HIK VISION DS-2CC52H1T-FITS Bedienungsanleitung
HD Fisheye Camera
User Manual
UD01467B
User Manual
Thank you for purchasing our product. If there are any questions,
or requests, please do not hesitate to contact the dealer.
This manual applies to the model DS-2CC52H1T-FITS.
This manual may contain several technical incorrect places or
printing errors, and the content is subject to change without
notice. The updates will be added to the new version of this
manual. We will readily improve or update the products or
procedures described in the manual.
Privacy Notice
Surveillance laws vary by jurisdiction. Check all relevant laws in
your jurisdiction before using all this product for surveillance
purpose to ensure that your use of this product conforms.
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to
comply with the limits for a digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to
correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized
European standards listed under the Low Voltage
Directive 2014/35/EU, the EMC Directive 2014/30/EU.
2002/96/EC (WEEE directive): Products marked
with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment,
or dispose of it at designated collection points. For more
information see: www.recyclethis.info.
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific battery
information. The battery is marked with this
symbol, which may include lettering to indicate
cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling,
return the battery to your supplier or to a designated collection
point. For more information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards
requirements.
1000001060520
1Introduction
1.1 Product Features
This series of camera adopts high performance sensor and
advanced circuit board design technology. It features high
resolution, low distortion, and low noise, etc. It is suitable for
surveillance system and image process system.
5 Megapixel high-performance CMOS
HD TVI output, up to 5Mega ` resolution
0.01Lux @ (F1.2,AGC ON), 0 Lux with IR
IR cut filter with auto switch
OSD menu
Built-in microphone, 1-ch audio output
1.2 Overview
Camera Body
Photoconductive
Resistance Microphone
Audio Cable (Red)
HD TVI Cable (Gray)
12V DC Power Cable
Lens
Base Plate
2Installation
Before you start:
Please make sure that the device in the package is in good
condition and all the assembly parts are included.
Make sure that all the related equipment is power-off during
the installation.
Check the specification of the products for the installation
environment.
Check whether the power supply is matched with your
required output to avoid damage.
Please make sure the wall is strong enough to withstand three
times the weight of the camera and the mounting.
If the wall is the cement wall, you need to insert expansion
screws before you install the camera. If the wall is the wooden
wall, you can use self-tapping screw to secure the camera.
If the product does not function properly, please contact your
dealer or the nearest service center. Do not disassemble the
camera for repair or maintenance by yourself.
2.1 Ceiling Mounting
Steps:
1. Drill two screw holes and the cable hole according to the
supplied drill template.
22
φ24
φ102
2-φ3.4
41.75
2. Align the screw holes and cable hole on the drill template and
the base plate, and then fix the base plate to the ceiling with
the two supplied screws.
Ceiling
Base Plate
Notes:
●For cement wall, you need to use the expansion screw to fix the
mount.
●For wooden wall, you can just use the self-tapping screw to fix the
mount.
3. Route the cables through the cable hole or the side opening
according to the actual needs, and connect the corresponding
cables including power cable, network cable, audio and alarm
cables, etc.
4. Align the triangle mark on the camera and base plate, and
then rotate the camera clockwise until it is locked up by the
three bayonet joints on the base plate.
5. To disassemble the camera: Press the Push button on the base
plate, rotate the camera anticlockwise, and then you can
remove the camera from the base plate.
PUSH
6. To adjust the view angle: Rotate the camera body clockwise or
anticlockwise with the base plate, and then you can adjust the
camera to the desired view angle.
15°15°
2.2 Wall Mounting with a Slant Mounting Base
Before you start:
You need to purchase a slant mounting base separately if this
mounting method is selected.
Steps:
1. Drill two screw holes and the cable hole according to the
supplied drill template.
2-26
φ24
φ102
2-φ3.4
41.75
83.5
2. Fix the slant mounting base to the wall with the screws.
Mounting Base
Wall
3. Align the screw holes on the slant mounting base and the base
plate, and then secure the base plate on the slant mounting
base with the two supplied screws.
4. Route the cables through the cable hole or the side opening
according to the actual needs, and connect the corresponding
cables including power cable, network cable, audio and alarm
cables, etc.
5. Align the triangle mark on the camera and mounting base, and
then rotate the camera clockwise until it is locked up.
6. The installation is complete.
7. To disassemble the camera: Press the Push button on the base
plate, rotate the camera anticlockwise, and then you can
remove the camera from the base plate.
PUSH
2.3 Wall Mounting with a Bracket
Before you start:
You need to purchase the bracket separately if this mounting
method is selected.
Steps:
1. Unfasten and remove the screw marked in the figure, and then
disassemble the bracket.
Inhaltsverzeichnis
Andere HIK VISION Sicherheitskamera Handbücher
HIK VISION
HIK VISION TURBO HD DS-T116 Bedienungsanleitung
HIK VISION
HIK VISION DS-2CE16C2T-IR Bedienungsanleitung
HIK VISION
HIK VISION DS-2TD2117-6/V1 Bedienungsanleitung
HIK VISION
HIK VISION iDS-TCR803-B Bedienungsanleitung
HIK VISION
HIK VISION DS-2CE71D0T-PIRL Bedienungsanleitung
HIK VISION
HIK VISION iVMS-4200 Bedienungsanleitung
HIK VISION
HIK VISION DS-2DT6223-AELY Bedienungsanleitung
HIK VISION
HIK VISION UD04315B Bedienungsanleitung
HIK VISION
HIK VISION DS-2DP0818Z-D Bedienungsanleitung
HIK VISION
HIK VISION DS-2CD2D21G0/M-D/NF Bedienungsanleitung
HIK VISION
HIK VISION Ezviz ez360 Series Bedienungsanleitung
HIK VISION
HIK VISION DS-2CD2646G2T-IZS Bedienungsanleitung
HIK VISION
HIK VISION IDS-2CD7046G0-AP Bedienungsanleitung
HIK VISION
HIK VISION DS-2TD2336-75 Bedienungsanleitung
HIK VISION
HIK VISION TurboHD DS-2CE56D7T-IT Z Series Bedienungsanleitung
HIK VISION
HIK VISION DS-2AE714 Bedienungsanleitung
HIK VISION
HIK VISION HiLook Series Bedienungsanleitung
HIK VISION
HIK VISION EPI-4215-DE3 Bedienungsanleitung
HIK VISION
HIK VISION DS-2DY7236IX-A Bedienungsanleitung
HIK VISION
HIK VISION DS-2CD3086G2-IS Bedienungsanleitung
