Hills NVC-BM1 Bedienungsanleitung

Network Camera Installation manual

NVC-BM1

NVC-DF1

NVC-DT1

NVC-DM1

V1.1

Congratulations on the purchase of your Hills Professional CCTV solution.

It’s important that you read this installation guide thoroughly before installation.

Thank you for choosing Hills.

Part no.

Model no.

Type

Model

S47092

NVC-DT1

Eyeball Dome camera

3MP IR Eyeball Camera (4mm)

S47091

NVC-DF1

Dome camera

3MP IR Dome Camera (4mm)

S47090

NVC-BM1

Bullet Camera

3MP IR Bullet Camera (4mm)

S47093

NVC-DM1

Mini Dome Camera

3MP IR Mini Dome Camera (2.8mm)

Checklist before you start:

All carton contents present and are in good conditions.

Ensure power supplies are off during installation.

Power supply voltage rating as specified in product specification.

Installation environment match is as specified.

Contact your dealer if product does not function properly. Do not attempt to repair yourself.

Wall or mounting platform is strong enough to withstand three times the weight of the camera.

For further information, including datasheets, FAQ and technical support please visit:

www.hills.com.au/videosecurity

Table of Contents:

1 NVC-DT1 - 3MP IR Eyeball Camera (4mm) --------------------------------------------------------- 4

1.1 Overview --------------------------------------------------------- 4

1.2 Installation --------------------------------------------------------- 5

2NVC-DF1 - 3MP IR Dome Camera (4mm) --------------------------------------------------------- 10

2.1 Overview --------------------------------------------------------- 10

2.2 Installation --------------------------------------------------------- 11

3NVC-BM1 - 3MP IR Bullet Camera (4mm) --------------------------------------------------------- 14

3.1 Overview --------------------------------------------------------- 14

3.2 Installation --------------------------------------------------------- 15

4NVC-DM1 - 3MP IR Mini Dome Camera (4mm) ----------------------------------------------------- 17

4.1 Overview --------------------------------------------------------- 17

4.2 Installation --------------------------------------------------------- 18

1.1 Overview

Figure 1-1 Product Structure Diagram

Table 1-1 Description

NO.

Description

Ethernet interface, PoE

Power Cable, 12V DC

Trim Ring

Camera

Note:

This camera supports Power over Ethernet (PoE), and the standard power supply is 12V DC.

If a power adaptor is used please make sure that it is compatible with the camera.

NVC-DT1 - 3MP IR Eyeball Camera (4mm)

1.2 Installation

Before you start, please verify the package contents are correct by checking the items against the

carton content list in the Quick Guide, and make sure all the components are included.

Note:

Please make sure that the wall is strong enough to withstand three times the weight of the

camera.

Wall mounting is recommended for this camera.

The wall must be strong enough to withstand more than three times the weight of the

camera.

Steps:

1. Dissembling the Trim Ring

1) Rotate the trim ring counterclockwise to remove it from the camera.

Figure 1-2 Dissembling the Trim Ring

2. Drill the Holes

1) Attach the supplied drill template to the position where you want to fix the camera.

2) Drill the screw holes and the cable hole on the ceiling according to the drill template.

Figure 1-3 The Drill Template

There are two cable outlet methods. One is to route the cables through the cable hole, and the

other is to route the cables through the side outlet shown below.

Figure 1-4 Side Outlet

Note:

Three side outlets on the enclosure are selectable, which makes routing the cables easier instead of

drilling a cable hole on the ceiling. Use a plier to remove the plastic and route the cables through

the hole.

3. Install the Camera

1). Connect the corresponding power/video cables.

2). Insert the supplied screws to the screw holes.

3). Tighten the screws to secure the camera to the ceiling.

Figure 1-5 Secure the Camera to the Ceiling

4. Adjust the Lens

1). Loosen the lock screw.

2). Rotate the enclosure to adjust the pan angle; rotate the camera to adjust the tilt angle.

3). Tighten the lock screw to clamp the lens.

Figure 1-6 Lock Screw

5. Install the Trim Ring

1). Attach the trim ring to the camera.

2). Rotate the trim ring clockwise to secure it to the camera.

Figure 1-7 Install the Trim Ring

2.1 Overview

Figure 2-1 Overview

Table 2-1 Physical Description

No.

Description

Mounting base

Horizontal stand

Vertical stand

Lower dome

Cables

Plate of infrared lamp

Lens

Black Liner

Safety rope

NVC-DF1 - 3MP IR Dome Camera (4mm)

2.2 Installation

Notes:

Do not place the camera in extremely hot or damp environment. To avoid heat accumulation,

good ventilation is required for a proper operating environment.

Ceiling mounting is recommended for this camera.

The ceiling must be thick enough to withstand more than three times the weight of the

camera.

Steps:

1. Drill the holes

Drill the screw holes on the ceiling with the supplied drilling template. If you need to route the

cables from the bottom of the camera, cut a cable hole in the ceiling.

Figure 2-2 Drill template

2. Install the camera

1) Loosen the set screws with a hex key (supplied) to remove the lower dome.

Figure 2-3 Remove the Lower Dome

Hole

Hole Hole

Ceiling Mounting

2) Fix the mounting base on the ceiling with screws.

Figure 2-4 Fix the Mounting Base

Note:

If required, you can route cables through the side opening on the side of the mounting base.

Figure 2-5 Side Opening

3. Adjust the Lens

Loosen the tilt lock screws, adjust the tilting position in a range of 65 degrees, and tighten

the tilt lock screws. Rotate the black liner to adjust the panning position in a range of 360

degrees until getting the desired surveillance angle.

Figure 2-6 Angle Adjusting

Side opening

Andere Handbücher für NVC-BM1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hills IP-Kamera Handbücher

Hills

Hills NVC-DT1 Bedienungsanleitung

Beliebte IP-Kamera Handbücher anderer Marken

FLIR

FLIR Exx series Bedienungsanleitung

Avigilon

Avigilon H4A-BO1-IR Bedienungsanleitung

Digital Watchdog

Digital Watchdog DWCA-C128-64 Bedienungsanleitung

ShareTech

ShareTech AV1 Bedienungsanleitung

Ezviz

Ezviz C6C Bedienungsanleitung

Melchioni

Melchioni UCAM 2015 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/ESD-4630 Bedienungsanleitung

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Bedienungsanleitung

Mitel

Mitel 6800i Series Service-Handbuch

Vitek

Vitek VTC-IR403-212NP Bedienungsanleitung

THOMSON

THOMSON DSC - 323W Bedienungsanleitung

AVer

AVer FB2027 Bedienungsanleitung

ENFORCER

ENFORCER EV-T5105-N2SQ Bedienungsanleitung

Wansview

Wansview NC543 Bedienungsanleitung

Eneo

Eneo MCB-64A0003M0A Bedienungsanleitung

deView electronics

deView electronics CBDNI36F Bedienungsanleitung

Swann

Swann SwannEye Bedienungsanleitung

LevelOne

LevelOne IP CamSecure Bedienungsanleitung