Hoffmann MORSO NM Bedienungsanleitung
© Hoffmann Machine Company, Inc.
OPERATING MANUAL
for
MORSO manual notching machine
Model NM
Hoffmann Machine Company, Inc.
1386 Drexel Road Valdese, NC 28690 USA
Phone: (828) 430 - 4510 Fax: (828) 430 –4620
e-mail: info@Hoffmann-USA.com
www.Hoffmann-USA.com
Toll-free Technical Support: (866) 248 –0100
Instruction Manual
MORSØ Notch Cutting Machine
Model NM
Contents
Introduction page A-1
Survey page B-1
Work Piece
Cutting of work piece on a
circular saw before notching page C-1
Functional Description:
General Description page D-1
Machine Description page D-2
Technical Data page E-1
Assembly Instructions:
General page F-1
Fitting of Table E tensions
and fences page F-1
Operating Instructions:
Before operating page G-1
Adjustment of Cock-bead Stops page G-2
Adjustment of Centre Stop page G-3
Adjustment of Flip Stops page G-4
Service eferences:
Lubrication Instructions page H-1
Cleaning page H-1
Changing of Knives and
Chip Breakers – Adjustment page H-2
Grinding of Knives page H-3
Changing of Spare Parts page H-4
ectifying Faults
Methods for Repair page I-1
Safety:
Safety Devices page J-1
Regulations page J-1
Spare Part Lists
page K-1 -
page K-7
1
Contents 0-1
Authorized U.S. Importer and Service Center:
Hoffmann Machine Company, Inc.
1386 Drexel oad
Valdese, N.C. 28690
Toll-free: 1 - 866 – 248 – 0100
www.Hoffmann-USA.com
Instruction Manual
MORSØ Notch Cutting Machine
Model NM
2
Introduction A-1
We recommend that you read this instruction manual thoroughly before using this machine.
Damage or faults on the machine caused by misuse or incorrect operation are not covered under our
conditions of warranty.
Use of the Instruction Manual:
The reference system of this Instruction Manual described below will help you to quickly find the
information you require (Picture A-1)
(1) Subject Heading
.
(2) Page Index
The letter (A) refers to the description of the section.
The number (1) refers to the page number of that section.
(3) Text
Description of the subject heading.
Illustration
A three dimensional, numbered drawing of the te t subject. The numbers in the te t korrespond to the
number in the drawing.
Instruction Manual
MORSØ Notch Cutting Machine
Model NM
3
Survey B-1
Survey
Pos. Designation Pos. Designation
1Frame 10 Sliding Stop
2Slide frame 11 Foot Pedal, complete
3Cross 12 Springs (not shown)
4Knife block 13 Table E tensions
5Side Knives 14 Safety Guard
6Nose Knives 15 Centre Stop
7Machine Table 16 Handle
8Fence 17 Chip Breaker (not shown)
9Cock-Bead stop
Instruction Manual
MORSØ Notch Cutting Machine
Model NM
4
Work Piece C-1
Cutting of work piece on a circular saw efore notching
Before the notching of the work piece it must be cut to the correct length on a circular saw.
It is very important that the saw blade is e actly adjusted to 90° to the machine table (see fig. 1). The
blade must also be e actly adjusted to 90° to the fence (see fig. 2).
Discrepancies arising from these cuts will result in gaps in the finished joints.
Fig. 1
Fig. 2
Instruction Manual
MORSØ Notch Cutting Machine
Model NM
5
Functional Description D-1
General Description
MO SØ NM notch cutter is the optimum machine to cut window bars, mullions, and cabinet face-
frames requiring haunch joints.
MO SØ NM is a manual foot-operated machine. The operation is easy.
MO SØ-NM notch cutting machine is provided with 2 sliding longitudinal stops, fi ed fences on both
the right and left side of the machine, nose knife, side knives, chip-breaker, cock-bead stops, centre
stop, and safety guard.
With the MO SØ NM you achieve a smooth, clean, and e act cut by notching the work piece in two
cuts.
This is done manually on the MO SØ-NM.
The forward movement of the knife block is infinitely adjustable.
A special lever system makes the operation of the machine very easy. Twin return springs bring the
knife block back to its home position.
The work pieces can be joined without any further finishing.
Instruction Manual
MORSØ Notch Cutting Machine
Model NM
6
Functional Description D-2
Picture
Picture D-2-1
Machine Description
The MO SØ-NM is constructed as a compact machine with a sturdy frame (1) with foot pedal (11).
The cutting assembly is situated at the top of the machine.
In the slide frame (2) fitted at the cross (3) the knife block (4) is moved up and down. The cross (3)
runs in the guidings of the table.
The knives (5) and nose knife (6) fitted on the knife block cut not only the notch but also cope the
corners to complete the joint.
The forward movement of the knife block is made manually.
The mullion is placed on the table (7) against the fences (8).
The cock-bead stops (9) are adjusted to the required cutting depth of the notch.
The adjustment of the sliding longitudinal stops (10) is done by means of a template of the stile.
Instruction Manual
MORSØ Notch Cutting Machine
Model NM
7
Technical Data
Technical Data
Machine Dimensions (max.): Working Capacity:
Length (a) 1600 mm (63”) Nose Knife Capacity 1.25 – 2,5 cm (½” -1”)
Width (b) 630 mm (25”)
Height (c) 840 mm (33”) Moulding width, ma 115 mm (4.5”)
Weight 50 kg (110 lb) Moulding Thickness, ma . 85 mm (3.3”)
Siting Considerations E tensions Table, left and right 478 mm (19”)
Distance to Wall min.1000 mm (40”) Fences, left and right 00 mm (31.5”)
Noise/Pollution:
Noise Level silent
Pollution nil/no dust
Technical Data E-1
c
a
b
Instruction Manual
MORSØ Notch Cutting Machine
Model NM
8
In General
F-1
Assembly Instructions F-1
Instruction Manual
MORSØ Notch Cutting Machine
Model NM
9
In General
The machine is delivered ready for use and complete with standard equipment.
Only the table e tensions (13) and fences (8) are dismounted during transport.
Place the machine 1 m from the wall as stated in E-1. The machine can be fastened to the floor
using parabolts through the two holes in the bottom of the machine frame.
Check each time before starting that all protection devices are correctly fitted.
Fitting of the Ta le Extension and fences
(the drawing shows the right side, the same procedure is used on the left side).
Before fitting, the ends of the table e tension (13) and the table (7) must be cleaned thoroughly.
Special attention must be paid to the pin and screw holes, as the smallest amount of dirt will prevent
the correct alignment.
After cleaning, the table e tension (13) is pressed against the table so that the pins placed in the
table e tension are inserted in the pin holes in the table. The included bolt is now inserted into the
hole and fastened with a standard spanner.
The fence (8) is fitted on the table e tension (location pins are fitted in the table e tension). It is
secured with Allen screws.
Assembly Instructions F-1
Inhaltsverzeichnis
Andere Hoffmann Industrieanlagen Handbücher
Hoffmann
Hoffmann GARANT VG Basic Bedienungsanleitung
Hoffmann
Hoffmann eXess Bedienungsanleitung
Hoffmann
Hoffmann MORSO NFXL Bedienungsanleitung
Hoffmann
Hoffmann X-10 Bedienungsanleitung
Hoffmann
Hoffmann Garant Bedienungsanleitung
Hoffmann
Hoffmann GARANT HiPo Clamp 125 Bedienungsanleitung
Hoffmann
Hoffmann 10585 Bedienungsanleitung
Hoffmann
Hoffmann FX Series Bedienungsanleitung
Hoffmann
Hoffmann MU2 Bedienungsanleitung
