Holis JSE04-B02-OI01 Bedienungsanleitung
Figure 3: Micro SD card slot and reset button (continued)
Note: Remove the two screws on the camera cover (1) (Figure 3) to
access the buttons. Securely attach the cover when finished.
Table 3: Micro SD card slot and reset button descriptions
Number
Camera button description
1
Camera button cover
2
Micro SD Card Slot
3
Reset button (Hold for more than 3 seconds)
Quick reference
Default IP: 192.168.1.168 (DHCP enabled).
Default Username / Password: admin / admin
Power: 12VDC or PoE 48VDC
Use Internet Explorer 11 web browser.
Mounting the camera to a wall or ceiling
Ensure that the wall or ceiling is strong enough to withstand three times
the weight of the camera.
1. Place the mounting template on the surface that you want to attach
the camera.
2. On the surface drill four Ø 4.6mm holes and cut out a cable hole as
per the markings identified on the mounting template.
3. Securely place the four screw anchors into the four holes.
4. Place the camera cable through the cable hole on the mounting
surface.
OR
Use the cable side entry hole slot (5) (Figure 1) on the camera
base.
5. Note: If you are not using the cable side entry slot ensure that the
cable side entry plug is inserted into the slot on the camera base.
Security
Quick Start Guide
(8200-1994-03_C0)
Tyco Holis JSE Economical 4MP Bullet Camera
(Product Code: JSE04-B02-OI01)
In the box
1 x Camera
1 x Quick Start Guide
4 x PA 4x25mm tapping screws
1 x PWM 3x5mm machine screw
1 x Mounting template
1 x Silicone plug
4 x 6x25mm Plastic screw anchors
Installation tools
Screwdriver
Drill
Figure 1: Camera parts
Figure 1
Table 1: Camera part descriptions
Number
Camera part description
1
Camera lens
2
Sun shield cover
3
Sun shield cover adjustment thumb-screw
4
Camera base
5
Cable side entry slot
6
Camera fixing ring
7
Camera body (Buttons and SD card slot are located
on the underside of the camera). Note: You need to
remove the cover to access them.
Figure 2: Cable connections
Figure 2
Table 2: Cable connection descriptions
Number
Cable connection description
1
Ethernet Connector and also supports PoE
2
Power Connector (12V DC @ 1A)
Figure 3: Micro SD card slot and reset button
Figure 3
Mounting the camera to a wall or ceiling (continued)
6. Hold the camera base (4) (Figure 1) up to the mounting template
and align the four holes on the camera base with the four holes on
the mounting surface.
7. Insert the four screws into the four holes on the camera base and
securely attach the camera to the mounting surface.
Note: The camera must be connected to earth ground.
8. Attach a ring-type terminal to the end of the ground wire (2) (Figure
4) (not provided). Insert the machine screw through the ring
terminal and attach to the camera (1) (Figure 4).
Figure 4: Earth wire connection
Figure 4
Security
Mounting the camera to a wall or ceiling (continued)
9. To power up the camera:
Connect a 12V DC power supply to the power connector on
the camera cable.
OR
Connect a shielded PoE cable to the ethernet / PoE slot on the
camera cable.
Adjusting the sun shield
1. Loosen the thumb-screw (3) (Figure 1) to move the sun shield
cover forward and backward over the camera body (7) (Figure 1).
Note: You must securely lock the thumb screw to ensure that the
sun shield cover holds the modified position.
Figure 5: Pan, tilt and rotate screws
Figure 5
Warnings
If the product does not work properly, please contact your dealer
or the nearest service centre. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance.)
In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the
product is mounted on wall or ceiling, the device shall be firmly
fixed.
Do not allow water or liquid intrusion into the camera.
Do not use camera beyond specified voltage range.
Do not drop the camera or subject it to physical shock.
Avoid touching the camera lens.
If cleaning is necessary, please use clean cloth to wipe it gently.
Do not aim the camera at the sun or extra bright place.
Do not place the camera in extremely hot, cold (the operating
temperature shall be -30˚C~60˚C), dusty or damp locations, and
do not expose it to high electromagnetic radiation.
To avoid heat accumulation, good ventilation is required for
operating environment.
© 2021 Johnson Controls. All rights reserved.
JOHNSON CONTROLS, TYCO, and HOLIS are trademarks and/or
registered trademarks. Unauthorized use is strictly prohibited.
Andere Holis Sicherheitskamera Handbücher
