil up to position “H” of the oil tank.

During operation, check the oil level periodically, and in

cases where the oil level is below position “L”, replenish the

oil supply up to position “H”.

Use white spindle oil.

2.Lubrication (2)(Fig.5)

When a new sewing machine is used for the first time, or

sewing machine left out of use for a long time is used again,

replenish a suitable amount of oil to the portions indicated by

arrow in the fig.

Note: Lubricate the Hook Base everyday.

○ 1-2 drops

● 3-4 drops

—2 —

OPERATION

1.Attaching the needle(Fig.7)

１）For needle, use “Mt×190”

２）Determine the needle gauge for thickness lf thread used.

３）Loosen the needle clamp screw.

４）Hold the needle with the prime groove turned to the front and

put it into the needle socket until it stops.

５）Tighten the needle clamp screw.

2.Winding the bobbin thread(Fig.8)

3.Threading the machine(Fig.9)

The needle should be threaded in the order numbered in the

right figure.

4.Setting of bobbin (Fig.10)

１）Raise flap 1 and remove the empty bobbin.

２）Insert bobbin 2 in such a way that when the thread is

unwound from it moves in the opposite direction to the

gripper.

３）Pass the thread through slit 5 and below spring 6, pass

the thread through slit 3 and pull about 3 cm through.

４）Close flap 1 and pass the thread through the flap’s guide 4.

5.Leading out the bobbin thread(Fig. 11)

Pick up the end of needle thread by left hand and lightly press down the pedal by toe to run the machine one

turn. When the needle thread is pulled up, the bobbin thread will be drawn out as shown in the right figure.

6.Thread tension (Fig.12)

—3 —

7.Bobbin thread tension adjustment( Fig.13)

The lower-thread tension should be set in accordance with the type of seam required. Adjust the tension

with screw 1. (Fig.13)

8.Needle thread tension adjustment

The needle thread tension can be adjusted by changing pressure of the tension disk, and force and stroke of

the thread take-up spring.

1）Tension disk pressure adjustment (Fig.14)

(1) In most cases, thread tension can by properly adjusted only by changing tightness of the tension

regulator thumb nut.

(2) To increase pressure, turn the nut clockwise.

(3) To decrease pressure, turn the nut counter-clockwise.

2）Thread take-up spring force/stroke adjustment（Fig.15）

Apply a screwdriver to the thread take-up spring stud and turn the stud. Spring force increases when the

screwdriver is turned counter-clockwise, and decreases when turned clockwise. If the stud is tight, remove the

face plate and loosen the screw of tension regulator slightly.

3）Thread take-up spring force/stroke adjustment（Fig.15）

—4 —

Loosen the stop screw, adjusting the stopper block, After the adjustment, be sure to tighten the set screw.

The standard stroke of thread take-up spring is from 6mm to 8mm.

9.Adjustment of thread tension regulator（Fig. 16）

—5 —

1）Adjustment of thread tension

regulator setting position. The

standard gap is about 0.5mm when

the tension release cam salience is in

contact with the tension release pin.

To adjust, loosen screw A and change

position of the thread tension

regulator properly.

２）Tension release timing adjustment. The tension release cam should

be set so that the tension release disks come to close at the time the needle

plunges into the throat plate.

10.Presser foot pressure adjustment（picture 17）

Loosen the pressure adjusting screw lock nut and turn the pressure

adjusting screw ③. Turn the screw clockwise to increase the pressure. Turn

the screw counter-clockwise to decrease the pressure.

Note: Do not change setting of screw ④. If the screw is too tight,

clapping noise may occur during operation.

11.Adjustment of presser foot height（picture 17）

１）Height of presser foot

The standard height of the presser foot at its lowest position is 1.0 mm

measured between the presser foot bottom surface and the throat plate top surface (see the detail of part ”A”).

To adjust the height of the presser foot, loosen the set screw ②used to secure the presser bar guide

bracket and vertically move the presser bar.

２）Stroke of presser foot

loosen screw ①and adjust position of presser bar lifting bracket so

that the presser foot starts going up when the needle point reaches

0.5mm-1.0mmabove the presser foot bottom surface.(When this adjustment

is made, the height of the presser foot at stop of the machine is about

26.5mm over the throat plate.)

12.Timing of hook and needle(Fig.18)

１）When the needle is at 2.2mm above its lowest position, the hook

and the needle should be located as described below.

The upper edge of needle eye is 1.3mm below the hook tip.

The clearance between the hook tip and the needle side surface is 0.05mm.

2）The relative positions of the hook and the needle can be adjusted as described below.

*The adjustment is easier when the presser foot and the throat plate are previously removed.

Adjustment of hook tip position (Fig.19.Fig.20.Fig.21)

a.Lean outward the machine head. Loosen three hook shaft gear screws.

b.Rotate the balance wheel by hand to position the needle to 2.2mm

above the needle DOWN position.

c.Rotate the hook by hand to align the hook tip with the center of the

needle.

d.Adjust the lateral position of the hook saddle so that the clearance between the hook tip and the needle

side surface is 0.05mm. To adjust, loosen screws ①, ②and ③.

Note: Use care not to loosen set screw ③excessively, and not to disengage the hook shaft gear (small)

from the gear (large).

e.Tighten the loosened screws in the

following order:

3) Lightly press the gear (large)

against the side wall of hook saddle and

tighten set screw ③first.

4) Check the clearance between

the needle and the hook and then tighten

screw ①.

5) Finally tighten screw ②.

13.Timing between hook motion and take-up lever motion(Fig.22)

When the toothed belt is removed for replacement, the timing between the hook motion and the take-up

lever motion should be adjusted as follow：

１）Turn the balance wheel by land to locate the take-up lever to

its highest position.

２）Lean outward the machine head to make sure the arrow mark

(timing mark) on the toothed belt pulley meets the black line put on

the bearing bracket.

３）If the arrow mark is not in line with the black line, remove

the toothed belt and install again so that the two marks are in line, as

shown in the right figure.

—6 —

14.Timing between hook motion and opener motion(Fig.21)

１）Rotate the balance wheel by hand to locate the opener holder to the farthest position away from the

throat plate.

２）Make sure the clearance between the portion ①of bobbin case and the opener is about 0.2mm as

shown in the right figure.

３）If the clearance is too large or small, loosen opener screw ②and adjust position of the opener.

ADJUSTMENT OF THREAD TRIMMER

1.Driving knife adjustment

In resting position the rear edge of the driving knife should be flush with the front edge of the counter-knife.

The fixed knife should abut on the thread pulling knife along its total width.

The pivoting driving knife should abut on the fixed knife after approx.1/3 of its width.

The driving knife must not collide with the bobbin case.

The clearance between the lower blade edge of the driving knife a and the lower surface of the inner rotary

hook b should be 0.3-0.4mm.

Checking: Loosen two screws 1 for adjusting the resting position of the driving knife and adjust the

knife according to the standard, then tighten screws 1.

tightening the screws 1. The driving knife must be easily

2. Adjusting the fixed knife position and bobbin thread clamping.

g 5 has the function to hold the cut bobbin thread in order to avoid skipped stitches at the

seam beginning.

Attention:

Check the axial clearance of the knife shaft when

movable and the axial clearance as low as possible.

Checking:

The clamping sprin

—7 —

Inhaltsverzeichnis

Andere HIGHLEAD Nähmaschine Handbücher

HIGHLEAD

HIGHLEAD GG0028-1 Bedienungsanleitung

HIGHLEAD

HIGHLEAD GC188-MC Bedienungsanleitung

HIGHLEAD

HIGHLEAD GC1870-M Bedienungsanleitung

HIGHLEAD

HIGHLEAD DY-850 Bedienungsanleitung

HIGHLEAD

HIGHLEAD GC188-M-D Bedienungsanleitung

HIGHLEAD

HIGHLEAD GC2698-1 Bedienungsanleitung

HIGHLEAD

HIGHLEAD GK31058 SERIES Bedienungsanleitung

HIGHLEAD

HIGHLEAD HLK-1510 Bedienungsanleitung

HIGHLEAD

HIGHLEAD GC20618 Series Bedienungsanleitung

HIGHLEAD

HIGHLEAD GK600 SERIES Bedienungsanleitung

HIGHLEAD

HIGHLEAD GA0688-1 Stücklistenhandbuch

HIGHLEAD

HIGHLEAD GC24608-2 Bedienungsanleitung

HIGHLEAD

HIGHLEAD GC0318-2A Bedienungsanleitung

HIGHLEAD

HIGHLEAD GC0318-2A Bedienungsanleitung

HIGHLEAD

HIGHLEAD GC24698-2B Bedienungsanleitung

HIGHLEAD

HIGHLEAD GK0088 Bedienungsanleitung

HIGHLEAD

HIGHLEAD GA2688-1 Bedienungsanleitung

HIGHLEAD

HIGHLEAD GC1088 Series Bedienungsanleitung

HIGHLEAD

HIGHLEAD GC0618-1-SC Bedienungsanleitung

HIGHLEAD

HIGHLEAD GG80018 Bedienungsanleitung

HIGHLEAD

HIGHLEAD GM747-3 Bedienungsanleitung

HIGHLEAD

HIGHLEAD GC0618 I SC Bedienungsanleitung

HIGHLEAD

HIGHLEAD GC2008-M Bedienungsanleitung

HIGHLEAD

HIGHLEAD GC618-1 Bedienungsanleitung

Beliebte Nähmaschine Handbücher anderer Marken

Riccar

Riccar RL634DE Bedienungsanleitung

Pfaff

Pfaff 3307-1 SERIES Bedienungsanleitung

Siruba

Siruba C007JP Bedienungsanleitung

Husqvarna Viking

Husqvarna Viking Designer SE Bedienungsanleitung

Singer

Singer 148-5 Bedienungsanleitung

IKEA

IKEA SY Bedienungsanleitung

Pfaff

Pfaff 571 Bedienungsanleitung

Singer

Singer 15-91 Bedienungsanleitung

Brother

Brother BB370 Bedienungsanleitung

Pegasus

Pegasus WT100 Series Bedienungsanleitung

Reliable

Reliable 7100DB Bedienungsanleitung

Pfaff

Pfaff 937 Bedienungsanleitung

Singer

Singer 6038 Bedienungsanleitung

Singer

Singer 413K Bedienungsanleitung

Pfaff

Pfaff 1471 E1 Bedienungsanleitung

Kenmore

Kenmore 16677 - Serger Sewing Machine Bedienungsanleitung

Singer

Singer 400W4 Bedienungsanleitung

Singer

Singer Quantum XL-100 Bedienungsanleitung