Hioki 8807-51 Bedienungsanleitung

INSTRUCTION MANUAL

8807-51

8808-51

MEMORY HiCORDER

HARMONIC WAVE

ANALYSIS FUNCTION

Contents

1. General Description 1

2. Setup Procedures 2

3. Basic Setting Items 3

3.1 Function Setting 3

3.2 Measurement Target Setting 3

4. Analog Input Channel Setting 5

4.1 Waveform Display Color Setting 5

4.2 Input Type Setting 6

4.3 Vertical Axis Range Setting 7

4.4 Scaling Setting 8

4.5 Scale Conversion Rate Setting 9

4.6 Line Connection & Level Check 11

4.7 DMM Function 13

5. Instantaneous Analysis Mode 15

5.1 Analyses and Display Screens 15

5.2 Basic Item Setting 21

5.3 Cursor Operation 27

5.4 Analysis Example 1: Simultaneous Instantaneous

Analysis of Two 100-VAC Single-Phase 2-Wire Lines 28

5.5 Analysis Example 2: Instantaneous Analysis of 200-VAC

3-Phase 3-Wire Line 33

6. Time-Series Analysis Mode 35

6.1 Basic Item Setting 35

6.2 Analysis Item Setting 41

6.3 Cursor Operations 45

6.4 Waveform Scrolling 46

6.5 Input Setting in Waveform Display Screen 47

6.6 Over-Range Check Function 48

6.7 Analysis Example: Time-Series Analysis of 100-VAC

Single-Phase 3-Wire Line 49

7. Triggers for Harmonic Wave Analysis Function 52

7.1 Basic Trigger Setting Items and Setting Methods 52

7.2 Harmonic Wave Trigger 55

8. Printer Operations 59

8.1 Recording on Printer 59

9. PC Card 62

9.1 Input of File Name 62

9.2 Text File Internal Format 63

9.3 Examples of Stored Files 64

10. Characteristics of CLAMP ON PROBES

(Reference Information) 66

Index INDEX 1

_____________________________________________________________________________________________

______________________________________________________________________________________________

1. General Description

The harmonic wave analysis function is designed exclusively for use with the

8807-51/8808-51 MEMORY HiCORDER.

For detailed information on the product and product functions, please refer

to the manual for the main unit.

Features

(1) A range of harmonic wave analysis functions for commercial

power supplies

The 8807-51 is designed for analysis of single-phase 2-wire lines, while the

8808-51 is intended for analysis of single-phase 2-wire lines, single-phase 2-

wire lines of two different systems, single-phase 3-wire lines, and 3-phase 3-

wire lines.

The function measures power supplies with a fundamental frequency ranging

from 45 to 65 Hz.

(2) Fast Fourier transform in accordance with frequency

512 data points sampled at a rate of 400 kS/s are extracted for calculations.

(3) Two analysis modes to match specific applications

Instantaneous analysis mode for analysis of instantaneous waveforms during

measurement.

Time-series analysis mode for recording and analyzing analysis data as time-

series data.

(4) Extensive analysis items

Six types of analysis of harmonic waves of all degrees rms value, content

ratio, phase angle, active power, power content ratio, and power phase angle

and calculations of total rms value, total distortion, active power, reactive

power, apparent power, and power factor are available.

(5) Instantaneous analysis mode

Displays analysis results as spectral graphs or with numeric values, and

stores result data.

Displays all harmonic wave components from 1st degree to 40th degree on a

single screen.

(6) Time-series analysis mode

Data on 20 phenomena over a period of up to 30 days, or data on four

phenomena over a maximum of 150 days, can be stored in memory.

Four phenomena can be recorded in an overlapping manner on a single time

axis to allow an easy grasp of the interrelationships among phenomena.

The time axis can be set in seven levels from 5 min/DIV to 12 h/DIV.

Smoothing function for cancellation of unexpected phenomena

Pre-trigger function for observation of the signal prior to a trigger

(7) Harmonic wave trigger function

The trigger can be tripped for rms value, content ratio, all degrees power,

power content ratio, power phase angle, total rms value, and any type of

distortion of a selected harmonic wave component.

_____________________________________________________________________________________________

______________________________________________________________________________________________

1 Basic Settings (Page)

1. Selecting the Harmonic Wave Function 3

2. Selecting the Power Supply Line 3

2 Detailed Input Settings

1. Waveform Display Color Setting 5

2. Input Type Setting 6

3. Vertical Axis Range Setting 7

4. Scaling Setting 8

5. Line Connection & Level Check Setting 11

Application: Trigger Setting 52

3 Instantaneous Analysis

1. Basic Settings 21

2. Reading Display with Cursor 27

Analysis Example 1:

Instantaneous Analysis of 100-VAC Single-Phase

2-Wire Line 28

Analysis Example 2:

Instantaneous Analysis of 200-VAC 3-Phase

3-Wire Line 33

Time-Series Analysis

1. Basic Settings 35

2. Analysis Item Setting 41

3. Reading Display with Cursor, and Waveform

Scrolling 45

Analysis Example 1:

Time-Series Analysis of 100-VAC Single-Phase

3-Wire Line 49

4 Data Printing and Saving

Printer Recording Setting 59

Using a PC Card 62

Entering a File Name 62

2. Setup Procedures

(8) Scaling function

Easy input setting for measurement using a clamp ammeter

(9) Equipped with anti-aliasing filter

Built-in low-pass filter prevents return distortion by eliminating all

frequencies other than measurement targets.

(10) Over-range check function

Automatically switches to a lower sensitivity range when an input waveform

exceeds the maximum input voltage.

Setting examples

Q&A

Method of selecting the range

when measuring commercial

power supplies 7

Q&A

Method of selecting the range

when using the 9018-10 CLAMP

ON PROBE 7

Q&A

Method of scaling with a

combination of the 9020 CLAMP

ON ADAPTER and 9018-10

CLAM ON PROBE 9

Q&A

Current measurement using a

combination of the 9277

UNIVERSAL CLAMP ON CT

and 9555 SENSOR UNIT 10

_____________________________________________________________________________________________

3.2 Measurement Target Setting

______________________________________________________________________________________________

3.1 Function Setting

3.2 Measurement Target Setting

UNIQUE

(Independent

channels)

Conducts power analysis only when

odd-number channel receives

voltage input and even-number

channel receives current input

(clamp). (Any input type can be

set.)

1P2W

Single-phase

2-wire

Analyzes single-phase 2-wire line.

Perform the setting so that odd-

number channels receive voltage

input and even-number channels

receive current input (clamp). (The

8808-51 can analyze two single-

phase 2-wire lines simultaneously.)

1P3W

(Single-phase

3-wire)

Analyzes single-phase 3-wire line.

(8808-51 only)

3P3W

(3-phase 3-

wire)

Analyzes 3-phase 3-wire line.

(8808-51 only)

3. Basic Setting Items

The 8807-51 and 8808-51 each provide a total of four functions.

To use the harmonic wave analysis function, follow the procedures given

below.

Setting Screen SET >>STATUS(1/4)/ CHANNEL(2/4)/ TRIGGER(3/4)/ ANALYZE(4/4)

1. Move the flashing cursor to the location shown

in the diagram.

2. Using the buttons, select HARM.

This screen is used to select the power supply type to be measured.

Setting Screen SET >>CHANNEL(2/4)

1. Move the flashing cursor to Wiring.

2. Make a setting using the buttons.

_____________________________________________________________________________________________

3.2 Measurement Target Setting

______________________________________________________________________________________________

Single-phase 2-wire

LoadSource

CH1 CH2

8807-51

HL HL

CH1 CH2 CH3 CH4

8808-51

Position the clamp with the current direction

indicator pointing toward the load side.

Source Source

Load Load

Single-phase 3-wire

8808-51 only

HLHL

Source Load

CH1 CH2 CH3 CH4

8808-51

3-phase 3-wire

8808-51 only (3-phase 3-wire, 2-power meter method)

HLHL

Source Load

CH1 CH2 CH3 CH4

8808-51

Source

Load

For example, when using a HIOKI clamp on probe, the clamping method should be as shown below.

If the clamp on probe is faced in the opposite direction, the phase will shift 180 degrees from the actual

value.

Source

Load

9018-10 9132-10

NOTE The direction of connection for the 9132-10 is opposite from the 9018-10.

_____________________________________________________________________________________________

4.1 Waveform Display Color Setting

______________________________________________________________________________________________

4.1 Waveform Display Color Setting

List OFF Does not display

waveform.

Red/Green Prints waveform at

standard print density.

Yellow/Light

Blue

Prints waveform at low

print density.

Blue/Gray Prints waveform at high

print density.

4. Analog Input Channel Setting

In instantaneous analysis mode, you can select the color of the displayed

waveform.

Setting Screen SET >>CHANNEL(2/4)

1. Move the flashing cursor to the location next to

the channel to be set, as shown in the diagram.

2. Make a setting using the buttons.

When the 8992 PRINTER UNIT is used to print a

waveform, the three print densities are used to

represent the selected waveform display color (6

colors).

Print density has no effect in real-time printing.

_____________________________________________________________________________________________

4.2 Input Type Setting

______________________________________________________________________________________________

4.2 Input Type Setting

(*)When a 3283, 3284, or 3285 CLAMP ON

HiTESTER is selected, power analysis

(harmonic wave active power, harmonic wave

power content ratio, harmonic wave power

phase angle, active power, apparent power,

reactive power, power factor) cannot be

performed due to the phase characteristics.

If the 3283, 3284, or 3285 is selected, the

following warning message is displayed when

power analysis begins.

"Warning 635: 3283,3284,3285 can't analyze

power."

VOLT For direct input of voltage or when using a

general-purpose clamp probe

9018 (Current measurement)

When using a 9018-10 CLAMP ON PROBE

9132 (Current measurement)

When using a 9132-10 CLAMP ON PROBE

3283(*) (Leakage current measurement)

When using a 3283 CLAMP ON LEAK

HiTESTER

3284(*) (Current measurement)

When using a 3284 CLAMP ON AC/DC

HiTESTER

3285(*) (Current measurement)

When using a 3285 CLAMP ON AC/DC

HiTESTER

9322 (High voltage measurement)

When using a 9322 DIFFERENTIAL PROBE

NOTE Precautions for measuring current using a HIOKI CLAMP ON PROBE/CLAMP ON

HiTESTER

Set the same measurement range for the 8807-51/8808-51 and the clamp.

Accurate measurements are not possible if improper ranges are set.

When using the 3283, 3284 or 3295 CLAMP ON HiTESTER for current

measurement, press the OUTPUT button on the 3283/3284/3285 unit and set to

MON

(

waveform out

ut: AC

)

The input type must be set for each analog input channel.

Voltage and current in combination with the HIOKI Clamp Sensor can be

measured.

When the name of clamp is selected, measurements are automatically

converted to current values and displayed.

Setting Screen SET >>CHANNEL(2/4)

1. Move the flashing cursor to INPUT.

2. Make a setting using the buttons.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hioki Prüfgeräte Handbücher

Hioki

Hioki P2000 Bedienungsanleitung

Hioki

Hioki FT3470-51 Bedienungsanleitung

Hioki

Hioki MEMORY HiCORDER 8855 Gebrauchsanweisung

Hioki

Hioki 3291-50 Bedienungsanleitung

Hioki

Hioki IM9201 Bedienungsanleitung

Hioki

Hioki 3156 Bedienungsanleitung

Hioki

Hioki ST5540 Bedienungsanleitung

Hioki

Hioki 3169-21 Gebrauchsanweisung

Hioki

Hioki 3145 Bedienungsanleitung

Hioki

Hioki 3665-20 Bedienungsanleitung

Hioki

Hioki 3159 Bedienungsanleitung

Hioki

Hioki BT5525 Gebrauchsanweisung

Hioki

Hioki FT6380-50 Bedienungsanleitung

Hioki

Hioki SS9000 Bedienungsanleitung

Hioki

Hioki FT3151 Bedienungsanleitung

Hioki

Hioki IR4057-50 Bedienungsanleitung

Hioki

Hioki 3158 Bedienungsanleitung

Hioki

Hioki Analog MO HiTESTER Series Bedienungsanleitung

Hioki

Hioki IR4055 Bedienungsanleitung

Hioki

Hioki FT6380 Bedienungsanleitung

Hioki

Hioki 9699 Bedienungsanleitung

Hioki

Hioki FT4310 Bedienungsanleitung

Hioki

Hioki 3280-10 Bedienungsanleitung

Hioki

Hioki BT5525 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung