HIK VISION DS-2CE71D8T-PIRL Bedienungsanleitung

TURBO HD

D8T PIR Series Turret

Camera

User Manual

Thank you for purchasing our product. If there are any

questions, or requests, do not hesitate to contact the

dealer.

This manual applies to the models below:

Model

DS-2CE71D8T-PIRL

This manual may contain technical incorrect places or

printing errors, and the content is subject to change

without notice. The updates will be added to the new

version of this manual. We will readily improve or

update the products or procedures described in the

manual.

0100001071019

Regulatory Information

FCC Information

Please take attention that changes or modification not

expressly approved by the party responsible for

compliance could void the user’s authority to operate

the equipment.

FCC compliance: This equipment has been tested and

found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection

against harmful interference when the equipment is

operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in

which case the user will be required to correct the

interference at his own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received,

including interference that may cause undesired

operation.

EU Conformity Statement

This product and - if applicable - the

supplied accessories too are marked with

"CE" and comply therefore with the

applicable harmonized European

standards listed under the Low Voltage Directive

2014/35/EU, the EMC Directive 2014/30/EU, the RoHS

Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products

marked with this symbol cannot be

disposed of as unsorted municipal waste in

the European Union. For proper recycling,

return this product to your local supplier

upon the purchase of equivalent new

equipment, or dispose of it at designated collection

points. For more information see: www.recyclethis.info.

2006/66/EC (battery directive): This product contains

a battery that cannot be disposed of as

unsorted municipal waste in the European

Union. See the product documentation for

specific battery information. The battery is

marked with this symbol, which may

include lettering to indicate cadmium (Cd), lead (Pb),

or mercury (Hg). For proper recycling, return the

battery to your supplier or to a designated collection

point. For more information see:

www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A)

standards requirements.

Warning

This is a class A product. In a domestic environment this

product may cause radio interference in which case the

user may be required to take adequate measures.

Safety Instruction

These instructions are intended to ensure that user can

use the product correctly to avoid danger or property

loss.

The precaution measure is divided into “Warnings” and

“Cautions”.

Warnings: Serious injury or death may occur if any of

the warnings are neglected.

Cautions: Injury or equipment damage may occur if any

of the cautions are neglected.

Warnings

In the use of the device, you must be in strict

compliance with the electrical safety regulations of

the nation and region.

Input voltage should meet both the SELV (Safety Extra

Low Voltage) and the Limited Power Source with 12

VDC according to the IEC60950-1 standard. Refer to

technical specifications for detailed information.

Do not connect multiple devices to one power

adapter to avoid over-heating or a fire hazard caused

by overload.

Make sure that the plug is firmly connected to the

power socket.

Make sure that the device is firmly fixed if wall

mounting or ceiling mounting is adopted.

If smoke, odor or noise rise from the device, turn off

the power at once and unplug the power cord, and

then contact the service center.

Never attempt to disassemble the camera by

unprofessional personal.

Cautions

Do not drop the camera or subject it to physical

shock.

Do not touch senor modules with fingers.

Do not place the camera in extremely hot, cold (the

operating temperature shall be -40°C to 60°C), dusty

or damp locations, and do not expose it to high

electromagnetic radiation.

If cleaning is necessary, use clean cloth with a bit of

ethanol and wipe it gently.

Do not aim the camera at the sun or extra bright

places.

The sensor may be burned out by a laser beam, so

when any laser equipment is in using, make sure that

the surface of sensor will not be exposed to the laser

beam.

Do not expose the device to high electromagnetic

radiation or extremely hot, cold, dusty or damp

environment.

To avoid heat accumulation, good ventilation is

required for the operating environment.

Warnings Follow

these safeguards to

prevent serious injury

or death.

Cautions Follow these

precautions to prevent

potential injury or

material damage.

Keep the camera away from liquid while in use for

non-water-proof device.

While in delivery, the camera shall be packed in its

original packing, or packing of the same texture.

Mark Description

Table 0-1 Mark Description

Mark

Description

DC Voltage

1Introduction

1.1 Product Features

The camera is applicable for both indoor and outdoor

conditions, and the application scenarios include road,

warehouse, underground parking lot, bar, etc..

The main features are as follows:

High performance CMOS sensor

Low illumination, 0.005 Lux @ (F2.0, AGC ON), 0 Lux

with IR

IR cut filter with auto switch

OSD menu with configurable parameters

Auto white balance

Internal synchronization

SMART IR mode

Visible alarm

PIR detection

3-axis adjustment

1.2 Overview

DC12VIN

Enclosure

Main Body

Mounting

Base

Power Cord

12 VDC

Video Cable (TVI)

White Light Source

PIR

Figure 1-1 Overview of Type I Camera

2Installation

Before you start:

Make sure that the device in the package is in good

condition and all the assembly parts are included.

Make sure that all the related equipment is power-off

during the installation.

Check the specification of the products for the

installation environment.

Check whether the power supply is matched with

your required output to avoid damage.

Make sure the wall is strong enough to withstand

three times the weight of the camera, and the

mount.

If the wall is cement, insert expansion screws before

installing the camera. If the wall is wooden, use

self-tapping screw to secure the camera.

If the product does not function properly, contact

your dealer or the nearest service center. Do NOT

disassemble the camera for repair or maintenance by

yourself.

2.1.1 Ceiling/Wall Mounting without Junction Box

Steps:

1. Disassemble the camera.

1). Rotate the camera to align the notch to one of the

marks.

2). Pry the mounting base to remove the mounting base

with the camera body with a flat object, e.g., a coin.

Notch

Mark Coin

2. Paste the drill template (supplied) to the place

where you want to install the camera.

3. Drill the screw holes, and the cable hole (optional)

in the ceiling/wall according to the drill template.

Ø 85 mm

Ø110 mm

73.6 mm

Ø 20 mm

Figure 2-1 Drill Template

Note:

Drill the cable hole, when adopting the ceiling outlet

to route the cable

4. Attach the mounting base to the ceiling/wall, and

secure them with supplied screws

Fixing Screw

Expansion Bolts

Figure 2-2 Attach the Mounting Base to the Ceiling

Note:

The supplied screw package contains self-tapping

screws, and expansion bolts.

For cement wall/ceiling, expansion bolts are

required to fix the camera. For wooden wall/ceiling,

self-tapping screws are required.

5. Route the cables through the cable hole, or the side

opening.

6. Align the camera with the mounting base, and

secure the camera on the mounting base.

Figure 2-3 Secure the Camera with Mounting Base

7. Connect the corresponding cables, such as power

cord, and video cable.

8. Power on the camera to check whether the image

on the monitor is gotten from the optimum angle. If

not, adjust the camera according to the figure below

to get an optimum angle.

Rotation Position

[0°to 360°]

Tilt Position

[0°to 75°]

Pan Position

[0°to 360°]

Figure 2-4 3-axis Adjustment

1). Hold the camera body and rotate the enclosure

to adjust the pan position [0°to 360°].

2). Move the camera body up and down to adjust

the tilt position [0°to 75°].

3). Rotate the camera body to adjust the rotation

position [0°to 360°].

2.1.2 Mounting with Inclined Ceiling Mount

Before you start:

You need to purchase an inclined ceiling mount

separately.

Steps:

1. Paste the drill template (supplied) to the place

where you want to install the camera.

2. Drill screw holes, and the cable hole on the

ceiling/wall according to the supplied drill template.

Screw Hole

Cable

Hole

Figure 2-5 The Drill Template

3. Disassemble the inclined ceiling mount by the screw

driver.

4. Install the turret camera’s mounting base on the

inclined ceiling mount’s cover with three PM4

screws.

Figure 2-6 Install Turret Camera’s Mounting Base

5. Install the inclined ceiling mount’s body on the

ceiling/wall with four PA4 ×25 screws, as shown in

Figure 2-8.

Figure 2-7 Fix the Inclined Ceiling Mount’s Body

6. Combine the inclined ceiling mount’s cover with its

body with supplied screws.

7. Repeat steps 5 to 8 of the 2.1.1 Ceiling/Wall

Mounting without Junction Box to complete the

installation.

Figure 2-8 Fix the Camera to the Inclined Ceiling Mount

2.1.3 Ceiling/Wall Mounting with Junction Box

Before you start:

You need to purchase a junction box separately.

Steps:

1. Paste the drill template on the ceiling/wall.

2. Drill screw holes and the cable hole (optional) in the

ceiling/wall according to the holes of the drill

template.

Figure 2-9 Drill Template of the Junction Box

Note:

Drill the cable hole, when adopting the ceiling outlet

to route the cable.

3. Take apart the junction box, and align the screw

holes of the turret camera’s mounting base with

those on junction box’s cover.

4. Fix the mounting base on junction box’s cover by

supplied screws.

Figure 2-10 Install Turret Camera’s Mounting Base

5. Secure the junction box’s body with supplied screws

on the ceiling/wall.

Figure 2-11 Install the Junction Box’ Camera Body on

Ceilling/Wall

6. Combine the junction box’s cover with the junction

box’s body.

7. Repeat steps 5 to 8 of 2.1.1 Ceiling/Wall Mounting

without Junction Box to install the camera to the

junction box.

Figure 2-12 Fix the Camera to the Junction Box

2.1.4 Wall Mounting

Before you start:

You need to purchase a wall mount separately.

Steps:

1. Drill four screw holes in the wall according to the

holes of the mount.

2. Install the mount to the wall by aligning the four

screw holes of the bracket with expansion screws on

the wall.

3. Secure the mount with four hex nuts and washers.

Wall Mount

Figure 2-13 Install the Bracket

4. Install the mounting base of the turret camera to

the wall mount, and secure them with supplied

screws.

Figure 2-14 Install the Mounting Base to the Bracket

5. Route the cables through the mount.

6. Repeat steps 6 to 8 of 2.1.1 Ceiling/Wall Mounting

without Junction Box to complete the installation.

3Menu Description

Purpose:

Call the menu by clicking button on the PTZ Control

interface, or call the preset No.95.

Steps:

1. Connect the camera with the TVI DVR, and the

monitor, shown as the figure 3-1.

Camera

TVI DVR

Monitor

Figure 3-1 Connection

2. Power on the analog camera, TVI DVR, and the

monitor to view the image on the monitor.

3. Click PTZ Control to enter the PTZ Control interface.

4. Call the camera menu by clicking button, or call

the preset No. 95.

AWB

BRIGHTNESS

MAIN MENU

FORMAT

DAY NIGHT

VIDEO

SETTING

FUNC

RESET

SAVE & EXIT

PRIVACY

EXPOSURE MODE

AGC

SENSE UP

MODE

RETURN

MODE

RETURN

CONTRAST

SHARPNESS

COLOR GAIN

3 DNR

MIRROR

RETURN

MOTION

CAM ID

RETURN

LANGUAGE

W-LIGHT

MODE

Figure 3-2 Main Menu Overview

5. Click the direction arrow to control the camera.

1). Click up/down direction button to select the

item.

2). Click Iris + to confirm the selection.

3). Click left/right direction button to adjust the

value of the selected item.

3.1 FORMAT

PAL (Phase Alternating Lines)

PAL is a color encoding system for analog television

used in broadcast television systems in most countries.

NTSC: (National Television System Committee)

NTSC is the analog television system that is used in

most of North America, parts of South America,

Myanmar, South Korea, etc.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HIK VISION IP-Kamera Handbücher

HIK VISION

HIK VISION DS-2CE56D1T-IRM Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD812P(N)-IR1(IR3) Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD2065FWD-I Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD752MF-E Series Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD732F-E Series Bedienungsanleitung

HIK VISION

HIK VISION DS-2CE72DFT-F Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD762MF-FBH Series Bedienungsanleitung

HIK VISION

HIK VISION ColorVu DS-2CD2 7G1-L Series Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD712P(N) Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD852MF-E Series Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD862MF-E Series Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD2942F Bedienungsanleitung

HIK VISION

HIK VISION DS-2DE7530IW-AE Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD752MF-FBH Series Bedienungsanleitung

HIK VISION

HIK VISION DS-2TD2636B-10/P Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD2023G0-I Bedienungsanleitung

HIK VISION

HIK VISION E-series Bedienungsanleitung

HIK VISION

HIK VISION UD21533B-A Bedienungsanleitung

HIK VISION

HIK VISION DS-2CC51D5S-AVPIR3 Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD2612F-I(S) Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD832F-E Series Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD726F-PT(W) Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD892P(N)-IR1(IR3) Bedienungsanleitung

HIK VISION

HIK VISION UD.6L0201D1633A01 Bedienungsanleitung

Beliebte IP-Kamera Handbücher anderer Marken

FLIR

FLIR Exx series Bedienungsanleitung

Avigilon

Avigilon H4A-BO1-IR Bedienungsanleitung

Digital Watchdog

Digital Watchdog DWCA-C128-64 Bedienungsanleitung

ShareTech

ShareTech AV1 Bedienungsanleitung

Ezviz

Ezviz C6C Bedienungsanleitung

Melchioni

Melchioni UCAM 2015 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/ESD-4630 Bedienungsanleitung

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Bedienungsanleitung

Mitel

Mitel 6800i Series Service-Handbuch

Vitek

Vitek VTC-IR403-212NP Bedienungsanleitung

THOMSON

THOMSON DSC - 323W Bedienungsanleitung

AVer

AVer FB2027 Bedienungsanleitung

ENFORCER

ENFORCER EV-T5105-N2SQ Bedienungsanleitung

Wansview

Wansview NC543 Bedienungsanleitung

Eneo

Eneo MCB-64A0003M0A Bedienungsanleitung

deView electronics

deView electronics CBDNI36F Bedienungsanleitung

Swann

Swann SwannEye Bedienungsanleitung

LevelOne

LevelOne IP CamSecure Bedienungsanleitung