Hitachi CP-WU8700 Bedienungsanleitung

ENGLISH

Projector

CP-WU8700/CP-WX8750/CP-X8800

CP-WU8600/CP-WX8650

User's Manual (concise)

Thank you for purchasing this projector.

Please read through this manual before using this product, in order to use safely

and utilize well the product.

WARNING ►Before using this product, be sure to read all manuals for this

product. After reading them, store them in a safe place for future reference.

►Heed all the warnings and cautions in the manuals or on the product.

►Follow all the instructions in the manuals or on the product.



First of all............................................ 2

Entries and graphical symbols explanation ......2

Important safety instruction ..............................2

Regulatory notices.............................. 3

About Electro-Magnetic Interference ................3

About Waste Electrical and Electronic Equipment

...4

Contents of package........................... 4

Installing the lens unit......................... 5

Preparing for the remote control......... 5

Arrangement....................................... 6

Connecting with your devices............. 9

Fastening the adapter cover............. 10

Attaching the terminal cover............. 11



Connecting power supply ................. 12

Turning on the power........................ 13

Adjusting the projector's elevator ..... 14

Adjusting the lens position................ 14

Displaying the picture ....................... 15

Turning off the power........................ 16

Replacing the lamp........................... 17

Cleaning and replacing the air lter

.. 19

Replacing the internal clock battery

Using the CD manual ....................... 22

Specications ................................... 23

Troubleshooting

- Warranty and after-service ........... 25

Contents

NOTE •

In this manual, unless any comments are accompanied, “the manuals”

means all the documents provided with this product, and “the product” means this

projector and all the accessories came with the projector.

First of all

Entries and graphical symbols explanation

The following entries and graphical symbols are used for the manuals and the product

as follows, for safety purpose. Please know their meanings beforehand, and heed them.

Important safety instruction

The followings are important instructions for safely using the product. Be sure to

follow them always when handling the product. The manufacturer assumes no

responsibility for any damage caused by mishandling that is beyond normal usage

dened in these manuals of this projector.

WARNING

This entry warns of a risk of serious personal injury or even death.

CAUTION This entry warns of a risk of personal injury or physical damage.

NOTICE This entry notices of fear of causing trouble.

WARNING ►Never use the product in or after an abnormality (ex. giving

off smoke, smelling strange, took a liquid or an object inside, broken, etc.) If an

abnormality should occur, unplug the projector urgently.

►Situate the product away from children and pets.

►Keep small parts away from children and pets. If swallowed, consult a

physician immediately for emergency treatment.

►Do not use the product when there is fear of a thunderbolt.

►Unplug the projector from the power outlet if the projector is not used for the

time being.

►

Do not connect the projector to a power supply while no lens unit is attached to it.

►Do not open or remove any portion of the product, unless the manuals direct

it. For internal maintenance, leave it to your dealer or their service personnel.

►Use only the accessories specied or recommended by the manufacturer.

►Do not modify the projector or accessories.

►Do not let any things or any liquids enter to the inside of the product.

►Do not wet the product.

►

Do not place the projector where any oils, such as cooking or machine oil, are used.

Oil may harm the product, resulting in malfunction, or falling from the mounted position.

►Do not apply a shock or pressure to this product.

- Do not place the product on an unstable place such as the uneven surface

or the leaned table.

- Do not place the product unstably. Place the projector so that it does not

protrude from the surface where the projector is placed on.

- Place your hands on the grip on the bottom of the projector when carrying

the projector.

- Remove all the attachments including the power cord and cables, from the

projector when carrying the projector.

►

Do not look into the lens and the openings on the projector, while the lamp is on,

since the projection ray may cause a trouble on your eyes.

►

Do not approach the lamp cover and the exhaust vents, while the projection lamp

is on. Also after the lamp goes out, do not approach them for a while, since too hot.

ENGLISH

Regulatory notices

About Electro-Magnetic Interference

This is a Class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

This product may cause interference if used in residential areas. Such use must

be avoided unless the user takes special measures to reduce electromagnetic

emissions to prevent interference to the reception of radio and television

broadcasts.

In Canada

CAN ICES-3(A) / NMB-3(A).

In the US and places where the FCC regulations are applicable

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential

area is likely to case harmful interference in which case the user will be required to

correct the interference at his own expense.

INSTRUCTIONS TO USERS: Some cables have to be used with the core set.

Use the accessory cable or a designated type cable for the connection. For cables

that have a core only at one end, connect the core to the projector.

CAUTION: Changes or modications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

Contents of package

Your projector should come with the items

shown below. Check that all the items are

included. Require of your dealer immediately

if any items are missing.

(1) Remote control with the two AA batteries

(2) Power cord

(3) Computer cable

(4) Lens hole cover

(5) User’s manuals (Book x1, CD x1)

(6) Security label

(7) Application CD

(8) Adapter cover

(9) Terminal cover

(10) HDMI cable holder (x2)

(11) Cable tie (x2)

NOTE • Keep the original packing materials for future reshipment. Be sure to

use the original packing materials when moving the projector. Remove the lens

unit and attach the lens hole cover when moving the projector.

About Waste Electrical and Electronic Equipment

The mark is in compliance with the Waste Electrical and Electronic

Equipment Directive 2002/96/EC (WEEE).

The mark indicates the requirement NOT to dispose the equipment

including any spent or discarded batteries or accumulators as unsorted

municipal waste, but use the return and collection systems available.

If the batteries or accumulators included with this equipment, display

the chemical symbol Hg, Cd, or Pb, then it means that the battery has a

heavy metal content of more than 0.0005% Mercury or more than, 0.002%

Cadmium, or more than 0.004% Lead.

Regulatory notices (continued)

(5)

(6)

(2)

(3)

(4)

(1)

(7)

(8)

(9)

(10)

(11)

WARNING ►Keep small parts away from children and pets. Take care

not to put in the mouth. If swallowed, consult a physician immediately for

emergency treatment.

ENGLISH

Preparing for the remote control

Please insert the batteries into the remote control before using it. If the remote

control starts to malfunction, try to replace the batteries. If you will not use the

remote control for long period, remove the batteries from the remote control and

store them in a safe place.

1. Holding the hook part of the battery

cover, remove it.

2. Align and insert the two AA batteries

according to their plus and minus

terminals as indicated in the remote

control. (Use the appropriate AA

carbon-zinc or alkaline batteries (non-

rechargeable) in accordance with laws

and regulations.)

3. Replace the battery cover in the direction of the arrow

and snap it back into place.

WARNING ►Always handle the batteries with care and use them only as

directed. Improper use may result in battery explosion, cracking or leakage,

which could result in re, injury and/or pollution of the surrounding environment.

• When replacing the batteries, replace both of the batteries with new batteries

of the same type. Do not use a new battery with a used battery.

• Be sure to use only the batteries specied. Do not use batteries of different

types at the same time. Do not mix a new battery with used one.

•

Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

•

Do not place a battery in a re or water. Keep batteries in a dark, cool and dry place.

•

If you observe battery leakage, wipe out the leakage and then replace a battery.

If the leakage adheres to your body or clothes, rinse well with water immediately.

• Obey the local laws on disposing the battery.

1 3

Installing the lens unit

See the manual of the optional lens.

Arrangement

Refer to tables T-1 to T-3 at the back of this manual as well as the following to

determine the screen size and projection distance. The values shown in the table

are calculated for a full size screen.

Projector top

Projector bottom

Ⓗ×Ⓥ : Screen size

ⓐ:

Projection distance

(from the front of the

projector unit)

Secure a clearance of 50cm or greater between the exhaust vents and walls, and

a clearance of 30cm or greater between the intake vents and walls. Assume that

there is enough clearance in the front, back, and top of the projector in the  gure

below.

Secure a clearance of 50cm or greater between the exhaust vents and walls.

Assume that there is enough clearance in the front, sides, and top of the projector

in the  gure below.

(continued on next page)

50cm or greater

Intake

vents

Exhaust

vents

30cm or greater

50cm or greater

Exhaust

vents

ENGLISH

Secure a clearance of 50cm or greater when installing the projectors side by

side. As for the required clearance not shown in the gure below, follow the

installation mentioned above.

Secure a clearance of 30cm or greater between the intake vents and walls

when installing the projector in portrait mode. As for the required clearance not

shown in the gure below, follow the installation mentioned above.

(continued on next page)

Arrangement (continued)

50cm or greater

30cm or greater

Intake

vents

WARNING ►Install the projector where you can access the power outlet

easily.

►Install the projector in a stable horizontal position.

• Do not use any mounting accessories except the accessories specied by the

manufacturer. Read and keep the manuals of the accessories used.

• For special installation such as ceiling mounting, be sure to consult your

dealer beforehand. Specic mounting accessories and services may be

required.

• Do not put the projector on its side, front or rear position.

• Do not attach nor place anything on the projector unless otherwise specied

in the manual.

►Do not install the projector near thermally conductive or ammable things.

►Do not place the projector where any oils, such as cooking or machine oil, are

used.

►Do not place the projector in a place where it may get wet.

►Do not block the intake vents and exhaust vents of the projector. If the intake

vents and exhaust vents of the projector are blocked, the accumulated inside

heat may cause re.

CAUTION ►Place the projector in a cool place with sufcient ventilation.

• Do not stop up, block nor cover the projector's vent holes.

• Do not place the projector at places that are exposed to magnetic elds, doing

so can cause the cooling fans inside the projector to malfunction.

►Avoid placing the projector in smoky, humid or dusty place.

• Do not place the projector near humidiers.

NOTICE ►Position the projector to prevent light from directly hitting the

projector’s remote sensor.

►Do not place the product in a place where radio interference may be caused.

►Set the ALTITUDE MODE of the SERVICE item in the OPTION menu cor-

rectly. It is recommended to leave it at AUTO usually. If the projector is used

with a wrong setting, it may cause damage to the projector itself or the parts

inside. For details, see User’s Manual - Operating Guide.

• When the temperature inside the projector rises high, it may cause the

high rotation of the fan for cooling temporarily.

NOTE

Arrangement (continued)

ENGLISH

Connecting with your devices

Before connecting the projector to a device, consult the manual of the device to

conrm that the device is suitable for connecting with this projector and prepare

the required accessories, such as a cable in accord with the signal of the device.

Consult your dealer when the required accessory did not come with the product or

the accessory is damaged.

After making sure that the projector and the devices are turned off, perform the

connection, according to the following instructions. Refer to gures F-1 to F-9 at the

back of this manual.

For details, see User’s Manual - Operating Guide. Before connecting the projector

to a network system, be sure to read User’s Manual - Network Guide too.

WARNING ►Use only the appropriate accessories. Otherwise it could

cause a re or damage the projector and devices.

• Use only the accessories specied or recommended by the projector’s

manufacturer. It may be regulated under some standard.

• Neither disassemble nor modify the projector and the accessories.

• Do not use the damaged accessory. Be careful not to damage the accesso-

ries. Route a cable so that it is neither stepped on nor pinched out.

►

Heat may build up in the USB wireless adapter, to avoid possible burns dis-

connect the projector power cord for 10 minutes before touching the adapter.

• When using the USB wireless adapter, use the supplied adapter cover or

terminal cover (10,11).

CAUTION ►For a cable with a core at only one end, connect the end with

the core to the projector. That may be required by EMI regulations.

►Before connecting the projector to a network system be sure to obtain the

consent of the administrator of the network.

►

Do not connect the LAN port to any network that might have the excessive

voltage.

►

The designated USB wireless adapter that is sold as an option is required to

use the wireless network function of this projector. Before connecting the USB

wireless adapter, turn off the power of the projector and disconnect the power

cord.

NOTE • Do not turn on or off the projector while connected to a device in

operation, unless that is directed in the manual of the device.

• Some input ports are selectable in the use. For details, see User's Manual -

Operating Guide.

• Be careful not to mistakenly connect a connector to a wrong port.

When using the USB wireless adapter, use the supplied adapter cover for theft

prevention.

USB wireless adapter:

USB-WL-11N

Temperature range: 0 ~ 45°C(operating)

1. Loosen the screw on the bottom left of the WIRELESS port.

2. Insert the tab of the cover into the hole at the upper right of the WIRELESS

port in the direction of the arrow.

3. Align the screw holes on the projector and the cover. Then insert the screw

removed from the projector into the hole and tighten the screw.

Fastening the adapter cover

WIRELESS DC5V 0.5A

LAN

Tab

WIRELESS DC5V 0.5A

LAN

WARNING ►Keep small parts away from children and pets. Take care not

to put in the mouth.

►Heat may build up in the USB wireless adapter, to avoid possible burns

disconnect the projector power cord for 10 minutes before touching the adapter.

Andere Handbücher für CP-WU8700

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hitachi Projektor Handbücher

Hitachi

Hitachi CP-X2010 series Technisches Dokument

Hitachi

Hitachi Innovate CP-RX78 Bedienungsanleitung

Hitachi

Hitachi CP-X255 Bedienungsanleitung

Hitachi

Hitachi CP-TW2505 Bedienungsanleitung

Hitachi

Hitachi CP-X8150 Bedienungsanleitung

Hitachi

Hitachi X308 - CP XGA LCD Projector Technisches Dokument

Hitachi

Hitachi CP-SX12000 Bedienungsanleitung

Hitachi

Hitachi 8755J Bedienungsanleitung

Hitachi

Hitachi CP-S317 Bedienungsanleitung

Hitachi

Hitachi CP-AW250N Bedienungsanleitung

Hitachi

Hitachi CP-WX625 Technisches Dokument

Hitachi

Hitachi CP-TW2503 Bedienungsanleitung

Hitachi

Hitachi CP-X955W Bedienungsanleitung

Hitachi

Hitachi CP-WX3530WN Bedienungsanleitung

Hitachi

Hitachi Innovate iPJ-AW250NM Bedienungsanleitung

Hitachi

Hitachi X253 - CP XGA LCD Projector Bedienungsanleitung

Hitachi

Hitachi CP-A220N Bedienungsanleitung

Hitachi

Hitachi CP-X2542WN Bedienungsanleitung

Hitachi

Hitachi X308 - CP XGA LCD Projector Leitfaden

Hitachi

Hitachi CP-AW250N Bedienungsanleitung

Hitachi

Hitachi Innovate CP-X2520 Bedienungsanleitung

Hitachi

Hitachi Performa CP-RS55 Bedienungsanleitung

Hitachi

Hitachi CP-DX300 guide Installationsanleitung

Hitachi

Hitachi CP-WX625 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung