Hirschmann RSPE30 Bedienungsanleitung

Installation RSPE30/32/35/37

Release

04/2019

Technical support

https://hirschmann-support.belden.com

User Manual

Installation

Industrial Ethernet Rail Switch Power

RSPE30/32/35/37

26.04.2019 Installation RSPE30/32/35/37

Release

04/2019

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Installation RSPE30/32/35/37

Release

04/2019 3

Contents

Safety instructions 6

About this manual 18

Key 19

1 Description 20

1.1 General description 20

1.2 Device name and product code 21

1.3 Device views 25

1.3.1 Front view 25

1.3.2 Rear view 26

1.4 Power supply 27

1.4.1 Supply voltage with the characteristic value K9 27

1.4.2 Supply voltage with the characteristic value KK 27

1.4.3 Supply voltage with the characteristic value CC 27

1.4.4 Supply voltage with the characteristic value PP 27

1.5 Ethernet ports 28

1.5.1 10/100 Mbit/s twisted pair port 29

1.5.2 Gigabit combo port 29

1.5.3 100 Mbit/s F/O port (optional) 30

1.5.4 Support of PoE(+) 31

1.6 Display elements 32

1.6.1 Device state 32

1.6.2 Media module status 33

1.6.3 Port status 34

1.7 Management interfaces 36

1.7.1 V.24 interface (external management) 36

1.7.2 SD card interface 36

1.7.3 USB interface 37

1.8 Signal contact 37

2 Installation 38

2.1 Checking the package contents 38

2.2 Installing the SD card (optional) 38

4Installation RSPE30/32/35/37

Release

04/2019

2.3 Mounting a cover panel or a media module 39

2.3.1 Mounting a cover panel 39

2.3.2 Mounting a media module 39

2.4 Installing and grounding the device 39

2.4.1 Installing the device onto the DIN rail 40

2.4.2 Grounding the device 41

2.5 Installing an SFP transceiver (optional) 41

2.6 Connecting the terminal blocks 42

2.6.1 Supply voltage with the characteristic value K9 42

2.6.2 Supply voltage with the characteristic value KK 43

2.6.3 Supply voltage with the characteristic value CC 45

2.6.4 Supply voltage with the characteristic value PP 46

2.6.5 Signal contact 47

2.7 Operating the device 48

2.8 Connecting data cables 48

2.9 Filling out the inscription label 49

3 Making basic settings 50

4 Monitoring the ambient air temperature 51

5 Maintenance and service 52

6Disassembly 53

6.1 Removing the device 53

6.2 Removing an SFP transceiver (optional) 54

6.3 Removing a media module (optional) 54

7 Technical data 55

7.1 General technical data 55

7.2 Dimension drawings 59

7.3 EMC and immunity 61

7.4 Network range 64

7.5 Power consumption/power output 68

7.6 Scope of delivery, order numbers and accessories 68

Installation RSPE30/32/35/37

Release

04/2019 5

8 Underlying technical standards 71

A Further support 72

6Installation RSPE30/32/35/37

Release

04/2019

Safety instructions

General safety instructions

You operate this device with electricity. Improper usage of the device

entails the risk of physical injury or significant property damage. The

proper and safe operation of this device depends on proper handling

during transportation, proper storage and installation, and careful

operation and maintenance procedures.

Before connecting any cable, read this document, and the safety

instructions and warnings.

Operate the device with undamaged components exclusively.

The device is free of any service components. In case of a damaged

or malfunctioning device, turn off the supply voltage and return the

device to Hirschmann for inspection.

Certified usage

Use the product only for the application cases described in the

Hirschmann product information, including this manual.

Operate the product only according to the technical specifications.

See “Technical data” on page 55.

Connect to the product only components suitable for the requirements

of the specific application case.

Installation site requirements

Install the device in a fire enclosure according to EN 60950-1.

Only for device variants featuring supply voltage with characteristic

value K9 or KK:

Install this device solely in a switch cabinet or in an operating site with

restricted access, to which maintenance staff have exclusive access.

Install the device at ambient temperatures greater than +113 °F

(+45 °C) in “restricted access locations” based on EN 60950-1

exclusively.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

Installation RSPE30/32/35/37

Release

04/2019 7

Device casing

Only technicians authorized by the manufacturer are permitted to open

the casing.

Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not

touch the connection terminals.

Keep the ventilation slits free to ensure good air circulation.

Mount the device in the vertical position.

At ambient air temperatures > 140 °F (+60 °C):

The surfaces of the device housing may become hot. Avoid touching

the device while it is operating.

Qualification requirements for personnel

Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

Qualified personnel are aware of the dangers that exist in their work.

Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

Qualified personnel receive training on a regular basis.

National and international safety regulations

Verify that the electrical installation meets local or nationally applicable

safety regulations.

Grounding the device

Grounding the device is by means of a separate ground connection on the

device.

Ground the device before connecting any other cables.

Disconnect the grounding only after disconnecting all other cables.

Always ground the device via the grounding screw.

Shielding ground

The overall shield of a connected shielded twisted pair cable is connected

to the grounding connector on the front panel as a conductor.

Beware of possible short circuits when connecting a cable section with

conductive shielding braiding.

Requirements for connecting electrical wires

Before connecting the electrical wires, always verify that the

requirements listed are complied with.

8Installation RSPE30/32/35/37

Release

04/2019

Requirements for connecting the signal contact

Requirements for connecting the supply voltage

All of the following requirements are complied with:

The electrical wires are voltage-free.

The cables used are permitted for the temperature range of the application case.

Table 1: Requirements for connecting electrical wires

All of the following requirements are complied with:

The voltage connected complies with the requirements for a safety extra-low voltage

(SELV) as per IEC/EN 60950-1.

The connected voltage is limited by a current limitation device or a fuse.

Observe the electrical threshold values for the signal contact.

See “General technical data” on page 55.

Table 2: Requirements for connecting the signal contact

Device variant Requirements

All variants All of the following requirements are complied with:

The supply voltage corresponds to the voltage specified on the type

plate of the device.

The power supply conforms to overvoltage category I or II.

The power supply has an easily accessible disconnecting device (for

example a switch or a plug). This disconnecting device is clearly

identified. So in the case of an emergency, it is clear which

disconnecting device belongs to which power supply cable.

The cross-section of the ground conductor is the same size as or

bigger than the cross-section of the power supply cables.

Relevant for North America:

The power supply cables are suitable for ambient air temperatures of

at least 167 °F (75 °C). The power supply cable wires are made of

copper.

Table 3: Requirements for connecting the supply voltage

Installation RSPE30/32/35/37

Release

04/2019 9

Only for device

variants featuring

supply voltage with

the characteristic

value CC:

If you connect 2 independent power sources, verify that the minus

terminal is grounded. Failure to follow this instruction can result in

equipment damage.

The wire diameter of the power supply cable is at least 1 mm² (North

America: AWG16) on the supply voltage input.

The following requirements are alternatively complied with:

Alternative 1 The power supply complies with the requirements

for a limited power source (LPS) as per EN 60950-1.

Alternative 2 Relevant for North America:

The power supply complies with the requirements

according to NEC Class 2.

Alternative 3 All of the following requirements are complied with:

The power supply complies with the

requirements for a safety extra-low voltage

(SELV) as per IEC/EN 60950-1.

A fuse suitable for DC voltage is located in the

plus conductor of the power supply.

The minus conductor is on ground potential.

Otherwise, a fuse is also located in the minus

conductor.

Regarding the properties of this fuse:

See “General technical data” on page 55.

Device variant Requirements

Table 3: Requirements for connecting the supply voltage

10 Installation RSPE30/32/35/37

Release

04/2019

Supply voltage

The supply voltage is connected to the device casing through protective

elements exclusively.

For supply voltage connections with protective conductor connection:

First connect the protective conductor before connecting the wires for

the supply voltage.

Exclusively for

device variants

featuring supply

voltage with

characteristic

value PP:

If you connect 2 independent power sources, verify that the plus terminal

of the power sources is not connected to each other. Failure to follow

these instructions can result in equipment damage.

The wire diameter of the power supply cable is at least 1 mm² (North

America: AWG16) on the supply voltage input.

The following requirements are alternatively complied with:

Alternative 1 The power supply complies with the requirements

for a limited power source (LPS) as per EN 60950-1.

Alternative 2 All of the following requirements are complied with:

The power supply complies with the

requirements for a safety extra-low voltage

(SELV) as per IEC/EN 60950-1.

A fuse suitable for DC voltage is located in the

plus conductor of the power supply.

The minus conductor is on ground potential.

Otherwise, a fuse is also located in the minus

conductor.

Regarding the properties of this fuse:

See “General technical data” on page 55.

Only for device

variants featuring

supply voltage with

characteristic

value K9 or KK:

All of the following requirements are complied with:

Supply with DC voltage:

A fuse suitable for DC voltage is located in the plus conductor of the

power supply.

The minus conductor is on ground potential. Otherwise, a fuse is also

located in the minus conductor.

Regarding the properties of this fuse:

See “General technical data” on page 55.

The wire diameter of the power supply cable is at least 1 mm² (North

America: AWG16) on the supply voltage input.

Supply with AC voltage:

A fuse is located in the outer conductor of the power supply.

The neutral conductor is on ground potential at both voltage inputs.

Otherwise, a fuse is also located in the neutral conductor.

Regarding the properties of this fuse:

See “General technical data” on page 55.

The wire diameter of the power supply cable is at least 0.75 mm²

(North America: AWG18) on the supply voltage input.

Device variant Requirements

Table 3: Requirements for connecting the supply voltage

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hirschmann Schalten Handbücher

Hirschmann

Hirschmann PowerMICE MS4128 Bedienungsanleitung

Hirschmann

Hirschmann OS20-001000T5T5TAFUHB Bedienungsanleitung

Hirschmann

Hirschmann 943 686-003 Bedienungsanleitung

Hirschmann

Hirschmann Dragon PTN Bedienungsanleitung

Hirschmann

Hirschmann RS20 series Bedienungsanleitung

Hirschmann

Hirschmann MSM20 Bedienungsanleitung

Hirschmann

Hirschmann MACH104-20TX-F Series Bedienungsanleitung

Hirschmann

Hirschmann BATOne Bedienungsanleitung

Hirschmann

Hirschmann RSP 20 Bedienungsanleitung

Hirschmann

Hirschmann MSM20 Bedienungsanleitung

Hirschmann

Hirschmann RS20 series Bedienungsanleitung

Hirschmann

Hirschmann RSPL 20 Bedienungsanleitung

Hirschmann

Hirschmann MACH1000 Series Bedienungsanleitung

Hirschmann

Hirschmann MACH 4000 Series Bedienungsanleitung

Hirschmann

Hirschmann MACH102 Series Bedienungsanleitung

Hirschmann

Hirschmann LRS Series Bedienungsanleitung

Hirschmann

Hirschmann LION-GIGA-1SX Bedienungsanleitung

Hirschmann

Hirschmann ETHERNET IP67 Bedienungs- und Montageanleitung

Hirschmann

Hirschmann CS30 Bedienungsanleitung

Hirschmann

Hirschmann GREYHOUND GMM42 Bedienungsanleitung

Hirschmann

Hirschmann OCTOPUS 8TX-EEC Bedienungsanleitung

Hirschmann

Hirschmann RS20 series Bedienungsanleitung

Hirschmann

Hirschmann RS2-5TX/FX Handbuch

Hirschmann

Hirschmann MSP30 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung