HIK VISION DS-2CE16D0T-WL3 Bedienungsanleitung

TURBO HD

TVI Bullet Camera

User Manual

UD04876B

User Manual

Thank you for purchasing our product. If there are any

questions, or requests, do not hesitate to contact the

dealer.

This manual applies to the model listed below.

Type

Model

Type I

DS-2CE16D0T-WL3

Type II

DS-2CE16D0T-WL5

This manual may contain several technically incorrect

places or printing errors, and the content is subject to

change without notice. The updates will be added to the

new version of this manual. We will readily improve or

update the products or procedures described in the

manual.

0100001070302

Regulatory Information

FCC Information

FCC compliance: This equipment has been tested and

found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against

harmful interference when the equipment is operated in

a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction

manual, may cause harmful interference to radio

communications. Operation of this equipment in a

residential area is likely to cause harmful interference in

which case the user will be required to correct the

interference at his own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received,

including interference that may cause undesired

operation

EU Conformity Statement

This product and - if applicable - the

supplied accessories too are marked with

"CE" and comply therefore with the

applicable harmonized European standards

listed under the EMC Directive 2014/30/EU, the RoHS

Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products

marked with this symbol cannot be

disposed of as unsorted municipal waste in

the European Union. For proper recycling,

return this product to your local supplier

upon the purchase of equivalent new

equipment, or dispose of it at designated collection

points. For more information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A)

standards requirements.

Safety Instruction

These instructions are intended to ensure that user can

use the product correctly to avoid danger or property

loss.

The precaution measure is divided into “Warnings” and

“Cautions”

Warnings: Serious injury or death may occur if any of the

warnings are neglected.

Cautions: Injury or equipment damage may occur if any

of the cautions are neglected.

Warnings

In the use of the device, you must be in strict

compliance with the electrical safety regulations of the

nation and region.

Input voltage should meet both the SELV (Safety Extra

Low Voltage) and the Limited Power Source with 12

VDC according to the IEC60950-1 standard. Refer to

technical specifications for detailed information.

Do not connect multiple devices to one power adapter

to avoid over-heating or a fire hazard caused by

overload.

Make sure that the plug is firmly connected to the

power socket.

Make sure that the device is firmly fixed if wall

mounting or ceiling mounting is adopted.

If smoke, odor or noise rise from the device, turn off

the power at once and unplug the power cord, and

then contact the service center.

Never attempt to disassemble the camera by

unprofessional personal.

Cautions

Do not drop the camera or subject it to physical shock.

Do not touch senor modules with fingers.

If cleaning is necessary, use clean cloth with a bit of

ethanol and wipe it gently.

Do not aim the camera at the sun or extra bright places.

The sensor may be burned out by a laser beam, so

when any laser equipment is in using, make sure that

the surface of sensor will not be exposed to the laser

beam.

Do not expose the device to high electromagnetic

radiation or extremely hot, cold, dusty or damp

environment.

To avoid heat accumulation, good ventilation is

required for the operating environment.

Keep the camera away from liquid while in use for non-

water-proof device.

Warnings Follow

these safeguards to

prevent serious injury

or death.

Cautions Follow these

precautions to prevent

potential injury or

material damage.

While in delivery, the camera shall be packed in its

original packing, or packing of the same texture.

Introduction

1.1 Product Features

The camera is applicable for outdoor conditions, and the

application scenarios include road, parking lot, campus,

etc..

The main features are as follows:

High performance CMOS sensor

1080p resolution

Auto white balance

Auto electronic shutter

Auto gain control (AGC)

White supplement light

Up the Coax (HIKVISION-C)

1.2 Overview

1.2.1 Type I Camera Overview

Switch Cable

TVI Video Cable

Power Cord

(12 VDC )

White

Supplement Light

Lens

Sun Shield

Figure 1. 1 Type I Camera Overview

1.2.2 Type II Camera Overview

TVI Video Cable

Power Cord

( 12 VDC)

White

Supplement Light

Sun Shield

White Supplement

Light

Lens

Switch Cable

Figure 1. 2 Type II Camera Overview

Installation

2.1 Installation Preparation

Before you start:

Make sure that the device in the package is in good

condition and all the assembly parts are included.

Make sure that all the related equipment is power-off

during the installation.

Check the specification of the products for the

installation environment.

Check whether the power supply is matched with your

power output to avoid damage.

Make sure the wall is strong enough to withstand three

times the weight of the camera and the bracket.

If the wall is cement, insert expansion bolts before you

install the camera. If the wall is wooden, use self-

tapping screws to secure the camera.

If the product does not function properly, contact your

dealer or the nearest service center. Do NOT

disassemble the camera for repair or maintenance by

yourself.

Note:

Since type I camera and type II camera share the same

installation method, we take type I camera as the

example to describe the installation.

2.2 Wall Mounting

Before you start:

The package contains the wall mounting bracket.

Steps:

1. Attach the bracket to the wall.

2. Mark the screw holes on the wall according to the

holes on the bracket.

3. Drill the screw holes.

4. Attach the bracket to the wall and secure the camera

with supplied screws.

Figure 2. 1 Secure the camera to the wall

Note:

In the supplied screw package, both self-tapping

screws and expansion bolts are contained.

If the wall is cement, expansion bolts are required to

fix the camera. If the wall is wooden, self-tapping

screws are required.

5. Align the camera to the pedestal, and secure the

camera on the pedestal with supplied screws.

Screw

Pedestal

Figure 2. 2 Secure the Camera on the Bracket

6. Route the cables and connect the corresponding

power cord and video cable.

7. Power on the camera to check whether the image on

the monitor is gotten from the optimum angle. If not,

adjust the camera according to the figure below to

get an optimum angle.

1). Loosen the horizontal adjusting screw to adjust

the pan position (0°to 360°).

2). Tighten the horizontal adjusting screw.

3). Loosen the vertical adjusting screw to adjust the

tilt position (0°to 90°)

4). Tighten the vertical adjusting screw.

Horizontal Adjusting

Screw

Pan Position:

0° to 360°

Vertical Adjusting Screw

Tilt Position:

0° to 90°

Figure 2. 3 Angle Adjustment

2.3 Pendant Mounting

Before you start:

You need to purchase a pendant bracket first.

Steps:

1. Attach the bracket to the ceiling.

2. Mark the screw holes on the ceiling according to the

holes on the bracket.

3. Drill the screw holes.

4. Attach the bracket to the ceiling and secure the

camera with supplied screws.

Figure 2. 4 Fix the Bracket on the Ceiling

Note:

In the supplied screw package, both self-tapping

screws and expansion bolts are contained.

If the wall is cement, expansion bolts are required to

fix the camera. If the wall is wooden, self-tapping

screws are required.

5. Remove the screw on the top of the camera to

expose the screw hole.

Screw

Figure 2. 5 Remove the Screw

6. Align the screw hole on the top of the camera with

the pendant mounting bracket and rotate the camera

to get it fixed.

Adjusting Knob

Figure 2. 6 Fix the Camera to the Bracket

7. Route the cables and connect the corresponding

power cord and video cable.

8. Power on the camera to check whether the image on

the monitor is gotten from the optimum angle. If not,

adjust the camera according to the figure below to

get an optimum angle.

1). Loosen the adjusting knob to adjust the pan

position (0°to 360°) and tilt position (0°to 90°)

2). Tighten the adjusting knob.

Adjusting Knob

Tilt Position:

0° to 90°

Pan Position:

0° to 360°

Figure 2. 7 Angle Adjustment

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HIK VISION Sicherheitskamera Handbücher

HIK VISION

HIK VISION TURBO HD DS-2CE57H0T-VPITE Bedienungsanleitung

HIK VISION

HIK VISION DS-2DF5220S Bedienungsanleitung

HIK VISION

HIK VISION TURBO HD DS-2CE5AD0T-VPIT3F Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD886BF-E Bedienungsanleitung

HIK VISION

HIK VISION DS-2CZ2182P-WD Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD2520F Bedienungsanleitung

HIK VISION

HIK VISION DS-2XM6756FWD-IS Bedienungsanleitung

HIK VISION

HIK VISION PanoVu 6A Series Bedienungsanleitung

HIK VISION

HIK VISION TURBO HD D0T PIR Series Bedienungsanleitung

HIK VISION

HIK VISION DS-2XC6685G0 Bedienungsanleitung

HIK VISION

HIK VISION DS-2CV2046G0-IDW Bedienungsanleitung

HIK VISION

HIK VISION D7T Series Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD2063G0-I Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD1621FWD-IZ Bedienungsanleitung

HIK VISION

HIK VISION DS-2CE56D0T-I2FB Bedienungsanleitung

HIK VISION

HIK VISION DS-2TD4166-50/V2 Bedienungsanleitung

HIK VISION

HIK VISION TURBO HD DS-2CE56D8T-IT3ZF Bedienungsanleitung

HIK VISION

HIK VISION Mini Dome Camera Series Bedienungsanleitung

HIK VISION

HIK VISION DS-2CE5582P(N)-VFIR3 Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD8253F-EI(S) Bedienungsanleitung

HIK VISION

HIK VISION HiWatch Series Bedienungsanleitung

HIK VISION

HIK VISION UD07275B Bedienungsanleitung

HIK VISION

HIK VISION DS-2DF8836IX-AEL Bedienungsanleitung

HIK VISION

HIK VISION I0D2400 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung