HIK VISION DS-3WF Series Bedienungsanleitung

Wireless Bridge

Quick Start Guide

Legal Information

About this Manual

The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information

hereinafter are for description and explanation only. The information contained in the Manual is subject to change,

without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision

website (https://www.hikvision.com/).

Please use this Manual with the guidance and assistance of professionals trained in supporting the Product.

Trademarks

and other Hikvision’s trademarks and logos are the properties of Hikvision in various jurisdictions.

Other trademarks and logos mentioned are the properties of their respective owners.

Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITS

HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND “WITH ALL FAULTS AND ERRORS”. HIKVISION

MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY

QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO

EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,

INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA,

CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT

(INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT,

EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS.

YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION

SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES

RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER,

HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.

YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE

FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING

THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT

LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY

RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR

PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR

BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR

FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS.

Preface

Applicable Models

This manual is applicable to the DS-3WF Series wireless bridge.

Symbol Conventions

The symbols that may be found in this document are defined as follows.

Safety Instructions

This is a class A product and may cause radio interference in which case the user may be required

to take adequate measures.

No naked flame sources, such as lighted candles, should be placed on the device.

The serial port of the device is used for debugging only.

Keep vertical downward when moving or using the equipment.

Never place the device in an unstable location. The device may fall, causing serious personal

injury or death.

If the device is powered by terminals connected to the power cord, ensure correct voltage and

wiring of the terminals for connection to mains supply.

If the device installation is needed:

1. Install the device according to the instructions in Quick Start Guide.

2. To prevent injury, this device must be securely attached to the installation surface in

accordance with the installation instructions.

Symbol

Description

Provides additional information to emphasize or supplement

important points of the main text.

Indicates a potentially hazardous situation, which if not avoided,

could result in equipment damage, data loss, performance

degradation, or unexpected results.

Indicates a hazard with a high level of risk, which if not avoided, will

result in death or serious injury.

iii

In the use of the product, you must be in strict compliance with the electrical safety regulations

of the nation and region.

The socket-outlet shall be installed near the device and shall be easily accessible.

Do not connect several devices to one power adapter as adapter overload may cause

overheating or a fire hazard.

If a power adapter is provided in the device package, use the provided adapter only. If no power

adapter is provided, ensure the power adapter or other power supply complies with Limited

Power Source. Refer to the product label for the power supply output parameters.

Please make sure that the plug is firmly connected to the power socket.

Do not touch the bare components (such as the metal contacts of the inlets) and wait for at

least 5 minutes, since electricity may still exist after the device is powered off.

The interface varies with the models. Please refer to the product datasheet for details.

If the device needs to be wired by yourself, select the corresponding wire to supply power

according to the electric parameters labeled on the device. Strip off wire with a standard wire

stripper at corresponding position. To avoid serious consequences, the length of stripped wire

shall be appropriate, and conductors shall not be exposed.

Make sure that the power has been disconnected before you wire, install, or disassemble the

device.

If smoke, odor, or noise arises from the device, immediately turn off the power, unplug the

power cable, and contact the service center.

If the device supports wall mounting or ceiling mounting, the mounting surface shall be able to

withstand the additional force of three times the weight of the device but not less than 50 N.

The device and its associated mounting means shall remain secure during the installation. After

the installation, the device, including any associated mounting plate, shall not be damaged.

Refer to Datasheet for details.

Chapter 1 Introduction

The 5 GHz wireless bridge (hereinafter referred to as the device) is used for long-distance wireless

connection, which is suited for elevator wireless video transmission between sites in a LAN.

Interface/Button

The devices consist of the AP and CPE. The following introduces the interfaces/buttons of the AP

and CPE respectively.

AP Interface/Button

CPE Interface/Button

Device Interface/Button Description

No.

Interface/Button

Description

Reset

Long press for 4 seconds to restore to factory settings.

PoE/WAN

The 10/100 Mbps adaptive RJ45 port, also can be

used as a PoE port.

Indicator

Device Indicator

Device Indicator Description

PoE/LAN 1

The 10/100 Mbps adaptive RJ45 port, also can be

used as a PoE port.

4/5

LAN 2/LAN 3

The 10/100 Mbps adaptive RJ45 port.

No.

Indicator

Description

Signal Strength

Indicator

Solid on

The devices are matched.

Solid red, yellow, and green: The

wireless signal is strong.

Solid red and yellow, unlit green: The

wireless signal is normal.

Solid red, unlit yellow and green: The

wireless signal is weak. Please adjust

the position and direction of the

device.

Unlit

The devices are not matched.

Network Port

Indicator

Solid Green

The port is connected.

Flashing Green

The port is transmitting data. The faster

the indicator flashes, the greater the

transmission rate is.

Unlit

The port is disconnected or connection is

abnormal.

Packing List

Please check if there is any damage of the package first. According to the packing list, make sure

no item is lost. After checking all the items included, you can continue to install the device.

Packing List

Application Scene

The following application scenes are for your reference only. The actual scene prevails.

The device image used here is only for example purpose. The actual device may vary with models.

Power Indicator

Solid Green

The device is powered on normally.

Unlit

No power supply connected or power

supply is abnormal.

Item

Quantity

Item

Quantity

Item

Quantity

Wireless

Bridge

× 2

PoE Injector

×2

Power

Adapter

× 2

Cable Tie

× 4

Quick Start

Guide

× 1

Regulatory

Compliance

and Safety

Information

× 1

Application Scenes

Chapter 2 Installation & Connection

Preparation for Installation

To avoid device damage or personal injury caused by improper usage of the device, please follow

the preparations below.

Use the attached power adapter and PoE injector to power the device.

The distance between the AP and the CPE should be less than the suggested distance to secure

transmission rate.

At least 2 m distance should be kept between two adjacent devices.

Install the device in the place where the maintenance personnel can operate easily.

The devices should be installed face to face and the max. angle of deviation is 30°.

Disconnect the power supply when you have the device serviced.

The temperature of the cover area will be high when the device is working. In the circumstances,

only personnel with relevant professional knowledge, such as installation and maintenance

personnel, are allowed to operate the device.

AP Installation

The AP device can be magnetically mounted or mounted by using a wall mount bracket. It is

recommended to mount the device magnetically.

Attach the back magnet of the AP device to the steel surface of the machine room, to keep the

device installed horizontally. The following two diagrams are for your reference.

Magnetic Mounting Manner 1

Magnetic Mounting Manner 2

The bracket should be prepared by yourself.

Align screw holes of the wall mount bracket to those of the device back, and insert screws into

the aligned screw holes and tighten the screws to fasten the bracket and the AP device.

Fasten Bracket and AP Device

Align screw holes at the joint part of the bracket to those of the bracket arm, and insert the

matched screw into the aligned hole and tighten the screw to fasten the bracket and the

bracket arm.

Andere Handbücher für DS-3WF Series

Inhaltsverzeichnis

Andere HIK VISION Netzwerk-Hardware Handbücher

HIK VISION

HIK VISION DS-7608NI-I2/8P Bedienungsanleitung

HIK VISION

HIK VISION DS-7600NI-12 Series Bedienungsanleitung

HIK VISION

HIK VISION HiLook NVR 104MH-D/4P Bedienungsanleitung

HIK VISION

HIK VISION DS-9600NI-M8 Series Bedienungsanleitung

HIK VISION

HIK VISION DS-7732NI-I4/16P Bedienungsanleitung

HIK VISION

HIK VISION DS-7604NI-Q1 Bedienungsanleitung

HIK VISION

HIK VISION DS-9616NI-I8 Bedienungsanleitung

HIK VISION

HIK VISION DS-76xxNI-Ex/xP Bedienungsanleitung

HIK VISION

HIK VISION iDS-9632NXI-I8/16S Bedienungsanleitung

HIK VISION

HIK VISION DS-7600NI Series Bedienungsanleitung

HIK VISION

HIK VISION HWN-2100H Series Bedienungsanleitung

HIK VISION

HIK VISION DS-9600NI-SH Series Bedienungsanleitung

HIK VISION

HIK VISION iDS-96000NXI-I16B Series Bedienungsanleitung

HIK VISION

HIK VISION DS-7608NI-K2/8P/4G Bedienungsanleitung

HIK VISION

HIK VISION 7600NI-SE Series Bedienungsanleitung

HIK VISION

HIK VISION DS-7108NI-E1/V/W Bedienungsanleitung

HIK VISION

HIK VISION DS-7608NI-M2 Series Bedienungsanleitung

HIK VISION

HIK VISION DS-9608NI-ST Series Bedienungsanleitung

HIK VISION

HIK VISION DS-7600NI-E1/A Bedienungsanleitung

HIK VISION

HIK VISION HWN-2104H-4P Bedienungsanleitung

HIK VISION

HIK VISION DS-7100NI-SL series Bedienungsanleitung

HIK VISION

HIK VISION DS-7104NI-SL Bedienungsanleitung

HIK VISION

HIK VISION DS-9608NI-I8 Bedienungsanleitung

HIK VISION

HIK VISION DS-9632NI-I8 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung