Hioki 3555 Bedienungsanleitung
INSTRUCTION MANUAL
For...は専用機種。複数の場合は「/」で区切る。
不要の場合はとる。
形名を入力。 複数の場合は「/」で区切る。
3555
品名を入力。
BATTERY HiTESTER
http://www.911618.com/
http://www.911618.com/dianchiceshiyi/HIOKI-3555/
http://www.911618.com/jishuwenzhang/HIOKI-3555/
Contents
Introduction i
Inspection i
Safety ii
Precautions v
Organization of This Manual viii
Chapter 1 Overview 1
1.1 Product Overview 1
1.2 Features 1
Chapter 2 Names and Functions of Parts 3
Chapter 3 Specifications 9
3.1 General Specification 9
3.2 Measurement Range 12
3.2.1 Maximum Input Voltage 13
3.2.2 Dielectric Strength 14
Chapter 4 Standard Measurement 15
4.1 Preparing for Measurement 15
4.2 Measurement 16
Chapter 5 Advanced Measurement Functions 21
5.1 Comparator Function 21
5.1.1 What is the Comparator Function? 21
5.1.2 Changing the Comparator Settings 22
5.1.3 Comparator Decision Result Table 27
5.1.4 Switching the Comparator On and Off 28
5.1.5 Changing the Comparator Number 29
5.2 Beeper On/Off Function 29
5.3 Hold Function 30
5.4 Zero Adjust Function 30
5.5 Battery Low Warning 32
5.6 Auto Power Off 33
5.7 AC Four-Terminal Method 35
Chapter 6 Maintenance 37
6.1 Troubleshooting 37
6.2 Message Reference 38
6.3 Cleaning 39
i
――――――――――――――――――――――――――――――――――――――
Inspection
――――――――――――――――――――――――――――――――――
Introduction
Inspection
Thank you for purchasing the HIOKI "3555 BATTERY
HiTESTER." To obtain maximum performance from the
instrument, please read this manual first, and keep it
handy for future reference.
When you receive the instrument, inspect it carefully to
ensure that no damage occurred during shipping. In
particular, check the accessories, panel switches, and
connectors. If damage is evident, or if it fails to operate
according to the specifications, contact your dealer or
Hioki representative.
Accessories
9461 PIN TYPE LEAD
Six LR6 alkaline batteries
Instruction Manual
Shipping
Use the original packing materials when reshipping the
instrument, if possible.
ii
――――――――――――――――――――――――――――――――――――――
Safety
――――――――――――――――――――――――――――――――――
DANGER This instrument is designed to comply with IEC 61010
Safety Standards, and has been thoroughly tested for
safety prior to shipment. However, mishandling
during use could result in injury or death, as well as
damage to the instrument. Be certain that you
understand the instructions and precautions in the
manual before use. We disclaim any responsibility for
accidents or injuries not resulting directly from
instrument defects.
･The symbol printed on the instrument
indicates that the user should refer to a
corresponding topic in the manual (marked
with the symbol) before using the relevant
function.
･In the manual, the symbol indicates
particularly important information that the
user should read before using the instrument.
Indicates DC (Direct Current).
Indicates the ON side of the power switch.
Indicates the OFF side of the power switch.
Safety
Safety symbols
This manual contains information and warnings essential
for safe operation of the instrument and for maintaining
it in safe operating condition. Before using the
instrument, be sure to carefully read the following safety
notes.
iii
――――――――――――――――――――――――――――――――――――――
Safety
――――――――――――――――――――――――――――――――――
DANGER Indicates that incorrect operation presents an
extreme hazard that could result in serious
injury or death to the user.
WARNING Indicates that incorrect operation presents a
significant hazard that could result in serious
injury or death to the user.
CAUTION Indicates that incorrect operation presents a
possibility of injury to the user or damage to the
instrument.
NOTE Indicates advisory items related to performance
or correct operation of the instrument.
The following symbols in this manual indicate the relative
importance of cautions and warnings.
iv
――――――――――――――――――――――――――――――――――――――
Safety
――――――――――――――――――――――――――――――――――
Measurement categories (Overvoltage categories)
This instrument complies with CAT I safety requirements.
To ensure safe operation of measurement instruments, IEC
61010 establishes safety standards for various electrical
environments, categorized as CAT I to CAT IV, and called
measurement categories. These are defined as follows.
CAT I : Secondary electrical circuits connected to an AC
electrical outlet through a transformer or similar
device.
CAT II : Primary electrical circuits in equipment connected
to an AC electrical outlet by a power cord
(portabletools,household appliances, etc.)
CAT III : Primary electrical circuits of heavy
equipment (fixed installations) connected directly
to the distribution panel, and feeders from the
distribution panel to outlets.
CAT IV : The circuit from the service drop to the service
entrance, and to the power meter and primary
overcurrent protection device (distribution panel).
Higher-numbered categories correspond to electrical
environments with greater momentary energy. So a
measurement device designed for CAT III environments can
endure greater momentary energy than a device designed
for CAT II.
Using a measurement instrument in an environment
designated with a higher-numbered category than that for
which the instrument is rated could result in a severe
accident, and must be carefully avoided.
Never use a CAT I measuring instrument in CAT II, III, or
IV environments.
The measurement categories comply with the Overvoltage
Categories of the IEC60664 Standards.
v
――――――――――――――――――――――――――――――――――――――
Precautions
――――――――――――――――――――――――――――――――――
DANGER The floating voltage between input terminals and
ground is 60 V AC/DC. Do not attempt to measure
voltages exceeding 60 V with respect to ground. This
could result in injury or damage to the instrument.
When measuring batteries, always ensure sufficient
ventilation. Sometimes sparks may occur when the
test leads are connected to batteries, which can ignite
any accumulated inflammable gases such as hydrogen.
WARNING Before using the instrument, make sure that the
insulation on the test leads is undamaged and that no
bare conductors are improperly exposed. Using the
instrument in such conditions could cause an electric
shock, so contact your dealer or Hioki representative
for replacements (Model 9461, Model 9287-10).
Precautions
Follow these precautions to ensure safe operation and to
obtain the full benefits of the various functions.
Preliminary Check
Before using the instrument the first time, verify that it
operates normally to ensure that the no damage occurred
during storage or shipping. If you find any damage,
contact your dealer or Hioki representative.
vi
――――――――――――――――――――――――――――――――――――――
Precautions
――――――――――――――――――――――――――――――――――
WARNING Be sure to connect the SOURCE and SENSE terminals
correctly. See Section 4.2, "Measurement" for details
of the connections.
To avoid injury or damage to the instrument, do not
attempt to measure AC voltage, or DC voltage
exceeding 50 V.
50 VDC max
Do not apply a voltage between the SOURCE(+) and
SENSE(+) or SOURCE(-) and SENSE(-) terminals. This
could result in damage to the instrument.
CAUTION ･This instrument is not designed to be entirely water- or
dust-proof. To avoid damage, do not use it in a wet or
dusty environment.
･Do not store or use the instrument where it could be
exposed to direct sunlight, high temperature or
humidity, or condensation. Under such conditions, the
instrument may be damaged and insulation may
deteriorate so that it no longer meets specifications.
･Do not use the instrument near a source of strong
electromagnetic radiation, or near a highly electrically
charged object. These may cause a malfunction.
vii
――――――――――――――――――――――――――――――――――――――
Precautions
――――――――――――――――――――――――――――――――――
NOTE ･Correct measurement may be impossible in the presence
of strong magnetic fields, such as near transformers
and high-current conductors, or in the presence of
strong electromagnetic fields such as near radio
transmitters.
･For safety reasons, when taking measurements, only
use the 9461 PIN TYPE LEAD provided with the
instrument, or the optional 9287-10 CLIP TYPE LEAD.
Service
･When sending the instrument for repair, remove the
batteries and pack carefully to prevent damage in transit.
Include cushioning material so the instrument cannot
move within the package. Be sure to include details of the
problem. Hioki cannot be responsible for damage that
occurs during shipment.
Inhaltsverzeichnis
Andere Hioki Prüfgeräte Handbücher
Hioki
Hioki FT6381 Bedienungsanleitung
Hioki
Hioki 3257-50 Bedienungsanleitung
Hioki
Hioki SS7012 Bedienungsanleitung
Hioki
Hioki FT6380-50 Bedienungsanleitung
Hioki
Hioki 3554 Bedienungsanleitung
Hioki
Hioki IR4059 Bedienungsanleitung
Hioki
Hioki 3159 Bedienungsanleitung
Hioki
Hioki FT6380 Bedienungsanleitung
Hioki
Hioki BT3564 Bedienungsanleitung
Hioki
Hioki FT6031 Bedienungsanleitung
Hioki
Hioki 3665-20 Bedienungsanleitung
Hioki
Hioki 3118 Bedienungsanleitung
Hioki
Hioki 3291-50 Bedienungsanleitung
Hioki
Hioki 3173 Bedienungsanleitung
Hioki
Hioki 3636-20 Bedienungsanleitung
Hioki
Hioki FT3470-51 Bedienungsanleitung
Hioki
Hioki 3561 Bedienungsanleitung
Hioki
Hioki 3541 Bedienungsanleitung
Hioki
Hioki FT3151 Bedienungsanleitung
Hioki
Hioki 3455 Bedienungsanleitung
Beliebte Prüfgeräte Handbücher anderer Marken
SMART
SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung
Agilent Technologies
Agilent Technologies BERT Serial Bedienungsanleitung
Agilent Technologies
Agilent Technologies N3280A Bedienungsanleitung
Vernier
Vernier Go Direct Voltage Bedienungsanleitung
Lifeloc
Lifeloc R.A.D.A.R. Bedienungsanleitung
Fluke
Fluke T5-600 Bedienungs- und Montageanleitung
PCB Piezotronics
PCB Piezotronics 8159-0112A Bedienungsanleitung
BW Technologies
BW Technologies MicroDock II Bedienungsanleitung
Sun Nuclear
Sun Nuclear 1027 Bedienungsanleitung
Biomark
Biomark HPR LITE READER Bedienungsanleitung
Ashcroft
Ashcroft ATE-100 Bedienungsanleitung
Rohde & Schwarz
Rohde & Schwarz RTA4000 Bedienungsanleitung