Hitachi CP-X1250J Bedienungsanleitung

Projector

ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

ITALANO

NORSK

NEDERLANDS

PORTUGUÊS

SVENSKA

SUOMI

POLSKI

SAFETYINSTRUCTIONS（5A）03.12.58:48AMページ1

Projector

User's Manual - Safety Guide

About The Symbols

Various symbols are used in this manual, the user’s manual and on the product itself to

ensure correct usage, to prevent danger to the user and others, and to prevent property

damage. The meanings of these symbols are described below. It is important that you

read these descriptions thoroughly and fully understand the contents.

Typical Symbols

This symbol indicates an additional warning (including cautions). n illustration is

provided to clarify the contents.

This symbol indicates a prohibited action. The contents will be clearly indicated

in an illustration or nearby (the symbol to the left indicates that disassembly is

prohibited).

This symbol indicates a compulsory action. The contents will be clearly

indicated in an illustration or nearby (the symbol to the left indicates that the

power plug should be disconnected from the power outlet).

WARNING

This symbol indicates information that, if ignored, could

possibly result in personal injury or even death due to

incorrect handling.

CAUTION

This symbol indicates information that, if ignored, could

result possibly in personal injury or physical damage due to

incorrect handling.

Thank you for purchasing this projector.

• The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in this

manual

• The reproduction, transmission or use of this document or contents is not permitted

without express written authority.

NOTE

WARNING • Before usin , read these user's manuals of this projector to ensure

correct usa e throu h understandin . After readin , store them in a safe place for

future reference. Incorrect handlin of this product could possibly result in personal injury

or physical dama e. The manufacturer assumes no responsibility for any dama e caused by

mishandlin that is beyond normal usa e defined in these manuals of this projector.

SAFETYINSTRUCTIONS（5A）03.12.58:48AMページ1

Safety Precautions

WARNING

Never use the projector if a problem should occur.

bnormal operations such as smoke, strange odor, no image, no sound,

excessive sound, damaged casing or elements or cables, penetration of

liquids or foreign matter, etc. can cause a fire or electrical shock.

In such case, immediately turn off the power switch and then disconnect the

power plug from the power outlet. fter making sure that the smoke or odor

has stopped, contact your dealer. Never attempt to make repairs yourself

because this could be dangerous.

• The power outlet should be close to the projector and easily accessible.

Use special caution for children and pets.

Incorrect handling could result in fire, electrical shock, injury, burn or

vision problem.

Use special caution in households where children and pets are present.

Do not insert liquids or forei n object.

Penetration of liquids or foreign objects could result in fire or electrical

shock. Use special caution in households where children are present.

If liquids or foreign object should enter the projector, immediately turn off

the power switch, disconnect the power plug from the power outlet and

contact your dealer.

• Do not place the projector in a bathroom.

• Do not expose the projector to rain or moisture.

• Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc

on or around the projector.

• Do not place metals, combustibles, etc on or around the projector.

• To avoid penetration of foreign objects, do not put the projector into a case

or bag together with any thing except the accessories of the projector,

signal cables and connectors.

Never disassemble and modify.

The projector contains high voltage components. Modification and/or disassembly

of the projector or accessories could result in fire or electrical shock.

• Never open the cabinet.

• sk your dealer to repair and clean insider.

Do not ive the projector any shock or impact.

If the projector should be shocked and/or broken, it could result in an injury,

and continued use could result in fire or electrical shock.

If the projector is shocked, immediately turn off the power switch,

disconnect the power plug from the power outlet and contact your dealer.

Do not place the projector on an unstable surface.

If the projector should be dropped and/or broken, it could result in an injury,

and continued use could result in fire or electrical shock.

• Do not place the projector on an unstable, slant or vibrant surface such as

a wobbly or inclined stand.

• Use the caster brakes placing the projector on a stand with casters.

• Do not place the projector in the side up position, the lens up position or

the lens down position.

• In the case of a ceiling installation or the like, contact your dealer before

installation.

Disconnect the

plug from the

power outlet.

Do not

disassemble.

SAFETYINSTRUCTIONS（5A）03.12.58:48AMページ2

WARNING

Be cautious of Hi h temperatures of the projector.

High temperatures are generated when the lamp is lit. It could result in fire

or burn. Use special caution in households where children are present.

Do not touch about the lens, air fans and ventilation openings during use or

immediately after use, to prevent a burn. Take care of ventilation.

• Keep a space of 30 cm or more between the sides and other objects such

as walls.

• Do not place the projector on a metallic table or anything weak in heat.

• Do not place anything about the lens, air fans and ventilation openings of

the projector.

• Do not use with the ventilation opening facing downwards.

• Never block the air fan and ventilation openings.

• Do not cover the projector with a tablecloth, etc.

• Do not place the projector on a carpet or bedding.

Never look throu h the lens or openin s when the lamp is on.

The powerful light could adversely affect vision.

Use special caution in households where children are present.

Use only the correct power cord and the correct power outlet.

Incorrect power supply could result in fire or electrical shock.

• Use only the correct power outlet depending on the indication on the

projector and the safety standard.

• The enclosed power cord must be used depending on the power outlet to

be used.

Be cautious of the power cord connection.

Incorrect connection of the power cord could result in fire or electrical

shock.

• Do not touch the power cord with a wet hand.

• Check that the connecting portion of the power cord is clean (with no

dust), before using. Use a soft and dry cloth to clean the power plug.

• Insert the power plug into a power outlet firmly. void using a loose,

unsound outlet or contact failure.

Be sure to connect with round wire.

Connect the ground terminal of C inlet of this unit with the ground

terminal provided at the building using the correct power cord; otherwise,

fire or electric shock can result.

• Don’t take the core of power cord away.

Safety Precautions (continued)

Surely connect

the ground wire.

SAFETYINSTRUCTIONS（5A）03.12.58:48AMページ3

WARNING

Be careful in handlin the li ht source lamp.

The projector uses a high-pressure mercury glass lamp made of glass. The

lamp can break with a loud bang, or burn out. When the bulb bursts, it is

possible for shards of glass to fly into the lamp housing, and for gas

containing mercury to escape from the projector’s vent holes.

Please carefully read the section “Lamp”.

Be careful in handlin the power cord and external connection cables.

If you keep using a damaged the power cord or cables, it can cause a fire or

electrical shock. Do not apply too much heat, pressure or tension to the

power cord and cables.

If the power cord or cables is damaged (exposed or broken core wires, etc.),

contact your dealer.

• Do not place the projector or heavy objects on the power cord and cables.

lso, do not place a spread, cover, etc, over them because this could result

in the inadvertent placing of heavy objects on the concealed power cord or

cables.

• Do not pull the power cord and cables. When connecting and

disconnecting the power cord or cables, do it with your hand holding the

plug or connector.

• Do not place the cord near the heater.

• void bending the power cord sharply.

• Do not attempt to work on the power cord.

Be careful in handlin the battery of the remote control.

Incorrect handling of the battery could result in fire or personal injury. The

battery may explode if not handled properly.

• Keep the battery away from children and pets. If swallowed consult a

physician immediately for emergency treatment.

• Do not allow the battery in a fire or water.

• void fire or high-temperature environment.

• Do not hold the battery with the metallic tweezers.

• Keep the battery in a dark, cool and dry play.

• Do not short circuit the battery.

• Do not recharge, disassemble or solder the battery.

• Do not give the battery a physical impact.

• Use only the battery specified in the other manual of this projector.

• Make sure the plus and minus terminals are correctly aligned when

loading the battery.

• If you observe a leakage of the battery, wipe out the flower and then

replace the battery. If the flower adheres your body or clothes, rinse well

with water.

• Obey the local laws on disposing the battery.

Safety Precautions (continued)

SAFETYINSTRUCTIONS（5A）03.12.58:48AMページ4

Safety Precautions (continued)

CAUTION

Be careful in movin the projector.

Neglect could result in an injury or damage.

• Do not move the projector during use. Before moving, disconnect the

power cord and all external connections, and close the slide lens door or

attach the lens cap.

• void any impact or shock to the projector.

• Do not drag the projector.

• For moving the projector, use the enclosed case or bag if provided.

Do not put anythin on top of the projector.

Placing anything on the projector could result in loss of balance or falling,

and cause an injury or damage. Use special caution in households where

children are present.

Do not attach anythin other than specified thin s to the projector.

Neglect could result in an injury or damage.

• Some projector has a screw thread in a lens part. Do not attach anything

other than specified options (such as conversion lens) to the screw thread.

Avoid a smoky, humid or dusty place.

Placing the projector in a smoke, a highly humid, dusty place, oily soot or

corrosive gas could result in fire or electrical shock.

• Do not place near the smoking space, the kitchen or a humidifier.

Take care of the air filter to normal ventilate.

The air filter should be cleaned periodically. If the air filter becomes

clogged by dust or the like, internal temperature rises and could cause

malfunction. The projector may display the message such as “CHECK THE

IR FLOW” or turn off the projector, to prevent the internal heat level

rising.

• When the indicators or a message prompts you to clean the air filter, clean

the air filter as soon as possible.

• If the soiling will not come off the air filter, or it becomes damaged,

replace the air filter.

• Use the air filter of the specified type only. Please order the air filter

specified in the other manual of this projector to your dealer.

• When you replace the lamp, replace also the air filter. The air filter may be

attached when you buy a replacement lamp for this projector.

• Do not turn on the projector without air filter.

Avoid a hi h temperature environment.

The heat could have adverse influence on the cabinet of the projector and

other parts. Do not place the projector, the remote control and other parts in

direct sunlight or near a hot object such as heater, etc.

Remove the power cord for complete separation.

• For safety purposes, disconnect the power cord if the projector is not to be

used for prolonged periods of time.

• Before cleaning, turn off and unplug the projector. Neglect could result in

fire or electrical shock.

Disconnect the

plug from the

power outlet.

SAFETYINSTRUCTIONS（5A）03.12.58:48AMページ5

Safety Precautions (continued)

NOTE

Do not ive the remote control any physical impact.

physical impact could cause damage or malfunction of the remote control.

• Take care not to drop the remote control.

• Do not place the projector or heavy objects on the remote control.

Take care of the lens.

• Close the slide lens door or attach the lens cap to prevent the lens surface being

scratched when the projector is not used.

• Do not touch the lens to prevent fog or dirt of the lens that cause deterioration of display

quality.

• Use commercially available lens tissue to clean the lens (used to clean cameras,

eyeglasses, etc.). Be careful not to scratch the lens with hard objects.

Take care of the cabinet and the remote control.

Incorrect care could have adverse influence such as discoloration, peeling paint, etc.

• Use a soft cloth to clean the cabinet and control panel of the projector and the remote

control. When excessively soiled dilute a neutral detergent in water, wet and wring out the

soft cloth and afterward wipe with a dry soft cloth. Do not use undiluted detergent

directly.

• Do not use an aerosol sprays, solvents, volatile substances or abrasive cleaner.

• Before using chemical wipes, be sure to read and observe the instructions.

• Do not allow long-term close contact with rubber or vinyl.

About bri ht spots or dark spots.

lthough bright spots or dark spots may appear on the screen, this is a unique characteristic of

liquid crystal displays, and such do not constitute or imply a machine defect.

Be careful of printin of the LCD panel.

If the projector continues projecting a still image, inactive images or 16:9 aspect images

in case of 4:3 panel, etc., for long time, the LCD panel might possibly be printed.

In such a case, please make the projector project a whole white screen for 1 hour or more.

You can use the BL NK function of the projector.

About consumables.

Lamp, LCD panels, polarizors and other optical components, and air filter and cooling

fans have a different lifetime in each. These parts may need to be replaced after a long

usage time, even if one year has not passed since the beginning of using. For more details,

please consult your dealer.

CAUTION

Ask your dealer to cleanin inside of the projector about every two

years.

ccumulations of dust inside the projector cause result in fire or

malfunction. Cleaning inside is more effective if performed before every

humid periods such as rainy season.

• Do not clean inside yourself because it is dangerous.

SAFETYINSTRUCTIONS（5A）03.12.58:48AMページ6

Safety Precautions (continued)

NOTE

Avoid stron rays.

Any strong ray (such as direct rays of the sun or room lighting) onto the remote control

sensors could invalidate the remote control.

Avoid radio interference.

ny interfering radiation could cause disordered image or noises.

• void radio generator such as a mobile telephone, transceiver, etc. around the projector.

About displayin characteristic.

The display condition of the projector (such as color, contrast, etc.) depends on

characteristic of the screen, because the projector uses a liquid crystal display panel. The

display condition can differ from the display of CRT.

• Do not use a polarized screen. It can cause red image.

Turn the power on/off in ri ht order.

To prevent any trouble, turn on/off the projector in right order mentioned below unless

specifying.

• Power on the projector before the computer or video tape recorder.

• Power off the projector after the computer or video tape recorder.

Take care not to fati ue your eyes.

Rest the eyes periodically.

Set the sound volume at a suitable level to avoid botherin other people.

• It is better to keep the volume level low and close the windows at night to protect the

neighborhood environment.

Connectin with notebook computer

When connecting with notebook computer, set to valid the RGB external image output

(setting CRT display or simultaneous display of LCD and CRT).

Please read instruction manual of the notebook for more information.

SAFETYINSTRUCTIONS（5A）03.12.58:48AMページ7

Lamp

The projector uses a high-pressure mercury glass lamp. The lamp can break with a

loud ban , or burn out, if jolted or scratched, handled while hot, or worn over time.

Note that each lamp has a different lifetime, and some may burst or burn out soon after

you start using them. In addition, when the bulb bursts, it is possible for shards of

lass to fly into the lamp housing, and for as containin mercury to escape from the

projector’s vent holes.

About disposal of a lamp • This product contains a mercury lamp; do not put in trash.

Dispose of in accord with environmental laws.

For lamp recycling, go to www.lamprecycle.org. (in US )

For product disposal, contact your local government agency or www.eiae.org (in the

US) or www.epsc.ca (in Canada).

For more information, call your dealer.

• If the lamp should break (it will make a loud bang when it does), unplug

the power cord from the outlet, and make sure to request a replacement

lamp from your local dealer. Note that shards of glass could damage the

projector’s internals, or cause injury during handling, so please do not try

to clean the projector or replace the lamp yourself.

• If the lamp should break (it will make a loud bang when it does),

ventilate the room well, and make sure not to breathe the gas that comes

out of the projector vents, or get it in your eyes or mouth.

• Before replacing the lamp, make sure the power switch is off and the

power cable is not plugged in, then wait at least 45 minutes for the lamp

to cool sufficiently. Handling the lamp while hot can cause burns, as well

as damaging the lamp.

• Do not open the lamp cover while the projector is suspended from above.

This is dangerous, since if the lamp’s bulb has broken, the shards will

fall out when the cover is opened. In addition, working in high places is

dangerous, so ask your local dealer to have the lamp replaced even if the

bulb is not broken.

• Do not use the projector with the lamp cover removed. t the lamp

replacing, make sure that the screws are screwed in firmly. Loose screws

could result in damage or injury.

• Use the lamp of the specified type only.

• If the lamp breaks soon after the first time it is used, it is possible that

there are electrical problems elsewhere besides the lamp. If this happens,

contact your local dealer or a service representative.

• Handle with care: jolting or scratching could cause the lamp bulb to burst

during use.

• If the indicators or a message prompts you to replace the lamp (see the

section “Related Messages” and “Regarding the indicator Lamps”),

replace the lamp as soon as possible. Using the lamp for long periods of

time, or past the replacement date, could cause it to burst. Do not use old

(used) lamps; this is a cause of breakage.

WARNING HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE

Disconnect the

plug from the

power outlet

SAFETYINSTRUCTIONS（5A）03.12.58:48AMページ8

Re ulatory Notices

FCC Statement Warnin

WARNING: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

INSTRUCTIONS TO USERS: This equipment complies with the requirements of FCC

(Federal Communication Commission) equipment provided that the following conditions

are met. Some cables have to be used with the core set. Use the accessory cable or a

designated-type cable for the connection. For cables that have a core only at one end,

connect the core to the projector.

CAUTION: Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

For the Customers in CANADA

NOTICE: This Class B digital apparatus complies with Canadian ICES-003.

Warranty And After-Service

Unless seen any abnormal operations (mentioned with the first paragraph of W RNING

in this manual), when a problem occurs with the equipment, first refer to the

“Troubleshooting” section of the “User’s manual – Operating Guide”, and run through the

suggested checks.

If this does not resolve the problem contact your dealer or service company. They will tell

you what warranty condition is applied.

SAFETYINSTRUCTIONS（5A）03.12.58:48AMページ9

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hitachi Projektor Handbücher

Hitachi

Hitachi CP-X995W Bedienungsanleitung

Hitachi

Hitachi CP-S318 series Bedienungsanleitung

Hitachi

Hitachi CPWX8 Technisches Dokument

Hitachi

Hitachi CP-WX3030WN Bedienungsanleitung

Hitachi

Hitachi CPX7 Bedienungsanleitung

Hitachi

Hitachi CP-D31N guide Bedienungsanleitung

Hitachi

Hitachi CP-SX5500W Bedienungsanleitung

Hitachi

Hitachi CP-S235 Bedienungsanleitung

Hitachi

Hitachi CP-X264 and Technisches Dokument

Hitachi

Hitachi ED-D11N Bedienungsanleitung

Hitachi

Hitachi CP-X2020 Bedienungsanleitung

Hitachi

Hitachi CP-S370W Bedienungsanleitung

Hitachi

Hitachi Innovate ED-A111 Bedienungsanleitung

Hitachi

Hitachi CP-SX635 - SXGA+ LCD Projector Technisches Dokument

Hitachi

Hitachi ED-A100 Installations- und Betriebsanleitung

Hitachi

Hitachi CP-X325W Bedienungsanleitung

Hitachi

Hitachi Innovate CP-AW100N Bedienungsanleitung

Hitachi

Hitachi CP-X2514WN Bedienungsanleitung

Hitachi

Hitachi X807 - CP XGA LCD Projector Bedienungsanleitung

Hitachi

Hitachi X308 - CP XGA LCD Projector Bedienungsanleitung

Hitachi

Hitachi CP-X809 Bedienungsanleitung

Hitachi

Hitachi CP-X3 Bedienungsanleitung

Hitachi

Hitachi CP-AW250N Bedienungsanleitung

Hitachi

Hitachi 8755H Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung