HIK VISION THC-T129-P Bedienungsanleitung

HiLook Series

2 MP Turret Camera

User Manual

Thank you for purchasing our product. If there are any

questions, or requests, do not hesitate to contact the

dealer.

This manual applies to the models below:

Type

Model

Type I

THC-T129-P

Type II

THC-T129-M

Type III

THC-T229-M

This manual may contain several technical mistakes or

printing errors, and the content is subject to change

without notice. The updates will be added to the new

version of this manual. We will readily improve or

update the products or procedures described in the

manual.

0101002000102

Regulatory Information

FCC Information

Please take attention that changes or modification not

expressly approved by the party responsible for

compliance could void the user’s authority to operate

the equipment.

FCC compliance: This equipment has been tested and

found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection

against harmful interference when the equipment is

operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in

which case the user will be required to correct the

interference at his own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received,

including interference that may cause undesired

operation.

EU Conformity Statement

This product and - if applicable - the

supplied accessories too are marked with

"CE" and comply therefore with the

applicable harmonized European

standards listed under the Low Voltage Directive

2014/35/EU, the EMC Directive 2014/30/EU, the RoHS

Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products

marked with this symbol cannot be

disposed of as unsorted municipal waste in

the European Union. For proper recycling,

return this product to your local supplier

upon the purchase of equivalent new

equipment, or dispose of it at designated collection

points. For more information see: www.recyclethis.info.

2006/66/EC (battery directive): This product contains a

battery that cannot be disposed of as

unsorted municipal waste in the European

Union. See the product documentation for

specific battery information. The battery is

marked with this symbol, which may

include lettering to indicate cadmium (Cd), lead (Pb), or

mercury (Hg). For proper recycling, return the battery

to your supplier or to a designated collection point. For

more information, see: www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A)

standards requirements.

Warning

This is a class A product. In a domestic environment this

product may cause radio interference in which case the

user may be required to take adequate measures.

Safety Instruction

These instructions are intended to ensure that user can

use the product correctly to avoid danger or property

loss.

The precaution measure is divided into “Warnings” and

“Cautions”.

Warnings: Serious injury or death may occur if any of

the warnings are neglected.

Cautions: Injury or equipment damage may occur if any

of the cautions are neglected.

Warnings

In the use of the device, you must be in strict

compliance with the electrical safety regulations of

the nation and region.

Input voltage should meet both the SELV (Safety Extra

Low Voltage) and the Limited Power Source with 12

VDC according to the IEC60950-1 standard and

IEC62368-1 standard. Refer to technical specifications

for detailed information.

Do not connect multiple devices to one power

adapter to avoid over-heating or a fire hazard caused

by overload.

Make sure that the plug is firmly connected to the

power socket.

Make sure that the device is firmly fixed if wall

mounting or ceiling mounting is adopted.

If smoke, odor or noise rise from the device, turn off

the power at once and unplug the power cord, and

then contact the service center.

Never attempt to disassemble the camera by

unprofessional personal.

Cautions

Do not drop the camera or subject it to physical

shock.

Do not touch senor modules with fingers.

Do not place the camera in extremely hot, cold (the

operating temperature shall be -40°C to 60°C), dusty

or damp locations, and do not expose it to high

electromagnetic radiation.

If cleaning is necessary, use clean cloth with a bit of

ethanol and wipe it gently.

Do not aim the camera at the sun or extra bright

places.

The sensor may be burned out by a laser beam, so

when any laser equipment is in using, make sure that

the surface of sensor will not be exposed to the laser

beam.

Do not expose the device to high electromagnetic

radiation or extremely hot, cold, dusty or damp

environment.

Warnings Follow

these safeguards to

prevent serious injury

or death.

Cautions Follow these

precautions to prevent

potential injury or

material damage.

To avoid heat accumulation, good ventilation is

required for the operating environment.

Keep the camera away from liquid while in use for

non-water-proof device.

While in delivery, the camera shall be packed in its

original packing, or packing of the same texture.

Mark Description

Table 0-1 Mark Description

Mark

Description

DC Voltage

1Introduction

1.1 Product Features

The main features are as follows:

High performance CMOS sensor

Smart light

4 in 1 video output

1.2 Overview

1.2.1 Overview of Type I Camera

DC12VIN

Mounting Base

Switch Button

Video Cable

Power Cord

Main Body

Enclosure

Figure 1-1 Overview of Type I Camera

Note:

Press and hold the switch button for 5 seconds to

switch the video output. Four kinds of video outputs

are available: TVI, AHD, CVI, and CVBS.

1.2.2 Overview of Type II Camera

DC12VIN

Screw

Clip Plate

Mounting Base

Trim Ring

Enclosure Main Body

Switch Button

Power Cord

Video Cable

Figure 1-2 Overview of Type II Camera

Note:

Press and hold the switch button for 5 seconds to

switch the video output. Four kinds of video outputs

are available: TVI, AHD, CVI, and CVBS.

1.2.3 Overview of Type III Camera

DC12VIN

Trim Ring

Enclosure

Main Body

Mounting

Base

Switch Button

Power Cord

Video Cable

Figure 1-3 Overview of Type III Camera

Note:

Press and hold the switch button for 5 seconds to

switch the video output. Four kinds of video outputs

are available: TVI, AHD, CVI, and CVBS.

2Installation

Before you start

Make sure that the device in the package is in good

condition and all the assembly parts are included.

Make sure that all the related equipment is power-off

during the installation.

Check the specification of the products for the

installation environment.

Check whether the power supply is matched with

your power output to avoid damage.

Make sure the wall is strong enough to withstand

three times the weight of the camera and the mount.

If the product does not function properly, contact

your dealer or the nearest service center. Do NOT

disassemble the camera for repair or maintenance by

yourself.

2.1 Installation of Type I Camera

2.1.1 Ceiling Mounting Without Junction Box

Steps:

1. Rotate the camera to align one of the marks with

the notch, and dissemble the camera.

Mark

Notch

Figure 2-1 Align the Mark and the Notch

2. Pry the enclosure open with a flat object, for

example, a coin, to dissemble the camera.

Figure 2-2 Dissemble the Camera

3. Paste the drill template (supplied) to the place

where you want to install the camera.

4. (Optional) For cement ceiling, drill the screw holes

with a 5.5 mm drill and insert the supplied wall

plugs.

Figure 2-3 Drill Template

5. (Optional) Drill the cable hole, when the cables are

routed through the ceiling.

6. Use two PA4 screws (supplied) to secure the

mounting base to the ceiling.

Figure 2-4 Secure the Base to the Ceiling

7. Install the camera back to the mounting base and

secure it.

Figure 2-5 Install the Camera Back

8. Connect the power cord and video cable.

9. Power on the camera to check whether the image

on the monitor is gotten from the optimum angle. If

not, adjust the camera according to the figure

below.

Rotation Position

[0°to 360°]

Tilt Position

[0°to 75°]

Pan Position

[0°to 360°]

Figure 2-6 3-Axis Adjustment

1). Rotate the enclosure to adjust the pan position

[0° to 360°].

2). Move the main body up and down to adjust the

tilt position [0° to 75°].

3). Rotate the main body to adjust the rotation

position [0° to 360°].

2.1.2 Ceiling Mounting with Junction Box

Before you start:

You need to purchase a junction box in advance.

Steps:

1. Loosen screws to take apart the junction box.

2. Paste the drill template for junction box to the place

where you want to install the camera.

3. (Optional) For cement ceiling, drill the screw holes

with a 5.5 mm drill and insert the supplied wall

plugs.

Figure 2-7 Drill Template for Junction Box

4. (Optional) Drill the cable hole, when the cables are

routed through the ceiling.

5. Secure the junction box body on the ceiling with

three PA4 × 25 screws that come with the junction

box.

Figure 2-8 Secure the Junction Box Body

6. Fix the mounting base onto the junction box cover

with two M4 × 10 screws.

Figure 2-9 Fix the Mounting Base

7. Route the cables through the bottom cable hole or

the side cable hole of the junction box.

8. Combine the junction box cover with its body and

secure it with three M3 screws.

Figure 2-10 Combine the Junction Box Cover and Body

9. Connect the power cord and video cable and put

the cables back into the junction box.

10. Refer to step 9 of 2.1.1 Ceiling Mounting Without

Junction Box to adjust the angle and finish the

installation.

2.1.3 Wall Mounting

Before you start:

You need to purchase a wall mount in advance.

Steps:

1. Drill Φ 10 mm screw holes in the wall where you

want to install the wall mount.

2. Use four M6 expansion bolts to fix the wall mount

onto the wall.

Figure 2-11 Fix the Wall Mount

3. Refer to steps 1 and 2 of 2.1.1 Ceiling Mounting

Without Junction Box to dissemble the camera.

4. Use two M4 screws to fix the mounting base onto

the wall mount.

Figure 2-12 Fix the Mounting Base onto the Wall Mount

5. Refer to steps 7 to 9 of 2.1.1 Ceiling Mounting

Without Junction Box to finish the installation.

Figure 2-13 Finish the Installation

2.2 Installation of Type II Camera

2.2.1 Ceiling Mounting without Junction Box

Steps:

6. Paste the drill template (supplied) to the place

where you want to install the camera.

7. (Optional) For cement ceiling, drill the screw holes

with a 5.5 mm drill and insert the supplied wall

plugs.

Figure 2-14 Drill Template

8. Loosen the screw and pull out the clip plate to

dissemble the camera.

Figure 2-15 Dissemble the Camera

9. Secure the mounting base to the ceiling with three

PA4 × 25 screws.

Figure 2-16 Attach the Gang Box to the Ceiling

10. Pull out the clip plate and install the camera back to

the mounting base. Push the clip plate back in to

secure the camera.

Figure 2-17 Install the Camera

11. Connect the power cord and video cable.

12. Power on the camera to check whether the image

on the monitor is gotten from the optimum angle. If

not, adjust the camera according to the figure

below.

Rotation Position

[0°to 360°]

Tilt Position

[0°to 75°]

Pan Position

[0°to 360°]

Figure 2-18 3-Axis Adjustment

1). Rotate the enclosure to adjust the pan position

[0° to 360°].

2). Move the main body up and down to adjust the

tilt position [0° to 75°].

3). Rotate the main body to adjust the rotation

position [0° to 360°].

13. Tighten the screw to finish the installation.

2.2.2 Ceiling Mounting with Junction Box

Before you start:

You need to purchase a junction box in advance.

Steps:

1. Paste the drill template for junction box to the place

where you want to install the camera.

2. (Optional) For cement ceiling, drill the screw holes

with a 5.5 mm drill and insert the supplied wall

plugs.

Figure 2-19 Drill Template

3. (Optional) Drill the cable hole, when the cables are

routed through the ceiling.

4. Take apart the junction box.

5. Secure the junction box body on the ceiling with PA4

× 25 screws that come with the junction box.

Figure 2-20 Secure the Junction Box Body

6. Route the cables through the bottom cable hole or

the side cable hole of the junction box.

7. Combine the junction box cover with its body and

secure it with three PM3 screws.

Figure 2-21 Combine the Junction Box Cover and Body

8. Fix the mounting base onto the junction box with

three M4 × 10 screws.

9. Connect the power cord and video cable and put

the cables back into the junction box.

10. Refer to steps 5, 7, and 8 of 2.2.1 Ceiling Mounting

without Junction Box to finish the installation.

2.2.3 Wall Mounting

Before you start:

You need to purchase a wall mount in advance.

Steps:

1. Drill Φ 10 mm screw holes in the wall where you

want to install the wall mount.

2. Use four M6 expansion bolts to fix the wall mount

onto the wall.

Figure 2-22 Fix the Wall Mount

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HIK VISION Sicherheitskamera Handbücher

HIK VISION

HIK VISION DS-2CD2112 Benutzerhandbuch

HIK VISION

HIK VISION DS-2CD2086G2-IU Bedienungsanleitung

HIK VISION

HIK VISION I0M1000 Bedienungsanleitung

HIK VISION

HIK VISION DS-2TD6237-50H4L/W Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD886BF-E Bedienungsanleitung

HIK VISION

HIK VISION UD.6L0201B1295A01 Benutzerhandbuch

HIK VISION

HIK VISION TURBO HD TVI-AC334-FD4/FD4-2.8 Bedienungsanleitung

HIK VISION

HIK VISION DS-2CE59H8T-(A)VPIT3ZF Bedienungsanleitung

HIK VISION

HIK VISION iDS-TCV500-B(I)/IM Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD1021G0-I Bedienungsanleitung

HIK VISION

HIK VISION DS-2TD4238-7/S2 Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD2D21G0/M-D/NF Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD2955FWD-I Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD7026G0-EP-I-H Bedienungsanleitung

HIK VISION

HIK VISION HiWatch HWI-T240H Bedienungsanleitung

HIK VISION

HIK VISION Turbo HD D0T Series Bedienungsanleitung

HIK VISION

HIK VISION DS-2XC6646G0/P-IZHS Bedienungsanleitung

HIK VISION

HIK VISION DS-2XE6126FWD-HS Bedienungsanleitung

HIK VISION

HIK VISION D8T Series Bedienungsanleitung

HIK VISION

HIK VISION Network Speed Dome Camera Bedienungsanleitung

HIK VISION

HIK VISION ULT-P6CUBE Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD7126G0-IZS Bedienerhandbuch

HIK VISION

HIK VISION DS-2CD7253F-EIZ Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD852F Series Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung