Hitachi X200 Series Bedienungsanleitung

X200 Series Inverter

Quick Reference Guide

•Single-phase Input 200V class

•Three-phase Input 200V class

•Three-phase Input 400V class

Hitachi Industrial Equipment Systems Co., Ltd.

Manual No. NT3011XB •Sep 2007

- 1 -

Caution: Be sure to read the X200 Manual and the X200 Manual

Addendum, and follow their Cautions and Warnings for the initial

product installation. This Quick Reference Guide is intended for

reference use by experienced users in servicing existing installations.

Power Circuit Terminals

Inverter models X200-002SFEF/NFU, -004SFEF/NFU

Inverter models X200-005SFEF, -007SFEF/NFU to -022SFEF/NFU,

-037LFU to -075LFU, 004HFEF/HFU to –075HFEF/HFU

Caution: Power terminal assignment is is different compared to old

models such as L100, L200 series. Pay attention when wiring the

power cable.

Jumper

U/T1

V/T2

W/T3

- +

/ N

Jumper

SFEF

L3/N

Jumper

NFU

/ N

U/T1

V/T2

W/T3

- +

Jumper

L3/N

Jumper

R/L1

S/L2

T/L3

Jumper

SFEF

NFU,LFU

HFEF,HFU

- 2 -

Control Circuit Terminals

Terminal Name Description Ratings and Notes

P24 +24V for logic inputs 24VDC supply, 30mA max.

(Notes: Do not use for network

power. Do not short to terminal

1, 2, 3, 4, 5 Intelligent (programmable

discrete logic) inputs 27VDC max. (Use P24 or an

external supply reference to

terminal L), 4.7kΩinput

impedance.

11 Discrete logic output 50mA max. ON current, 27VDC

max. OFF voltage

L (right) GND for logic inputs Sum of input 1 to 5 currents

(Note: Do not ground)

CM2 Common for logic

outputs 50mA max for terminal 11

current

AM Analog voltage output 0 to 10VDC, 1mA max.

L (left) Common for analog

inputs Sum of OI, O and H currents

(return)

OI Analog input, current 4 to 19.6mArange, 20mA nom.

O Analog input, voltage 0 to 9.6VDC range, 10VDC

nominal, 12VDC max., input

impedance 10kΩ

H +10V analog reference 10VDC nominal, 10mAmax.

AL0 Relay common contact

AL1 Relay contact, normally

closed during RUN

AL2 Relay contact, normally

open during RUN

Contact rating

Max resistive load=250VAC,

2.5A; 30VDC 3A;

Max inductive load=250VAC,

0.2A; 30VDC 0.7A

Minimum load=5VDC 100mA,

100VAC 10mA

Note) Analog input O and OI cannot be used at the same time.

AM H O OI

PCS

P24

CM2

Jumper

nalog

output

nalog

inputs Logic inputs Logic

outputs

AL2 AL1 AL0

Alarm relay

- 3 -

Basic Wiring Diagram

The following wiring diagram shows the power and motor connections

for basic operation. The optional signal input wiring supports external

Fwd and Rev Run command, and a speed potentiometer.

X200 series

(L1)

(N/L3)

(T1)

(T3)

(T2) Motor

From 3-phase or

single-phase power input

source

(See specifications label

on inverter for details)

P24

Wiring for Source type models

(L2)

Inputs:

Analog reference

External speed

reference POT.

Analog common

AL1

AL0

AL2

Alarm contacts, 1C

CM2

Open collector output

Frequency

arrival signal

Load

Logic output

common

PCS

Forward

Reverse

Short bar

Reset

- 4 -

Inverter Keypad Operation

•Run/Stop LED – ON when the inverter output is ON and the motor

is developing torque (Run Mode), and OFF when the inverter output

is OFF (Stop Mode).

•Program/Monitor LED – This LED is ON when the inverter is ready

for parameter editing (Program Mode). It is OFF when the

parameter display is monitoring data (Monitor Mode).

•Run Key Enable LED – is ON when the inverter is ready to respond

to the Run key, OFF when the Run key is disabled.

•Run Key – Press this key to run the motor (the Run Enable LED

must be ON first). Parameter F004, Keypad Run Key Routing,

determines whether the Run key generates a Run FWD or Run REV

command.

•Stop/Reset Key – Press this key to stop the motor when it is running

(uses the programmed deceleration rate). This key will also reset an

alarm that has tripped.

•Potentiometer – Allows an operator to directly set the motor speed

when the potentiometer is enabled for output frequency control.

•Potentiometer Enable LED – ON when the potentiometer is enabled

for value entry.

•Parameter Display – A 4-digit, 7-segment display for parameters

and function codes.

•Display Units, Hertz/Amperes – One of these LEDs will be ON to

indicate the units associated with the parameter display.

•Power LED – This is ON when the power input to the inverter is

ON.

•Alarm LED – ON when an inverter trip is active (alarm relay

contact will be closed).

•Function Key – This key is used to navigate through the lists of

parameters and functions for setting and monitoring parameter

values.

•Up/Down keys – Use these keys alternatively to move up or down

the lists of parameter and functions shown in the display, and

increment/decrement values.

•Store key – When the unit is in Program Mode and you have edited

a parameter value, press the Store key to write the new value to the

EEPROM.

Display Units (Hertz / Amperes) LEDs

Parameter Display

Run key Enable LED

Run key

Stop/Reset key

PRG

RUN

POWER

ALARM

STOP

RESET

Function key Up/Down keys Store key

Power LED

Alarm LED

Run/Stop LED

Program/Monitor LED

Potentiometer Enable LED

Potentiometer

FUNC STR

- 5 -

Keypad Navigation Map

STR

Monitor Mode

PRG LED=OFF Program Mode

PRG LED=ON

Display Data

FUNC

Select

Function or

Grou

Power down

FUNC FUNC

Store as

powerup

default

Increment/

decrement

value

Edit

FUNC

Write

data to

EEPROM

Return to

parameter

list

Select parameter Edit parameter

- 6 -

Powerup Test

The Powerup Test procedure uses minimal parameter settings to run

the motor. The procedure describes two alternative methods for

commanding the inverter:

via the inverter keypad, or via the logic

terminals.

yCheck power input and motor output wiring (see page 3 diagram).

yIf using logic terminals for testing, verify correct wiring on [PCS],

[FW], [H], [O] and [L] (bottom row) per the diagram on page 3.

yReverse [RV] input wiring (defaults to terminal [2]) is optional.

Step

Description Via Keypad Via Logic

Terminals

1 Set speed command

source setting

A001=00

(Keypad pot)

A001=01

[H-O-L] input

2 Set Run FW command

source

A002=02

(Run key)

A002=01

[FW] input

3 Set Run REV

command source −C002=01 (default)

[RV] input

4 Set motor base freq. A003=60

5 Set motor poles H004 = 4 (default), change only if your motor is

different

Set keypad display to

monitor freq. Access d001, press Func key, display will show 0.0

Disconnect load from motor

7 Perform safety check Turn keypad pot. To MIN

position

Ensure voltage on [O] −

[L] terminals = 0V

8 Run Forward

command Press Run key Turn ON the [FW]

terminal

9 Increase speed Rotate keypad pot. CW

direction Increase voltage at [O]

10 Decrease speed Rotate keypad pot. CCW

direction Decrease voltage at [O]

11 Stop motor Press stop key Turn OFF the [FW]

terminal

12 Run Reverse

command (optional) −Turn ON the [RV]

terminal

13 Stop motor −Turn OFF the [RV]

terminal

- 7 -

Error Codes

The X200 series inverters will trip on over-current, over-voltage, and

under-voltage to protect the inverter. The motor output turns OFF,

allowing the motor to free-run to a stop. Press the Stop/Reset key to

reset the inverter and clear the error.

Basic Error Codes

Error

Code Name Probable Cause(s)

E_01 Over current event

while at constant speed

E_02 Over current event

during deceleration

E_03 Over current event

during acceleration

yInverter output was short-circuited

yMotor shaft is locked

yLoad is too heavy

yA dual voltage motor is wired

incorrectly

Note: The X200 will over-current trip at

nominally 200% of the rated current.

E_04 Over current event for

other conditions

yDC braking power (A_54) set too high

yCurrent transformer / noise error

E_05 Overload protection yMotor overload is detected by the

electronic thermal function

E_07 Over voltage protection

yDC bus voltage exceeds a threshold,

due to regeneration energy from the

motor

E_08 EEPROM error

yBuilt-in EEPROM memory

experienced noise, high temperature,

etc.

E_09 Under voltage error

yDC bus voltage decreased enough to

cause a control circuit fault

yInstantaneous power failure occurred

E_11 CPU error yBuilt-in CPU had internal error

E_12 External trip y[EXT] input signal detected

E_13 USP (Unattended Start

Protection)

yWhen (USP) was enabled, an error

occurred when power was applied while

a Run signal was present

E_14 Ground fault

yA ground fault was detected between

the inverter output and the motor. This

feature protects the inverter, and does

not protect humans.

E_15 Input over-voltage yInput voltage was higher than the

specified value, 100 sec. after powerup

E_21 Inverter thermal trip yInverter internal temperature is

above the threshold

E_30 Driver error Refer to E_01~E_04

E_35 Thermistor yThermistor input, [5] and [L] is over

the temperature threshold

E_37 Emergency stop yEmergency stop signal has given

E_60 Communications error yCommunication error on RS485

MODBUS communication

- - -

Under-voltage

(brownout) with output

shutoff

yLow input voltage caused the inverter

to turn OFF the motor output and try to

restart. If unsuccessful, a trip occurs.

- 8 -

Error Trip Conditions

Use function code d081 to access the error trip conditions for the current

error as shown in the table below. Use the Up and Down arrow keys to

scroll through the trip condition parameters.

Step Display

1. Access d081 d081

If no error:

_ _ _

2. Press Function Key

If error exists:

E_xx

(error code)

3. Press Up/Dn key

(if error exists)

Output frequency at trip point:

48.50

Motor current at trip point:

10.3

DC bus voltage at trip point:

189.5

Cumulative Run hours at trip point:

Cumulative power-ON hours at trip point:

- 9 -

Restoring Factory Default Settings

Action Display Function/Parameter

Press , or as

needed b- - - “B” Group selected

Press b001 First “B” Group parameter

Press/hold until… b085 Country code for

initialization selected

Press . If setting is

correct, then skip next step. 02

00 = Japan

01 = Europe

02 = United States

To change country code, press or to set; to store.

Press b085 Country code for

initialization selected

Press b084 Initialization function

selected

Press 00 00 = disable initialization

Press 01 01 = enable initialization

Press b084 Initialization now enable to

restore all defaults

Press/hold , and

keys. Do not release yet. b084 First part of key sequence

When your country code

appears in the display, release

all the keys.

USA

Default parameter country

code shown during

initialization

Initialization is complete. d001 Function code for output

frequency monitor shown

Note: After initializing the inverter, use the Powerup Test on

page 6 to get the motor running again.

FUNC

STR

FUNC

STR

FUNC

STOP

RESET

Andere Handbücher für X200 Series

Inhaltsverzeichnis

Andere Hitachi Wechselrichter Handbücher

Hitachi

Hitachi RAS-80YHA4 Leitfaden

Hitachi

Hitachi CP-X200 CP-X300 Bedienungsanleitung

Hitachi

Hitachi J300 Series Bedienungsanleitung

Hitachi

Hitachi sj300CE series Bedienungsanleitung

Hitachi

Hitachi IVX-ES Series Bedienungsanleitung

Hitachi

Hitachi AN032404-1 Rev. A Montage- und Bedienungsanleitung

Hitachi

Hitachi L300P Series Bedienungsanleitung

Hitachi

Hitachi SJ100DN DeviceNet Series Addendum Bedienungsanleitung

Hitachi

Hitachi L200 Series Bedienungsanleitung

Hitachi

Hitachi L100 Series Bedienungsanleitung

Hitachi

Hitachi HFC-VWS3 U SERIES, HFC-VWS3 H SERIES Bedienungsanleitung

Hitachi

Hitachi WJ200-007MF Bedienungsanleitung

Hitachi

Hitachi J300 Series Bedienungsanleitung

Hitachi

Hitachi SJ700-2 Series Bedienungsanleitung

Hitachi

Hitachi SJ100 Series Bedienungsanleitung

Hitachi

Hitachi WJ200 Series Software Bedienungsanleitung

Hitachi

Hitachi E43 Bedienungsanleitung

Hitachi

Hitachi SJ Series Bedienungsanleitung

Hitachi

Hitachi NT2021XA Bedienungsanleitung

Hitachi

Hitachi L200 Series Bedienungsanleitung

Hitachi

Hitachi SJ2-CO Bedienungsanleitung

Hitachi

Hitachi SJ700-2 Series Bedienungsanleitung

Hitachi

Hitachi SJ100 Series Bedienungsanleitung

Hitachi

Hitachi L100 300 Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

Astrel Group

Astrel Group Power Reducer Kurzanleitung

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung