Hioki 3237 Bedienungsanleitung

INSTRUCTION MANUAL

For...は専用機種。複数の場合は「/」で区切る。不要の場合はとる。

形名を入力。複数の場合は「/」で区切る。

3237

3238

3239

品名を入力。

DIGITAL HiTESTER

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Contents

Introduction i

Inspection i

Safety Notes ii

Notes on Use v

Chapter Summary vi

Chapter 1 Overview 1

1.1 Product Overview 1

1.2 Major Features 1

1.3 Names and Functions of Parts 2

1.3.1 Front Panel 2

1.3.2 Rear Panel 6

Chapter 2 Installation and Preparation 7

2.1 Power Supply and Ground Connection 7

2.2 Test Lead/Clamp Sensor Connection 8

2.3 Power On/Off 9

2.4 Selection of Power-supply Frequency 10

Chapter 3 Measurement Procedure 11

3.1 Voltage Measurement 12

3.1.1 DC Voltage Measurement 12

3.1.2 AC Voltage Measurement 12

3.2 2-Terminal Resistance Measurement 13

3.2.1 Resistance Measurement (2-Terminal) 13

3.2.2 Low-power Resistance Measurement (2-Terminal) 14

3.3 4-Terminal Resistance Measurement 15

3.3.1 Resistance Measurement (4-Terminal, on 3239 only) 15

3.3.2 Low-power Resistance Measurement

(4-Terminal, on 3239 only) 16

3.4 Continuity Test 16

3.5 Diode Test 17

3.6 Frequency Measurement (3238/39) 18

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

3.7 Current Measurement (3238/39) 19

3.7.1 DC Current Measurement 19

3.7.2 AC Current Measurement 19

3.8 Clamp Current Measurement 20

3.8.1 DC Clamp Current Measurement

(9277/9278/9279/3284/3285) 21

3.8.2 AC Clamp Current Measurement 22

Chapter 4 Basic Functions 23

4.1 Selection of Measurement Range 23

4.2 Switching of Sampling Period 23

4.3 Zero Adjust function 24

4.4 Average function 25

4.5 Trigger Function 26

4.5.1 Setup for Trigger mode 26

4.5.2 External Trigger 26

4.5.3 Trigger Delay 27

4.5.4 Trigger System 29

Chapter 5 Other Functions 31

5.1 Comparator Function 31

5.2 Comparator Buzzer Sound 34

5.3 Panel Save Function 35

5.4 Panel Load Function 36

5.5 Key Operation Sound 37

5.6 Key Lock Function 38

5.7 Remote Function 39

5.8 System Reset 40

5.9 Measurement States and Effective Keys 42

Chapter 6 External Control Terminal/

External output terminal 43

6.1 Explanation of Signal Wires 44

6.2 Timing Chart 46

6.3 Internal Circuit Configuration 48

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Chapter 7 RS-232C Interface 49

7.1 Preparing for Data Transfer 51

7.2 Communication 53

7.3 Command Code Table 62

7.3.1 Common Command 62

7.3.2 Specific Command 63

7.4 Command Reference 69

7.4.1 Explanation of Command Reference 69

7.4.2 Common Command Messages 70

7.4.3 Specific Command Messages 75

7.5 Initialized Item List 99

7.6 Notes on RS-232C Interface 99

7.7 Compatibility with the ADVANTEST Digital

Multimeter 100

7.8 Sample Program 102

Chapter 8 GP-IB Interface(3237-01/3238-01/3239-01) 103

8.1 Preparing for Data Transfer 105

8.2 Communication 107

8.3 GP-IB Command 116

8.4 Notes of the GP-IB 117

Chapter 9 Printer Interface 119

9.1 Setup for Interface 120

9.2 Setup for Printer 121

9.3 Printer Connection Method 123

9.4 Sample Prints 124

Chapter 10 Specifications 125

10.1 General Specifications 125

10.2 Accuracy 127

10.2.1 Accuracy of the 3237 127

10.2.2 Accuracy of the 3238 133

10.2.3 Accuracy of the 3239 140

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Chapter 11 Maintenance and Service 147

11.1 A-Terminal Fuse Replacement (3238/39) 147

11.2 Power Supply Fuse Replacement 148

11.3 Cleaning 149

11.4 Service 150

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

_____________________________________________________________________________________________

______________________________________________________________________________________________

NOTE Before using the product, make sure that the insulation on the probes is undamaged

and that no bare conductors are improperly exposed. Using the product in such

conditions could cause an electric shock, so contact your dealer or Hioki

resentative for re

air.

Introduction

Inspection

Thank you for purchasing the HIOKI "3237, 3238, 3239 DIGITAL

HiTESTER."

To obtain maximum performance from the product, please read this manual

first, and keep it handy for future reference.

When you receive the product, inspect it carefully to ensure that no damage

occurred during shipping. In particular, check the accessories, panel

switches, and connectors. If damage is evident, or if it fails to operate

according to the specifications, contact your dealer or Hioki representative.

Accessories

9170-10 TEST LEAD 1

Instruction Manual 1

Power cord 1

Spare fuse 0.5 A (for 100 V, 120 V), 0.25 A (for 220 V, 240 V)

2 A (for the 3238/39) 1

Before using the product the first time, verify that it operates normally to

ensure that the no damage occurred during storage or shipping. If you find

any damage, contact your dealer or Hioki representative.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

_____________________________________________________________________________________________

______________________________________________________________________________________________

WARNING

This instrument is designed to comply with IEC 61010 Safety Standards,

and has been thoroughly tested for safety prior to shipment. However,

mishandling during use could result in injury or death, as well as

damage to the instrument. Be certain that you understand the

instructions and precautions in the manual before use. We disclaim any

responsibility for accidents or injuries not resulting directly from

instrument defects.

The symbol printed on the product indicates that the user should

refer to a corresponding topic in the manual (marked with the

symbol) before using the relevant function.

In the manual, the symbol indicates particularly important

information that the user should read before using the product.

Indicates that dangerous voltage may be present at this terminal.

Indicates a double-insulated device.

Indicates a fuse.

Indicates AC (Alternating Current).

Indicates DC (Direct Current).

Indicates both DC (Direct Current) and AC (Alternating Current).

Indicates a grounding terminal.

Indicates the ON side of the power switch.

Indicates the OFF side of the power switch.

DANGER

Indicates that incorrect operation presents an extreme hazard that

could result in serious injury or death to the user.

WARNING

Indicates that incorrect operation presents a significant hazard that

could result in serious injury or death to the user.

CAUTION Indicates that incorrect operation presents a possibility of injury to

the user or damage to the product.

NOTE Advisory items related to performance or correct operation of the

product.

Safety Notes

This manual contains information and warnings essential for safe operation

of the product and for maintaining it in safe operating condition. Before

using the product, be sure to carefully read the following safety notes.

The following symbols in this manual indicate the relative importance of

cautions and warnings.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

iii

_____________________________________________________________________________________________

______________________________________________________________________________________________

CAT I Secondary electrical circuits that are connected

to a wall outlet through a transformer or similar

device.

CAT II Primary electrical circuits in equipment connected to

a wall outlet via a power cord (portable tools,

household appliances, etc.)

CAT III Primary electrical circuits of heavy equipment (fixed

installations) connected directly to the distribution

panel, and feeders between the distribution panel

and outlets.

CAT IV The circuit from the service drop to the service

entrance, then to the power meter and to the primary

overcurrent protection device.

Overvoltage Categories

This product conforms to the safety requirements for CAT II measurement

products.

To ensure safe use of measurement, IEC 60664 establishes safety level

standards for different locations, classified as CAT I through CAT IV, and

called overvoltage categories. These are defined as follows.

Higher-numbered categories correspond to electrical environments with

greater momentary energy, so a measurement device designed for CAT III

environments can endure greater momentary energy than a device designed

for CAT II. Use of a lower category product in a higher category

environment could result in a severe accident and must be carefully avoided.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

_____________________________________________________________________________________________

______________________________________________________________________________________________

f.s. (maximum display or scale value, or length of scale)

Signifies the maximum display (scale) value or the length of the scale

(in cases where the scale consists of unequal increments or where the

maximum value cannot be defined).

In general, this is the range value (the value written on the range

selector or equivalent) currently in use.

rdg. (displayed or indicated value)

This signifies the value actually being measured, i.e., the value that is

currently indicated or displayed by the measuring instrument.

dgt. (resolution)

Signifies the smallest display unit on a digital measuring instrument,

i.e., the value displayed when the last digit on the digital display is

"1".

Accuracy The specifications in this manual include figures for "measurement accuracy"

when referring to digital measuring instruments, and for "measurement

tolerance" when referring to analog instruments.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

_____________________________________________________________________________________________

______________________________________________________________________________________________

WARNING

To avoid electric shock, do not allow the product to get wet, and do

not use it when your hands are wet.

Do not use the product where it may be exposed to corrosive or

combustible gases. The product may be damaged or cause an

explosion.

To avoid electric shock, be sure to connect the protective ground

terminal to a grounded conductor.

CAUTION Do not store or use the product where it could be exposed to direct

sunlight, high temperature or humidity, or condensation. Under such

conditions, the product may be damaged and insulation may deteriorate so

that it no longer meets specifications.

This product is not designed to be entirely water- or dust-proof. To avoid

damage, do not use it in a wet or dusty environment.

Do not use the product near a device that generates a strong

electromagnetic field or electrostatic charge, as these may cause

erroneous measurements.

To avoid damage to the product, protect it from vibration or shock during

transport and handling, and be especially careful to avoid dropping.

Notes on Use

In order to ensure safe operation and to obtain maximum performance from

the unit, observe the cautions listed below.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Andere Handbücher für 3237

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hioki Prüfgeräte Handbücher

Hioki

Hioki 3660 Bedienungsanleitung

Hioki

Hioki HiTESTER 3540 Bedienungsanleitung

Hioki

Hioki 3288 Bedienungsanleitung

Hioki

Hioki FT6380-50 Bedienungsanleitung

Hioki

Hioki 3804-50 Bedienungsanleitung

Hioki

Hioki 3555 Bedienungsanleitung

Hioki

Hioki 3285-20 Bedienungsanleitung

Hioki

Hioki 3008 Bedienungsanleitung

Hioki

Hioki FT3405 Bedienungsanleitung

Hioki

Hioki SS7012 Bedienungsanleitung

Hioki

Hioki SS9000 Bedienungsanleitung

Hioki

Hioki 3801 Bedienungsanleitung

Hioki

Hioki BT5525 Gebrauchsanweisung

Hioki

Hioki ST5520-01 Bedienungsanleitung

Hioki

Hioki MO HiTESTER 3452 Bedienungsanleitung

Hioki

Hioki 3154 Bedienungsanleitung

Hioki

Hioki Power HiTester 3193 Bedienungsanleitung

Hioki

Hioki DT4261 Bedienungsanleitung

Hioki

Hioki 3415-01 Bedienungsanleitung

Hioki

Hioki 8807-51 Bedienungsanleitung

Hioki

Hioki IR3455 Bedienungsanleitung

Hioki

Hioki L2020 Bedienungsanleitung

Hioki

Hioki FT6031-03 Bedienungsanleitung

Hioki

Hioki 3245-60 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung

Ritmix

Ritmix RAT-701 Bedienungsanleitung