HIMO C20 Montageanleitung
Use Manual
Please read the instruction manual carefully before using your bike
Do not use the bike until you know its performance. Please keep the
instruction manual properly
XXXXXXXXXXXXXXX
Notes for using
According to the regulations on the implementation of the road traffic safety law of the People's Republic
of China, e-bike rider must be at least 16 years old.
When driving in the non-motorized lane, the maximum speed shall not exceed 15km/h;On roads
without non-motorized lanes, drive on the right side of the roadway.
Don't cause injury by lending your bike to someone who can't handle it.
Passengers or goods shall be carried according to laws and regulations.
Riding in rain and snow, the braking distance will be extended, pay attention to slow down;Avoid
traveling in bad weather such as heavy rain.
Before riding, check the braking system and clean the reflector to avoid blocking.
Obey traffic rules strictly
Safe of using the product
Please strictly abide by the traffic laws and regulations, prepare helmets, protective
equipment and other protective equipment before riding, and pay attention to driving
safety
Do not ride with one hand or two hands away from the handle.
Do not park in building doors, evacuation staircases, walkways, and safety exits.
Do not charge inside residential building and park, should be far from combustible when
charging, please charge according to regulation time, charging time should not be too long.
Correct use and maintenance of batteries, old batteries can not be disassembled without
authorization, should be organized by the professional departments recycling. Know how
to use charger and warning terms, use original charger.
When adjusting the saddle position, be careful not to expose the safety mark line of the
saddle tube.
Preparation before riding
Whether the power circuit and lighting are good.
Whether the front and rear brake lever are
good.
Whether the handlebars and front and
rear wheels are in a tight state.Whether the
tire pressure is normal.
Cross country and extreme
sports are prohibited
Bike coding position
1470×610×1095mm
965mm
21.6kg
25km/h
≈80km
≈55km
0.654kW·h/100km
≤100kg
31±0.5V
15±1A
10Ah
36V
M
+
25A fuse
+48V
+48V
+5V
-
ACC
TX
RX +5V
Electrical schematic
Motor
The controller
Overspeed alarm
The cathode
Overspeed warning signal
The cathode
The cathode
Power signal
Headlight signal
Booster sensor
Headlight
Display
Power interruption brake
The cathode
The signal of handle
The cathode
Note: long press the button for 3-5 seconds to turn on the
machine. After starting up,press the button again to turn
on the headlight and long press to turn off the machine.
Battery
Dimensions L*W*H
Front and rear wheel center distance
Max weight
Maximum design speed
Assisting rang
Electric range
Consumes electricity（100KM）
Loading weight
Motor Spec.
Under voltage protection
Over current protection
Controller Spec.
Battery Spec.
Main technical parameters of the bike
⑴ Under the condition of full power, loading weight is 75kg, the temperature is about 25℃, the environment of flat road is still
without wind, and the driving condition is measured at 15km/h uniform speed under the energy-saving mode. The actual
endurance will be different due to factors such as load, temperature, wind speed, road surface and operating.
Battery type
Capacity
Voltage
Lithium ion battery
250W
260r/min
36V
Brushless dc motor
Motor type
Rated power
Rated speed
Voltage
Knob
5A charging fuse
charging port of the battery.
Operation and use
Steps of using the pump
Folding steps
1. Open the seatclamp, pull out the
seat post
1.Push the handle switch upward and
open the handle outwards
2.Turn the handlebar to one side 3.Press the pedal inward 4.Flip the pedal and fold up
2.Unscrew the cap and extract the
cylinder assembly
3.Put the air nozzle firmly at the
valve nozzle
4.Flip the clasp 90 degrees hold the
cushion and start pumping
2 pcs
Press the power button, the light is blue, the power is about
70% to 100%
Press the power button, the light is green, the power is about
40-70%
Press the power button, the light is red, the power is about
10%-40%
If the light flashes, please charge in time
Check battery level
Taillight is designed as an independent switch.
Press the switch when using.
Prepare 1 suitable phillips screwdriver, 2 no. 7 batteries.
Remove the tail light, unscrew the front panel screw,
open the rear housing, and replace the batt
Buckle the rear shell, screw well, install it on the fixing ery.
plate, and finish replacing the battery.
Taillight opening and maintenance Change battery
Tail light
R/reflector
Switch
Cross screw driver
No. 7 battery
Charging cover
Battery button
Battery indicator light
Display and riding mode
Dashboard introduction
Switch button Speed
The speedometer
Real-time power
Riding mode (assist/medium speed/high speed)
Mode button
Mileage accumulated (switching)
Subtotal mileage (switching)
Electric riding Parking mode
Long press the switch for 3 seconds
to start the bike;
The first default gear is "ECO"
assisted riding mode;
This mode can be started by
pedaling for two laps.
Start the electric bike;
Press the mode button to switch the
mode to the gear of "MID" medium
speed electric riding mode;If the
speed exceeds 5km/h, turn the
handle to start the mode.
Press the mode button to switch the
mode to the gear of "HIGH" high-
speed electric riding mode;If the
speed exceeds 5km/h, turn the
handle to start the mode.
Long press the switch for 3
seconds to shut down the electric car;
Ride with pedal
Electric assist riding
Normal riding
In the startup state;
Press the mode button for 3
seconds to switch to park (P)
and open park mode.
Long press the mode button for 3 seconds
to close the parking mode.
In park mode, power is not
available in assist or electric ride
mode.
+
1-2
3-4
5-6
Transmission using
Transmission diagram
When using a gear system, try not to skip gears, which can easily damage the gear. It is not possible to change two gears at a time above, should be
a level of adjustment, can better protect the gear system.
Do not reverse the gear system when the bike stops running, or when it is going downhill. This will not only be bad for the gear system, but also
may cause accidents.
If it is their gear fault, or gear is not accurate situation, will affect the performance of the transmission, at this time should be timely to the
professional bike shop maintenance, in case of aggravation of the fault.
When using the transmission system, also pay attention to the following details
Gear SpeedPower
Relaxed Slow
Fast
ModerateModerate
Hard
To speed up, start with a lower gear and shift to a higher gear as you speed up
When going uphill, the speed will decrease and the gear will be lowered to maintain a certain
pedal strength
Downwind will speed up, increase gear to maintain a certain degree of pedal strength
The above is riding advice, according to personal habits to reasonable use of gear
Shift up
-Shift down
Gear pointer
When using a gear system, try not to skip gears, which can easily damage the gear. It is not possible to change two gears at a time above, should be
a level of adjustment, can better protect the gear system.
Battery instructions
Battery removal and installation
First place one end of the battery in the
slot
Aim the other end of the battery at the
charging port, press it gently and fasten
the latch
Key return, battery installed
Turn the key, the battery pops up,
and the battery is taken out
Battery charging
Open the soft cover on the side of the battery
The power supply pin of the charger is
inserted into the charging port of the battery,
and the power supply pin at the other end is
connected to the power supply
When charging, the charger status light is red
When the battery is fully charged, the charger
status light is green and the charging is finished
Unplug the charger for safekeeping and
close the soft cover
If the battery is charged in the bike, please turn off
the instrument power
The power supply plug
Power supply pin
lamp
Charging port
Soft cover
Key
Buckle
Plug
Frame charging port
Charging port
Before use, confirm that the battery model is the original battery of the whole bike, do not use any other brand of battery.
Check the appearance of lithium battery intact, no damage, leakage, heat and water, smoke and other obvious phenomena.
In order to ensure the safety of transportation, the battery's output power is about 30%. Due to the self-consumption during the transportation
and storage cycle, the battery is low or no electricity in the first use. This is a normal phenomenon.
About batteries
Note before use of lithium battery
The best operating environment is 10℃-45℃
At low temperature, available capacity of lithium battery will decrease to different degrees. The specific reference degree is as follows:
The available capacity is about 70% at -10℃, 85% at 0℃and 100% at 25℃.If the battery has odor, heat, deformation and other abnormal
conditions, please stop using immediately, away from the battery and contact the after-sales department.
The battery is not a part that can be repaired by the user. If there is any abnormal
phenomenon, please contact the after-sales department for maintenance.
Disassembling the battery without permission will not be covered by the three-pack
policy and may cause the battery to generate heat, smoke, fire or explosion.
Using the environment
Warning
Andere Handbücher für C20
1
Inhaltsverzeichnis
Andere HIMO Fahrrad Handbücher
