HIK VISION U7T Series Bedienungsanleitung

TURBO HD

U7T Series

Bullet & Turret Camera

User Manual

Thank you for purchasing our product. If there are any

questions, or requests, do not hesitate to contact the

dealer.

This manual applies to the models below:

Type

Model

Type I Camera

DS-2CE19U7T-(A)IT3ZF

Type II Camera

DS-2CE79U7T-IT3ZF

This manual may contain technical incorrect places or

printing errors, and the content is subject to change

without notice. The updates will be added to the new

version of this manual. We will readily improve or update

the products or procedures described in the manual.

0100001080717

Regulatory Information

FCC Information

Please take attention that changes or modification not

expressly approved by the party responsible for

compliance could void the user’s authority to operate the

equipment.

FCC compliance: This equipment has been tested and

found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against

harmful interference when the equipment is operated in

a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction

manual, may cause harmful interference to radio

communications. Operation of this equipment in a

residential area is likely to cause harmful interference in

which case the user will be required to correct the

interference at his own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received,

including interference that may cause undesired

operation.

EU Conformity Statement

This product and - if applicable - the

supplied accessories too are marked with

"CE" and comply therefore with the

applicable harmonized European standards

listed under the Low Voltage Directive 2014/35/EU, the

EMC Directive 2014/30/EU.

2012/19/EU (WEEE directive): Products

marked with this symbol cannot be

disposed of as unsorted municipal waste in

the European Union. For proper recycling,

return this product to your local supplier

upon the purchase of equivalent new equipment, or

dispose of it at designated collection points. For more

information see: www.recyclethis.info.

2006/66/EC (battery directive): This product

contains a battery that cannot be disposed

of as unsorted municipal waste in the

European Union. See the product

documentation for specific battery

information. The battery is marked with this

symbol, which may include lettering to indicate cadmium

(Cd), lead (Pb), or mercury (Hg). For proper recycling,

return the battery to your supplier or to a designated

collection point. For more information, see:

www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A)

standards requirements.

Warning

This is a class A product. In a domestic environment this

product may cause radio interference in which case the

user may be required to take adequate measures.

Safety Instruction

These instructions are intended to ensure that user can

use the product correctly to avoid danger or property

loss.

The precaution measure is divided into “Warnings” and

“Cautions”.

Warnings: Serious injury or death may occur if any of the

warnings are neglected.

Cautions: Injury or equipment damage may occur if any

of the cautions are neglected.

Warnings

In the use of the device, you must be in strict

compliance with the electrical safety regulations of the

nation and region.

Input voltage should meet both the SELV (Safety Extra

Low Voltage) and the Limited Power Source with 12

VDC according to the IEC60950-1 standard. Refer to

technical specifications for detailed information.

The camera is powered by the external DC power

supply (12 VDC, 1 A) which is complied with the LPS,

and the output current of this external DC power

supply must be no more than 6 A.

Do not connect multiple devices to one power adapter

to avoid over-heating or a fire hazard caused by

overload.

Make sure that the plug is firmly connected to the

power socket.

Make sure that the device is firmly fixed if wall

mounting or ceiling mounting is adopted.

If smoke, odor or noise rise from the device, turn off

the power at once and unplug the power cord, and

then contact the service center.

Never attempt to disassemble the camera by

unprofessional personal.

Cautions

Do not drop the camera or subject it to physical shock.

Do not touch senor modules with fingers.

Do not place the camera in extremely hot, cold (the

operating temperature shall be -40°C to 60°C), dusty or

damp locations, and do not expose it to high

electromagnetic radiation.

If cleaning is necessary, use clean cloth with a bit of

ethanol and wipe it gently.

Do not aim the camera at the sun or extra bright places.

The sensor may be burned out by a laser beam, so

when any laser equipment is in using, make sure that

the surface of sensor will not be exposed to the laser

beam.

Do not expose the device to high electromagnetic

radiation or extremely hot, cold, dusty or damp

environment.

Warnings Follow

these safeguards to

prevent serious injury

or death.

Cautions Follow these

precautions to prevent

potential injury or

material damage.

To avoid heat accumulation, good ventilation is

required for the operating environment.

Keep the camera away from liquid while in use for non-

water-proof device.

While in delivery, the camera shall be packed in its

original packing, or packing of the same texture.

Mark Description

Table 0-1 Mark Description

Mark

Description

DC Voltage

AC Voltage

1Introduction

1.1 Product Features

The main features are as follows:

High performance CMOS sensor

IR cut filter with auto switch

OSD menu with configurable parameters

Auto white balance

Internal synchronization

SMART IR mode

4 in 1 video output (switchable TVI/AHD/CVI/CVBS)

3-axis adjustment

1.2 Overview

1.2.1 Overview of Type I Camera

Bracket

Sun Shield

Lens

Video Cable

Power Cord

DC12

Switch Button

Figure 1-1 Overview of Type I Camera

Note:

Press and hold the switch button for 5 seconds to

switch the video output. Four kinds of video outputs

are available: TVI, AHD, CVI, and CVBS

1.2.2 Overview of Type II Camera

Camera

Enclosure

Mounting

Base Clip Plate

Power Cord

DC12VIN

Switch Button

Video Cable

Figure 1-2 Overview of Type II Camera

Note:

Press and hold the switch button for 5 seconds to

switch the video output. Four kinds of video outputs

are available: TVI, AHD, CVI, and CVBS

2Installation

Before you start:

Make sure that the device in the package is in good

condition and all the assembly parts are included.

Make sure that all the related equipment is power-off

during the installation.

Check the specification of the products for the

installation environment.

Check whether the power supply is matched with your

power output to avoid the damage.

Make sure the wall is strong enough to withstand three

times the weight of the camera and the mount.

If the wall is cement, insert expansion bolts before

installing the camera. If the wall is wooden, use self-

tapping screws to secure the camera.

If the product does not function properly, contact your

dealer or the nearest service center. Do NOT

disassemble the camera for repair or maintenance by

yourself.

2.1 Installation of Type I Camera

2.1.1 Ceiling Mounting without Junction Box

Before you start:

Both wall mounting and ceiling mounting are suitable for

the bullet camera. Ceiling mounting will be taken as an

example in this section. And you can take steps of ceiling

mounting as a reference for wall mounting.

Steps:

1. Paste the drill template (supplied) to the place where

you want to install the camera.

2. Drill the screw holes and the cable hole (optional) in

the ceiling according to the drill template.

Figure 2-1 Drill Template

Note:

Drill the cable hole, when adopting ceiling outlet to

route the cable.

3. Route the cables through the cable hole, or the side

opening.

4. Fix the camera to the ceiling with supplied screws.

Figure 2-2 Fix the Camera to the Ceiling

Note:

The supplied screw package contains self-tapping

screws, and expansion bolts.

For cement wall, expansion bolts are required to fix the

camera. For wooden wall, self-tapping screws are

required.

5. Connect the corresponding power cord, and video

cable.

6. Power on the camera to check whether the image on

the monitor is gotten from the optimum angle. If not,

adjust the surveillance angle.

R:360°

T:90°

P:360°

Figure 2-3 3-axis Adjustment

1) Loosen the No.① adjusting screw to adjust the

pan position [0° to 360°]. Tighten the No.①

adjusting screw.

2) Loosen the No.② adjusting screw to adjust the

tilting position [0° to 90°]. Tighten the No.②

adjusting screw.

3) Loosen the No.③ adjusting screw to adjust the

rotation position [0° to 360°]. Tighten the No.③

adjusting screw.

2.1.2 Ceiling Mounting with Junction Box

Before you start:

You need to purchase a junction box separately.

Both wall mounting and ceiling mounting are suitable

for the bullet camera. Ceiling mounting will be taken as

an example in this section. And you can take steps of

ceiling mounting as a reference for wall mounting.

Steps:

1. Paste the junction box’s drill template on the ceiling.

2. Drill screw holes and the cable hole (optional) in the

ceiling according to the holes of the drill template.

Figure 2-4 Drill Template

Note:

Drill the cable hole, when adopting ceiling outlet to

route the cable.

3. Take apart the junction box, and align the screw holes

of the bullet camera with those on the junction box’s

cover.

4. Fix the camera on the junction box’s cover.

Figure 2-5 Fix the Camera with the Junction Box

5. Attach the junction box’s body to the ceiling by

aligning the screw holes of the junction box.

6. Secure the junction box’s body with supplied screws

on the ceiling.

Screw

Junction

Box Body

Figure 2-6 Fix the Camera to the Ceiling

7. Route the cables through the cable hole, or the side

opening of the junction box.

8. Combine the junction box cover with its body.

Figure 2-7 Fix the Junction Box Cover back to its Body

9. Refer to step 6 of 2.1.1 Ceiling Mounting without

Junction Box to complete the installation.

2.2 Installation of Type II Camera

2.2.1 Ceiling Mounting without Junction Box

Before you start:

Both wall mounting and ceiling mounting are suitable for

the turret camera. Ceiling mounting will be taken as an

example in this section. And you can take steps of ceiling

mounting as a reference for wall mounting.

Steps:

1. Paste the drill template to the place where you want

to install the camera.

2. Drill the screw holes according to the drill template

and the cable hole (optional) in the ceiling.

Figure 2-8 Drill Template

Note:

Drill the cable hole, when adopting the ceiling outlet

to route the cable.

3. Loosen screws to remove the clip plate, and take out

the main body.

Clip Plate

Figure 2-9 Remove the Clip Plate

4. Fix the mounting base on the ceiling with supplied

screws.

Figure 2-10 Fix the Mounting Base on the Ceiling

Note:

The supplied screw package contains self-tapping

screws, and expansion bolts.

For cement wall, expansion bolts are required to fix the

camera. For wooden wall, self-tapping screws are

required.

5. Route the cables through the cable hole, or the side

opening.

6. Install the main body to the mounting base and insert

the clip plate.

Figure 2-11 Install the Turret Camera

7. Tighten the screws with the screw driver.

8. Connect the corresponding cables, such as power

cord, and video cable.

9. Power on the camera to check whether the image on

the monitor is gotten from the optimum angle. If not,

adjust the camera according to the figure below to get

an optimum angle.

Pan Position

[0°to 360°]

Tilt Position

[0°to 75°]

Rotation Position

[0°to 360°]

Figure 2-12 3-axis Adjustment

1). Hold the camera body and rotate the enclosure to

adjust the pan position [0° to 360°].

2). Move the camera body up and down to adjust the

tilt position [0° to 75°].

3). Rotate the camera body to adjust the rotation

position [0° to 360°].

2.2.2 Ceiling Mounting with Junction Box

Before you start:

You need to purchase a junction box separately.

Both wall mounting and ceiling mounting are suitable

for the turret camera. Ceiling mounting will be taken as

an example in this section. And you can take steps of

ceiling mounting as a reference for wall mounting.

Steps:

1. Paste the junction box’s drill template on the ceiling.

2. Drill screw holes and the cable hole (optional) in the

ceiling according to the holes of the drill template.

Screw

Hole

Cable

Hole

Figure 2-13 Drill Template of the Junction Box

Note:

Drill the cable hole, when adopting the ceiling outlet

to route the cable.

3. Refer to step 3 of 2.2.1 Ceiling Mounting without

Junction Box to take out the camera’s main body.

4. Take apart the junction box, and align the screw holes

of the camera with those on the junction box’s cover.

5. Fix the camera’s mounting base on the junction box’s

cover with three PM4 × 10 screws.

Figure 2-14 Secure Screws on Junction Box’s Cover

6. Secure the junction box’s body on the ceiling with four

PA4 × 25 screws.

Junction

Box Body

Figure 2-15 Secure the Junction Box’s Body on Ceiling

7. Combine the junction box cover with its body by

tightening four screws on junction box’s cover.

Figure 2-16 Fix the Junction Box

8. Repeat steps 5 to 9 of 2.2.1 Ceiling Mounting without

Junction Box to complete the installation.

3Menu Description

Purpose:

Call the menu by clicking the button on the PTZ

Control interface, or call preset No.95.

Steps:

1. Connect the camera with the TVI DVR, and the

monitor, shown as the figure 3-1.

Camera

TVI DVR

Monitor

Figure 3-1 Connection

2. Power on the analog camera, TVI DVR, and the

monitor to view the image on the monitor.

3. Click PTZ Control to enter the PTZ Control interface.

4. Call the camera menu by clicking button, or call

preset No. 95.

MAIN MENU

VIDEO

SETTINGS

FACTORY

DEFAULT

EXIT

EXPOSURE MODE

CONTRAST

SHARPNESS

SATURATION

3DNR

MIRROR

BACK

AGC

EXPOSURE

VIDEO

FORMAT

BACK

EXIT

SAVE & EXIT

WHITE

BALANCE

BRIGHTNESS

SAVE & EXIT

EXIT

SAVE & EXIT

DAY/NIGHT

MODE

BACK

EXIT

SAVE & EXIT

IMAGE

MODE

Figure 3-2 Main Menu Overview

5. Click the direction arrow to control the camera.

1). Click up/down direction button to select the item.

2). Click Iris + to confirm the selection.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HIK VISION Sicherheitskamera Handbücher

HIK VISION

HIK VISION DS-2CD7133-E Bedienungsanleitung

HIK VISION

HIK VISION DS-MH2211 Bedienungsanleitung

HIK VISION

HIK VISION 5 Inch Network High Speed Dome Bedienungsanleitung

HIK VISION

HIK VISION DS-2DF5220S Bedienungsanleitung

HIK VISION

HIK VISION DS-2XC6142FWD-IS Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD883F-E series Bedienungsanleitung

HIK VISION

HIK VISION PanoVu Series Bedienungsanleitung

HIK VISION

HIK VISION DS-2TD2167-7/PI Bedienungsanleitung

HIK VISION

HIK VISION DS-2CE56D0T-I2FB Bedienungsanleitung

HIK VISION

HIK VISION DS-PDCM15PF-IR Bedienungsanleitung

HIK VISION

HIK VISION iDS-2CD9396-BIS Bedienungsanleitung

HIK VISION

HIK VISION DS-2CC51A7N-VP Bedienungsanleitung

HIK VISION

HIK VISION DS-2CE16H1T-IT3Z Bedienungsanleitung

HIK VISION

HIK VISION DS-2CE16H5T-IT Bedienungsanleitung

HIK VISION

HIK VISION DS-2DP1636Z-D Bedienungsanleitung

HIK VISION

HIK VISION OMNI-IP KNC-p3BR IR Bedienungsanleitung

HIK VISION

HIK VISION HiWatch Series Installations- und Benutzerhandbuch

HIK VISION

HIK VISION DS-2DP0818ZIX Bedienungsanleitung

HIK VISION

HIK VISION DS-2TD2136-7 Bedienungsanleitung

HIK VISION

HIK VISION DS-2DYH2A0IXS-D Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD886BF-E Bedienungsanleitung

HIK VISION

HIK VISION DS-2CD2345G0P-I Bedienungsanleitung

HIK VISION

HIK VISION NETWORK CAMERA Bedienungsanleitung

HIK VISION

HIK VISION H264 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung