HIK VISION IPC-B220-IZ Bedienungsanleitung

Network Bullet Camera

Quick Start Guide

Network Bullet Camera·Quick Start Guide

Quick Start Guide

About this Manual

This Manual is applicable to IPC-B2XX-IZ Network Bullet Camera.

The Manual includes instructions for using and managing the

product. Pictures, charts, images and all other information

hereinafter are for description and explanation only. The

information contained in the Manual is subject to change, without

notice, due to firmware updates or other reasons. Please find the

latest version in the company website

Please use this user manual under the guidance of professionals.

Regulatory Information

FCC Information

Please take attention that changes or modification not expressly

approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

FCC compliance: This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is

Network Bullet Camera·Quick Start Guide

encouraged to try to correct the interference by one or more of the

following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied

accessories too are marked with "CE" and comply

therefore with the applicable harmonized European

standards listed under the EMC Directive 2014/30/EU, the RoHS

Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked

with this symbol cannot be disposed of as unsorted

municipal waste in the European Union. For proper

recycling, return this product to your local supplier

upon the purchase of equivalent new equipment, or dispose of it at

designated collection points. For more information see:

www.recyclethis.info

Network Bullet Camera·Quick Start Guide

2006/66/EC (battery directive): This product

contains a battery that cannot be disposed of as

unsorted municipal waste in the European Union.

See the product documentation for specific battery

information. The battery is marked with this symbol,

which may include lettering to indicate cadmium (Cd), lead (Pb), or

mercury (Hg). For proper recycling, return the battery to your

supplier or to a designated collection point. For more information

see: www.recyclethis.info

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (B)/NMB-3(B) standards

requirements.

Safety Instruction

These instructions are intended to ensure that user can use the

product correctly to avoid danger or property loss.

The precaution measure is divided into “Warnings” and “Cautions”

Warnings: Serious injury or death may occur if any of the warnings

are neglected.

Cautions: Injury or equipment damage may occur if any of the

cautions are neglected.

Warnings Follow these

safeguards to prevent

Cautions Follow these

precautions to prevent potential

Network Bullet Camera·Quick Start Guide

Warnings

●Proper configuration of all passwords and other security

settings is the responsibility of the installer and/or end-user.

●In the use of the product, you must be in strict compliance with

the electrical safety regulations of the nation and region. Please

refer to technical specifications for detailed information.

●Input voltage should meet both the SELV (Safety Extra Low

Voltage) and the Limited Power Source with 24 VAC or 12 VDC

according to the IEC60950-1 standard. Please refer to technical

specifications for detailed information.

●Do not connect several devices to one power adapter as

adapter overload may cause over-heating or a fire hazard.

●Please make sure that the plug is firmly connected to the power

socket. When the product is mounted on wall or ceiling, the

device shall be firmly fixed.

●If smoke, odor or noise rise from the device, turn off the power

at once and unplug the power cable, and then please contact

the service center.

Cautions

serious injury or death.

injury or material damage.

Network Bullet Camera·Quick Start Guide

●Make sure the power supply voltage is correct before using the

camera.

●Do not drop the camera or subject it to physical shock.

●Do not touch sensor modules with fingers. If cleaning is

necessary, use clean cloth with a bit of ethanol and wipe it

gently. If the camera will not be used for an extended period,

please replace the lens cap to protect the sensor from dirt.

●Do not aim the camera at the sun or extra bright places.

Blooming or smearing may occur otherwise (which is not a

malfunction), and affect the endurance of sensor at the same

time.

●The sensor may be burned out by a laser beam, so when any

laser equipment is in using, make sure that the surface of

sensor will not be exposed to the laser beam.

●Do not place the camera in extremely hot, cold (the operating

temperature shall be-30°C ~to 60°C , or -40°C ~ to 60°C if the

camera model has an “H” in its suffix), dusty or damp locations,

and do not expose it to high electromagnetic radiation.

●To avoid heat accumulation, good ventilation is required for

operating environment.

●Keep the camera away from liquid while in use.

●While in delivery, the camera shall be packed in its original

packing, or packing of the same texture.

●Regular part replacement: a few parts (e.g. electrolytic

capacitor) of the equipment shall be replaced regularly

according to their average enduring time. The average time

varies because of differences between operating environment

Network Bullet Camera·Quick Start Guide

and using history, so regular checking is recommended for all

the users. Please contact with your dealer for more details.

●Improper use or replacement of the battery may result in

hazard of explosion. Replace with the same or equivalent type

only. Dispose of used batteries according to the instructions

provided by the battery manufacturer.

●If the product does not work properly, please contact your

dealer or the nearest service center. Never attempt to

disassemble the camera yourself. (We shall not assume any

responsibility for problems caused by unauthorized repair or

maintenance.)

Network Bullet Camera·Quick Start Guide

Table of Contents

1 Appearance Description ................................................................. 8

2 Installation.................................................................................... 10

2.1 Memory Card Installation.............................................. 10

2.2 Camera Mounting ......................................................... 13

2.2.1 Direct Mounting ...................................................... 13

2.2.2 Mounting with a Junction Box ................................. 16

2.2.3 Mounting with a Gang Box ...................................... 17

2.3 Zoom and Focus Adjustment......................................... 18

2.4 Installation of Network Cable Water-proof Jacket

(Optional) ................................................................................. 19

3 Setting the Network Camera over the LAN .................................. 22

3.1 Wiring ........................................................................... 22

3.2 Activating the Camera................................................... 23

3.2.1 Activation via Web Browser..................................... 23

3.2.2 Activation via SADP Software................................... 24

3.3 Modifying the IP Address .............................................. 26

4 Accessing via Web Browser .......................................................... 30

5 Operating via CCTV Guard App..................................................... 32

5.1 Enable Guarding Vision Service on Camera................... 32

Enable Guarding Vision Service via SADP Software.. 325.1.1

Enable Guarding Vision Service via Web Browser .... 335.1.2

5.2 CCTV Guard Setup......................................................... 35

5.3 Adding Camera to CCTV Guard...................................... 35

5.4 Initializing the Memory Card......................................... 37

Network Bullet Camera·Quick Start Guide

1Appearance Description

The overview of camera is shown below.

789

Overview of CameraFigure 1-1

DescriptionTable 1-1

No.

Description

Sun Shield

Front Cover

IR LED

Lens

Memory Card Slot

Network Bullet Camera·Quick Start Guide

No.

Description

Reset Button

Camera Body

Bracket

Network Cable

Power Cord

Note:

Press RESET about 10s when the camera is powering on or rebooting

to restore the default settings, including the user name, password, IP

address, port No., etc.

Inhaltsverzeichnis

Andere HIK VISION Sicherheitskamera Handbücher

HIK VISION

HIK VISION DS-2CE16H0T-ITE Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD63C5G0-IS Bedienungsanleitung

HIK VISION

HIK VISION DS?2CD753F?E Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD6986F Bedienungsanleitung

HIK VISION

HIK VISION UD04310B Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD3786G2T-IZS Bedienungsanleitung

HIK VISION

HIK VISION DS-2XS6A25G0-I/CH20S40 Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD2443G0-IW Series Bedienungsanleitung

HIK VISION

HIK VISION DS-2DE2A204IW-DE3(C0)(S6) Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD2355FWD-I Bedienungsanleitung

HIK VISION

HIK VISION DS-2CE59U7T-VPIT3ZF Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD3356G2-IS Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD5A46GO-IZS Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD63C5G0-IVS Bedienungsanleitung

HIK VISION

HIK VISION TurboHD DS-2CE56D7T-IT Z Series Bedienungsanleitung

HIK VISION

HIK VISION 23 Series Bedienungsanleitung

HIK VISION

HIK VISION DS-2CE16D8T-AIT3ZE Bedienungsanleitung

HIK VISION

HIK VISION HiLook IPC-T250H Bedienungsanleitung

HIK VISION

HIK VISION DS-2DF5220S Bedienungsanleitung

HIK VISION

HIK VISION THC-B129-P Bedienungsanleitung

HIK VISION

HIK VISION P07Z35LW4T30 Bedienungsanleitung

HIK VISION

HIK VISION NETWORK CAMERA Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD8153F-EWI Bedienungsanleitung

HIK VISION

HIK VISION UD01570B Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung