Hitachi Compute Rack CR 210H Bedienungsanleitung

CR210H / CR220H Log Collection

The customer and/or CE should be connected directly to the maintenance port to obtain logs.

Note: This model server does not have a pre-configured IP address similar to the CR220xK. So the IP address be

requested in step 2 would need to have been setup by the CE or customer prior. If assistance is needed with this,

please contact support or your local CE.

1. Launch the browser of the administrative system console terminal.

2. Enter "http://<IP Address>" in the address. (As for the IP address, consult customers.)

The factory default settings of the network of the management interface are as follows.

IP address : Not set

Subnet mask : Not set

Default gateway : Not set

DHCP : used

3. When the connection is successfully established, the login screen is displayed in the browser.

4. Select the [Logs] tab, and press the [Download Logs] button.

5. Save the file and upload to TUF.

https://tuf.hitachivantara.com/upload.php

Alternative Method

If unable to use specified IP address for server or it is unknown, you can place the server into 'maintenance' mode.

1. When the LAN cable of the customer is connected to the management interface connector, check that the Web

Console function is not used by the customer, and ask the customer to disconnect the cable.

2. To set the management interface to maintenance mode, hold down the 'FN' button (Function) for 10 seconds or

more until the ERROR LED begins to blink.

https://knowledge.hitachivantara.com/Support_Information/Data_Collection/Servers/CR210H__CR220H_Log_Collection

Updated: Fri, 19 May 2023 00:38:22 GMT

The server is in maintenance mode when the ERROR LED is blinking.

(If the management interface is connected to LAN, it cannot be set to the maintenance mode.)

The factory default settings of the network of the management interface are as follows.

IP address : 192.168.0.1

Subnet mask : 255.255.255.0

Default gateway : Not set

DHCP : disabled

In the maintenance mode, ERROR LED is blinking.

When one of the following conditions is satisfied, the maintenance mode is canceled.

- In the maintenance mode, the FUNCTION BUTTON is pressed for 10 seconds or more until the ERROR LED

stops blinking.

- The maintenance mode continues for about 30 minutes.

When the maintenance mode is canceled, ERROR LED returns to the original status.

Note that the maintenance mode is not canceled by rebooting the system, turning the system off, or disconnecting

the AC power supply.

3. The mainenance operator connects the PC for maintenance to the management interface connector with a LAN

cross cable.

4. Launch the browser of the administrative system console terminal.

5. Enter "http://192.168.0.1" in the address.

6. When the connection is successfully established, the following login screen is displayed in the browser.

7. Select the [Logs] tab, and press the [Download Logs] button to save the logs collected by BMC.

8. Save the file and upload to TUF.

https://tuf.hitachivantara.com/upload.php

9. Press the [Logout] button in the upper-right of the screen to log out from Web Console.

If the user does not log out and closes the browser, the status that the user logs in continues until the user is

automatically logged out in about 30 minutes.

Therefore, each time the user closes the browser without log out, a new user cannot log in until 30 minutes has

elapsed.

10. Remove the LAN cross-over cable from the management interface connector.

11. Keep pressing the Function switch for 10 seconds or more to cancel the maintenance mode. Check that ERROR

LED is not blinking.

When the maintenance mode is canceled, ERROR LED returns to the original status.

When one of the following conditions is satisfied, the maintenance mode is canceled.

- In the maintenance mode, the Function switch is pressed for 10 seconds or more.

- The maintenance mode continues for about 30 minutes.

Note that the maintenance mode is not canceled by rebooting the system, turning the system off, or disconnecting

the AC power supply.

12. If customer's LAN cable was connected to the management interface connector before, ask the customer to

reconnect the cable. ask the customer to reconnect the cable, ask the customer to reconnect the cable.

https://knowledge.hitachivantara.com/Support_Information/Data_Collection/Servers/CR210H__CR220H_Log_Collection

Updated: Fri, 19 May 2023 00:38:22 GMT

Andere Handbücher für Compute Rack CR 210H

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hitachi Server Handbücher

Hitachi

Hitachi HA805 G3 Series Bedienungsanleitung

Hitachi

Hitachi HA820 G3 Series Bedienungsanleitung

Hitachi

Hitachi HA810 G3 Series Bedienungsanleitung

Hitachi

Hitachi Compute Blade Series Allgemeine Anweisungen

Hitachi

Hitachi HA825 G3 Series Bedienungsanleitung

Hitachi

Hitachi Content Platform S Series Bedienungsanleitung

Hitachi

Hitachi VSP F1500 Bedienungsanleitung

Hitachi

Hitachi Compute Rack CR 210H Bedienungsanleitung

Hitachi

Hitachi Compute Blade 2000 Bedienungsanleitung

Hitachi

Hitachi DS225 Montageanleitung

Hitachi

Hitachi HA800 G3 Series Bedienungsanleitung

Hitachi

Hitachi Compute Blade 2500 Bedienungsanleitung

Hitachi

Hitachi Compute Blade 500 Series Bedienungsanleitung

Hitachi

Hitachi DS7000 Series Bedienungsanleitung

Hitachi

Hitachi VisionBase 8880R Bedienungsanleitung

Hitachi

Hitachi Advanced Server DS220 Montageanleitung

Hitachi

Hitachi DS240 Bedienungsanleitung

Hitachi

Hitachi Compute Blade 500 Series Bedienungsanleitung

Hitachi

Hitachi DS7000 Series Bedienungsanleitung

Hitachi

Hitachi Compute Blade 500 Series Bedienungsanleitung

Hitachi

Hitachi HVM Navigator V03-06 Bedienungsanleitung

Hitachi

Hitachi Compute Rack 220H Stücklistenhandbuch

Hitachi

Hitachi HNAS 3080 Benutzerhandbuch

Hitachi

Hitachi HA820 G2 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung