HMS Anybus AWB4004 Benutzerhandbuch
Anybus®WLAN Access Point IP67
STARTUP GUIDE
SP2383 1.3 en-US ENGLISH
Important User Information
Disclaimer
The information in this document is for informational purposes only. Please inform HMS Industrial
Networks of any inaccuracies or omissions found in this document. HMS Industrial Networks disclaims
any responsibility or liability for any errors that may appear in this document.
HMS Industrial Networks reserves the right to modify its products in line with its policy of continuous
product development. The information in this document shall therefore not be construed as a
commitment on the part of HMS Industrial Networks and is subject to change without notice. HMS
Industrial Networks makes no commitment to update or keep current the information in this document.
The data, examples and illustrations found in this document are included for illustrative purposes and are
only intended to help improve understanding of the functionality and handling of the product. In view of
the wide range of possible applications of the product, and because of the many variables and
requirements associated with any particular implementation, HMS Industrial Networks cannot assume
responsibility or liability for actual use based on the data, examples or illustrations included in this
document nor for any damages incurred during installation of the product. Those responsible for the use
of the product must acquire sufficient knowledge in order to ensure that the product is used correctly in
their specific application and that the application meets all performance and safety requirements
including any applicable laws, regulations, codes and standards. Further, HMS Industrial Networks will
under no circumstances assume liability or responsibility for any problems that may arise as a result from
the use of undocumented features or functional side effects found outside the documented scope of the
product. The effects caused by any direct or indirect use of such aspects of the product are undefined
and may include e.g. compatibility issues and stability issues.
Anybus®WLAN Access Point IP67 Startup Guide SP2383 1.3 en-US
Anybus®WLAN Access Point IP67 Startup Guide SP2383 1.3 en-US
Table of Contents Page
1 About This Document . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . .. . 3
1.1 Document Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Safety ...................................................................... 4
2.1 General Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2 Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3 5 GHz Transmission Power Restriction (EU only). . . . . . . . . . . . . . . . . . . . . . . . . . 5
3 Installation................................................................. 6
3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2 Wall Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.3 Pole Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.4 Power Connector (M12) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.5 Ethernet Connector (M12) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.6 Ethernet Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.7 Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.8 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4 Configuration .............................................................14
4.1 Factory Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5 Technical Data ............................................................15
5.1 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.2 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
This page intentionally left blank
About This Document 3 (18)
1 About This Document
This document describes how to install Anybus WLAN Access Point IP67.
For additional documentation and software downloads, FAQs, troubleshooting
guides and technical support, please visit www.anybus.com/support.
1.1 Document Conventions
The following conventions are used to indicate safety information and other
important content in this document:
WARNING
Instruction that must be followed to avoid a risk of death or serious injury.
Caution
Instruction that must be followed to avoid a risk of personal injury.
Instruction that must be followed to avoid a risk of reduced functionality
and/or damage to the equipment, or to avoid a network security risk.
Additional information which may facilitate installation and/or operation.
Anybus®WLAN Access Point IP67 Startup Guide SP2383 1.3 en-US
Safety 4 (18)
2 Safety
2.1 General Safety Instructions
Caution
This equipment emits RF energy in the ISM (Industrial, Scientific, Medical)
band. Make sure that all medical devices used in proximity to this device
meet appropriate susceptibility specifications for this type of RF energy.
This product contains parts that can be damaged by electrostatic
discharge (ESD). Use ESD prevention measures to avoid damage.
To prevent water intrusion, make sure that the unit is installed with the
connectors on the bottom panel of the unit facing down.
2.2 Intended Use
The intended use of this equipment is as a communication interface and
gateway. The equipment receives and transmits data on various physical levels
and connection types.
If this equipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment may be impaired.
Anybus®WLAN Access Point IP67 Startup Guide SP2383 1.3 en-US
Safety 5 (18)
2.3 5 GHz Transmission Power Restriction (EU only)
Transmission power must be reduced for 5 GHz channels 149-165 when
the unit is used in the EU.
To comply with the European Radio Equipment Directive (RED) the effective
radiated power output for 5 GHz channels 149-165 (U-NII-3) must not exceed
25 mW (~14 dBm) when the unit is used in the EU.
To configure the unit for use within the EU, set Tx Power to 14 dBm or less on
the Wireless 1 Options page of the web configuration interface.
Fig. 1 Wireless Settings
Anybus®WLAN Access Point IP67 Startup Guide SP2383 1.3 en-US
Installation 6 (18)
3 Installation
The Anybus WLAN Access Point IP67 can be screw-mounted onto a stable flat
surface using the included wall mounting kit. It can also be pole-mounted using
the included adjustable steel band straps.
For optimal reception, wireless devices require a zone between them clear of
objects that could otherwise obstruct or reflect the signal. A minimum distance
of 50 cm between the devices should also be observed to avoid interference.
Make sure that you have all the necessary information about the capabilities
and restrictions of your local network environment before installation.
Package Contents
After unpacking the access point, check the contents to be sure you have
received all the components:
• Anybus WLAN Access Point IP67 (1 x)
• Wall mounting kit (1 x)
– Mounting plate (1 x)
– Screw 5.8 mm x 14.8 mm for fixed mounting plate (4 x)
– Screw 6.3 mm x 25.3 mm for wall mount (4 x)
• Steel band strap (2 x)
• Antenna (2 x)
• Grounding cable (1x)
• Grounding screw with washer (2x)
• Startup Guide (1 x)
Anybus®WLAN Access Point IP67 Startup Guide SP2383 1.3 en-US
Installation 8 (18)
3.2 Wall Mounting
Fig. 3 Wall mounting
1. Attach the mounting plate to the back of the unit using the 4 included
screws. The plate can be attached vertically or horizontally.
2. Hold the unit upright against the wall and fasten it with 4 screws through
the apertures in the plate.
Anybus®WLAN Access Point IP67 Startup Guide SP2383 1.3 en-US
Inhaltsverzeichnis
Andere HMS Drahtloser Zugangspunkt Handbücher
Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung
Ubiquiti
Ubiquiti NanoStation NSM2 Bedienungsanleitung
Cisco
Cisco Aironet 1550 Series Bedienungsanleitung
Aruba
Aruba IAP-335 Bedienungsanleitung
Advantek Networks
Advantek Networks AWN-AP-54MR Bedienungsanleitung
IP-COM
IP-COM AP355 Bedienungsanleitung
Buffalo
Buffalo AirStation WLA-L11G Bedienungsanleitung
EnGenius
EnGenius EnStationACv2 Bedienungsanleitung
D-Link
D-Link DAP-3662 Bedienungsanleitung
xG Technology
xG Technology xMax CN1300 Bedienungsanleitung
Widelink
Widelink ezWave WAP-1100 Series Bedienungsanleitung
Edimax
Edimax CAP1200 Bedienungsanleitung
