Hirschmann SPIDER Premium Line Bedienungsanleitung

Installation SPIDER-PL

Release

08/2016

Technical support

https://hirschmann-support.belden.eu.com

User Manual

Installation

Industrial Ethernet Rail Switch

SPIDER Premium Line

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

SPIDER-PL

Installation SPIDER-PL

Release

08/2016 3

Contents

Safety instructions 5

About this Manual 10

Key 10

1 Description 11

1.1 General device description 11

1.2 Device name and product code 12

1.3 Device view 14

1.3.1 Front view 14

1.4 Power supply 16

1.5 Ethernet ports 16

1.5.1 Pin assignments 17

1.6 Display elements 18

1.6.1 Device state 18

1.6.2 Port state 19

2 Configuration interface 20

2.1 USB interface 20

3 Signal contact 21

4 Installation 22

4.1 Checking the package contents 22

4.2 Mounting the device 23

4.2.1 Installing the device onto the DIN rail 23

4.2.2 Mounting on a flat surface 24

4.3 Grounding the device 25

4.4 Installing an SFP transceiver (optional) 26

4.5 Connecting the terminal block 27

4.6 Operating the device 28

4.6.1 Installing terminal blocks, switching on the supply

voltage 28

4.6.2 Connecting data cables 28

4Installation SPIDER-PL

Release

08/2016

5 Configuration (optional) 29

5.1 Configuration readout 33

6 Monitoring the ambient air temperature 34

7 Maintenance and service 35

8Disassembly 36

8.1 Removing an SFP transceiver (optional) 36

8.2 Removing the device 37

9 Technical data 38

A Further Support 51

Installation SPIDER-PL

Release

08/2016 5

Safety instructions

General safety instructions

You operate this device with electricity. Improper usage of the device

entails the risk of physical injury or significant property damage. The

proper and safe operation of this device depends on proper handling

during transportation, proper storage and installation, and careful

operation and maintenance procedures.

Before connecting any cable, read this document, and the safety

instructions and warnings.

Operate the device with undamaged components exclusively.

The device is free of any service components. In case of a damaged

or malfunctioning the device, turn off the supply voltage and return the

device to Hirschmann for inspection.

Certified usage

Use the device solely for the application cases described in the

Hirschmann product information, including this manual.

Operate the device solely according to the technical specifications.

See “Technical data” on page 38.

Installation site requirements

When you are selecting the installation location, make sure you

observe the climatic threshold values specified in the technical data.

Operate the device at the specified ambient temperature (temperature

of the ambient air at a distance of 2 inches (5 cm) from the device) and

at the specified relative humidity exclusively.

Use the device in an environment with a maximum pollution degree

that complies with the specifications in the technical data.

Install the device in a fire enclosure according to EN 60950-1.

Qualification requirements for personnel

Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

Qualified personnel are aware of the dangers that exist in their work.

Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

Qualified personnel receive training on a regular basis.

6Installation SPIDER-PL

Release

08/2016

Device casing

Only technicians authorized by the manufacturer are permitted to open

the housing.

Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not

touch the connection terminals.

Keep the ventilation slits free to ensure good air circulation.

See “General technical data” on page 38.

Install the device in the vertical position.

At ambient temperatures > 140 °F (60 °C):

The surfaces of the device housing may become hot. Avoid touching

the device while it is operating.

Installation SPIDER-PL

Release

08/2016 7

Requirements for connecting electrical wires

Before connecting the electrical wires, always verify that the

requirements listed are complied with.

General requirements for connecting electrical wires

The following requirements apply without restrictions:

The electrical wires are voltage-free.

The cables used are permitted for the temperature range of the application case.

Relevant for North America:

Use 60/75 or 75 °C copper (Cu) wire only.

Requirements for connecting the signal contact

The following requirements apply without restrictions:

The voltage connected complies with the requirements for a safety extra-low voltage

(SELV) as per IEC/EN 60950-1.

The connected voltage is limited by a current limitation device or a fuse.

Observe the electrical threshold values for the signal contact.

See “General technical data” on page 38.

Requirements for connecting the supply voltage

The following requirements apply without restrictions:

All of the following requirements are complied with:

The supply voltage corresponds to the voltage specified on the type plate of the device.

The power supply conforms to overvoltage category I or II.

The power supply has an easily accessible disconnecting device (e.g., a switch or a plug).

This disconnecting device is clearly identified. So in the case of an emergency, it is clear

which disconnecting device belongs to which power supply cable.

The power supply cable is suitable for the voltage, the current and the physical load.

Hirschmann recommends a wire diameter of 0.5 mm² to 0.75 mm² (AWG20 up to AWG18).

The following requirements apply alternatively:

Relevant when the device is supplied via 1 voltage input:

Alternative 1 The power supply complies with the requirements for a limited power source

(LPS) as per EN 60950-1.

Alternative 2 Relevant for North America:

The power supply complies with the requirements as per NEC Class 2

Alternative 3 All of the following requirements are complied with:

The power supply complies with the requirements for a safety extra-low

voltage (SELV) as per IEC/EN 60950-1.

Supply with DC voltage:

A fuse suitable for DC voltage is located in the plus conductor of the power

supply.

The minus conductor is on ground potential. Otherwise, a fuse is also

located in the minus conductor.

Regarding the properties of this fuse:

See “General technical data” on page 38.

Supply with AC voltage:

A fuse is located in the outer conductor of the power supply.

The neutral conductor is on ground potential at both voltage inputs.

Otherwise, a fuse is also located in the neutral conductor.

Regarding the properties of this fuse:

See “General technical data” on page 38.

8Installation SPIDER-PL

Release

08/2016

National and international safety regulations

Verify that the electrical installation meets locally or nationally applicable

safety regulations.

CE marking

The labeled devices comply with the regulations contained in the following

European directive(s):

2011/65/EU (RoHS)

Directive of the European Parliament and of the Council on the restriction

of the use of certain hazardous substances in electrical and electronic

equipment.

2014/30/EU (EMC)

Directive of the European Parliament and the council for standardizing the

regulations of member states with regard to electromagnetic

compatibility.

In accordance with the above-named EU directive(s), the EU conformity

declaration will be at the disposal of the relevant authorities at the

following address:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Tel.: +49 1805 141538

The device can be used in the industrial sector.

Interference immunity: EN 61000-6-2

Emitted interference: EN 55022

Warning! This is a class A device. This device can cause interference in

living areas, and in this case the operator may be required to take

appropriate measures.

Note: The assembly guidelines provided in these instructions must be

strictly adhered to in order to observe the EMC threshold values.

LED or laser components

LED or LASER components according to IEC 60825-1 (2014):

CLASS 1 LASER PRODUCT

CLASS 1 LED PRODUCT

Installation SPIDER-PL

Release

08/2016 9

FCC note:

This device complies with part 15 of the FCC rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference; (2) this device must accept any interference received,

including interference that may cause undesired operation.

Appropriate testing has established that this device fulfills the

requirements of a class A digital device in line with part 15 of the FCC

regulations.

These requirements are designed to provide sufficient protection against

interference when the device is being used in a business environment.

The device creates and uses high frequencies and can also radiate these

frequencies. If it is not installed and used in accordance with this

operating manual, it can cause radio transmission interference. The use

of this device in a residential area can also cause interference, and in this

case the user is obliged to cover the costs of removing the interference.

Recycling note

After usage, this device must be disposed of properly as electronic waste,

in accordance with the current disposal regulations of your county, state,

and country.

10 Installation SPIDER-PL

Release

08/2016

About this Manual

The “Installation” user manual contains a device description, safety

instructions, a description of the display, and the other information that you

need to install the device.

Key

The symbols used in this manual have the following meanings:

Listing

Work step

Subheading

Inhaltsverzeichnis

Andere Hirschmann Netzwerk-Router Handbücher

Hirschmann

Hirschmann RSR20-0900 Bedienungsanleitung

Hirschmann

Hirschmann OCTOPUS 5TX-EEC Handbuch

Hirschmann

Hirschmann RS20 series Betriebsanleitung

Hirschmann

Hirschmann RS20 series Bedienungsanleitung

Hirschmann

Hirschmann PowerMICE Bedienungsanleitung

Hirschmann

Hirschmann RS40 series Bedienungsanleitung

Hirschmann

Hirschmann RSB20-0800T1T1 Bedienungsanleitung

Hirschmann

Hirschmann MS30, Power MICE, MACH 4000, OCTOPUS Bedienungsanleitung

Hirschmann

Hirschmann HiSecOS EAGLE20 Bedienungsanleitung

Hirschmann

Hirschmann MM2-2FXM3/2TX1 Handbuch

Hirschmann

Hirschmann MACH 4000 Series Bedienungsanleitung

Hirschmann

Hirschmann MICE MS20-1600 Series Bedienungsanleitung

Hirschmann

Hirschmann SPIDER 3TX-TAP Handbuch

Hirschmann

Hirschmann MICE MS20 Bedienungsanleitung

Hirschmann

Hirschmann SPIDER-SL-40-08T1 Bedienungsanleitung

Hirschmann

Hirschmann MACH 1020 Bedienungsanleitung

Hirschmann

Hirschmann HiSecOS EAGLE20 Bedienungsanleitung

Hirschmann

Hirschmann RS30-...U Series Bedienungsanleitung

Hirschmann

Hirschmann OWL LTE M12 Bedienungsanleitung

Hirschmann

Hirschmann OWL 4G Europe Bedienungsanleitung

Hirschmann

Hirschmann MACH104-20TX-F Series Bedienungsanleitung

Hirschmann

Hirschmann GigaLION-24TP Bedienungsanleitung

Hirschmann

Hirschmann OWL-IPG-AMERICAS Bedienungsanleitung

Hirschmann

Hirschmann OWL LTE M12 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise