HITVIS HT811WP Bedienungsanleitung

Indoor HD P2P WIFI Camera

User Manual

www.hitvis.com

Model: HT811WP

V1.0

Please read and understand the following safety sheet before you use the

monitor.

This camera is designed for indoor usage only,between -10 °~55° C.

Keep this camera out of direct sunlight.

Only use the provided power adapter with this camera.

Keep the camera,power adapter,and accessories out of the reach of

children and pets.

1 Read Before Use

2 Packing Contents

WIFI CAMX1

Warranty Card x1

3 Device Overviews

Mounting Bracket x1

User Manual x1

Power Adapter x 1

1---Flash lamp 2---Monitor Lens 3---LED light

4---Microphone 5---Magnetic base 6---Record

7--- WPS 8---Reset 9--- DC power

The status of LED light

No light: No power supplied to the monitor.

Keep green light: Camera is starting up.

Blinking red light about once every second: Camera is under AP mode.

Blinking green light about once every second: Camera has connected

to a wifi network and under STA mode.

Blinking green light about two times every second: Camera is recording

after you press the record button on the back of the camera.

Alternately flashes green and red light: Camera is connecting to a wifi

network after you pressed the WPS button.

Blinking red light quickly about two times every second: The network

has some problem and the camera cannot connect to the network.

Keep red light on: The camera has some problem and can’t start well.

Press and hold this button for one second, the led light will turn to green

and blink quickly, the camera starts recording and stores the record file

to micro SD card. Press and hold this button for one second again, it

stops recording. Make sure the camera has inserted micro SD card.

WPS

Step1:

Press and hold the WPS button for one second , and you will see the led

light flashes green and red light alternately.

Step2:

Press the WPS button on your router within 60 seconds. The WPS button

is usually on the front side of your router. If you are not sure where the

WPS button is on your router, please refer to your router’s User Manual.

The HT811WP will automatically create a secure wireless connection to

your router. After connected successfully, the led in your camera will blink

green.

Record

Reset

Press and hold the Reset button for 3 seconds to reset the camera to

factory default settings.

Micro SD card slot

Support up to 32G. You’d better insert or takeout

micro SD card when the camera without the power.

But if you inset the micro SD card while the camera

is running ,please reboot the camera (unplug the

power, then plug it again), or else the micro sd card

may be cannot work well.

The new file will recover the oldest file when there

is no space in the micro SD card.

4 Mounting the camera

Mount the camera on the wall or fix it at the celling.

5 Softeware Installation

Search for HITVIS app to download and install the app on your phone

when connected to the Internet.

You can also download the Android app from our website .

Step 1

Power the camera, the LED light will turn to green . Wait for 5 seconds,

the light will turn to red and flash about once every second.

7 Live view

Step 2 Start the App.

Tap our phone app icon and start the program. First time using the app,

you will go to our guide interface as figure 1.

Click Next--Next , you can go to the following screen as figure 2 .

As a new user, please tap “New user” and do as our guide information.

6 AP and STA mode

AP mode: This is the default mode, your camera acts as an central

connection point, which wireless devices can connect to.

Under this mode, you can connect directly to your camera, which means

there is no need for an Internet connection or a router. You can view the

camera in LAN.

STA mode: Connect HT811WP to your home wifi network.

You can go to page 17 to read how to view the camera under AP or STA

mode.

AP and STA modes cannot exist at the same time. One time only one

mode takes effect.

The wifi camera supports AP and STA mode, what’s the difference?

Note

Step 3 Connect monitor to a wi-fi network

Tap “ Enjoy now ”(Figure 3) , App will search the device in LAN

automatically(Figure 4). Tap “Sure” , then select “Start” .(Figure 5)

Figure 1 Figure 2

Figure 3 Figure 4

Figure 5

Tap the device ID you want to configure as figure 6, you can also see the

ID No. (for example: S98214258) in your color box.

Figure 6

Next you can connect your camera to a wifi network.

Figure 7 Figure 8

Click the SSID of your router in the list, the router SSID will be filled in the

top box automatically, you only need to fill in the sharekey. Make sure that

SSID and share key you filled in the camera exactly the same for your

router. Then tap “Configure” to finish configuration(Figure 7,8) .

Wait for 30 seconds, you can see the LED light of the camera turns to

green and flashes once every second which means the camera configured

successfully.

Step 4 Live view

Regist an App acount to manage your devices.(Figure 9)

Click “Confirm” and add you device to the app(Figure 10).

The device ID will filled automatically, you don’t need to change it, or else

you can not connect the device successfully. If you tap “Setting”, you can

see you need to fill the username and password. The default device

username is admin with no password. But for the first time using, you can

tap “Save” icon to add device without filling it. (Figure 11)

Figure 9 Figure 10

Figure 11

For the first time using, you must reset the username and password to

avoid unauthorized users. (Figure 12) Tap “Save” to save settings.

Please remember the device username and password , you only have

this chance to change it. Next time you want to reset the username

or password, you must reset the camera.

After changing the device username and password, you will go to “ My

video ” page automatically, tap the device , and you can enjoy live video.

Figure 12

Note

Figure 13 Figure 14

8 Advanced App Setting

Phone app support two login modes: Visitor login and Account login.

For Visitor, you don’t need to register an app account, you can tap Visitor

an app account, fill in the username and password before login, and your

phone must connect internet.

Some functions you can’t use under Visitor login mode, such as alarm

message receiver, advanced settings about the camera you added, scene

picture and so go. So here we suggest you using Account login mode.

Username / Password: The username and password you registered in

app.

account.

Inhaltsverzeichnis

Beliebte IP-Kamera Handbücher anderer Marken

FLIR

FLIR Exx series Bedienungsanleitung

Avigilon

Avigilon H4A-BO1-IR Bedienungsanleitung

Digital Watchdog

Digital Watchdog DWCA-C128-64 Bedienungsanleitung

ShareTech

ShareTech AV1 Bedienungsanleitung

Ezviz

Ezviz C6C Bedienungsanleitung

Melchioni

Melchioni UCAM 2015 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/ESD-4630 Bedienungsanleitung

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Bedienungsanleitung

Mitel

Mitel 6800i Series Service-Handbuch

Vitek

Vitek VTC-IR403-212NP Bedienungsanleitung

THOMSON

THOMSON DSC - 323W Bedienungsanleitung

AVer

AVer FB2027 Bedienungsanleitung

ENFORCER

ENFORCER EV-T5105-N2SQ Bedienungsanleitung

Wansview

Wansview NC543 Bedienungsanleitung

Eneo

Eneo MCB-64A0003M0A Bedienungsanleitung

deView electronics

deView electronics CBDNI36F Bedienungsanleitung

Swann

Swann SwannEye Bedienungsanleitung

LevelOne

LevelOne IP CamSecure Bedienungsanleitung