Honeywell XPO Series Bedienungsanleitung



XPOTM

Ultra Low NOx Indirect Burner

超低排放氮氧化物間接燃燒器



 Low temperature burner for use with clean fuel gases

使用清潔燃氣的低溫燃燒器



 Single digit NOx emissions at 30% excess air

在 30%的過剩空氣下，氮氧化物排放只有個位數



 High efficiency with low excess air requirements

低過剩空氣要求下，高效率



 Capacities up to 2250KW.

高達 2250KW 的燃燒效率



 For use in indirect fired solution backed heaters

用作間接液體加熱



1 08092018



I． Product description 產品介紹



MAXON XPO™ burners are low temperature burners for use in

liquid backed applications, including:

麥克森 XPO™低溫燃燒器，適用于液體應用，包含：

 Water back heater 回水鍋爐

 Fire tube boiler 火管鍋爐

 Thermal oil heater 導熱油爐

 Direct contact water heater 直接接觸熱水加熱器

 Solution heating/tanks 液體加熱器/ 罐

 Snow melter 雪熔爐



XPO™ burners provide high efficiency operation with low

excess air requirements. They are designed for ease of

retrofitting into existing liquid backed applications. XPO™燃

燒器對過剩空氣的要求低，但運行效率高。

其設計旨在更方便地對現有的液體加熱應用進行改

造。



The packaged XPO™ burners are intergrated with flame

supervision, safety interlock and flow control function, with user

freiendly interface for operator.The Standard configuration include:



1: Intergrated Double safety shut-off valve with pressure regulating

funciton.



2: SLATE burner control unit with electrical parral actuator with air

dampler+ gas BV.



3: UV sensor



4: Gas high/low pressure switch+ pressure switch for valve tightness

test+ air pressure switch.



5:package blower or separate blower to be installed on-site( depends on

burner model)



Note:

It’s customer’s responsbility to install the gas filter and manual shut-off

valve upstream of the gas inlet.



Layout 1: remote blower



Layout 2: back installed control panel



Layout 3 Side installed control panel



Layout 4 Packaged control panel



Layout 5 Packaged control panel

UV breakaway type



2 08092018

3 08092018



II． Available XPO™ ultra low NOx burner sizes XPO™超低氮氧化物燃燒器的可選型號



Typical Burner Data 燃燒器數據

燃料：天然氣，LHV=8500 kcal/Nm3, 壓力一個大氣壓，溫度 0 °C 空氣：壓力一個大氣壓，溫度 15 °C



XPO 1PB XPO 2PB XPO 3PB XPO 4PB



XPO 5PB XPO 5PB+ XPO 3PAK XPO 5PAK

Based on 18% excess air 基於 18% 的過剩空氣測得的結果

燃燒器最大功率 KW 400 525 960 1260 1700 2000 960 1700

調節比 4.:1 4:1 4:1 4:1 4:1 4:1 4:1 4:1

額定助燃風量 m3/hr 625 850 1260 1870 2340 2920 1260 2340

助燃風機功率 KW 1.1 2.2 4 4 5.5 11 4 5.5

助燃風壓力 mbar 30 28 40 40 40 56 40 40

燃燒管外徑 mm 

152 152 152 203



203 203 152 203

鍋爐燃燒管內徑 mm 

355-457 406-560 457-610 560-812



560-864 560-914 457-610 560-864

燃氣壓力 mbar 

100-350 100-350 100-350 100-350



150-350 200-350 100-350 150-350

爐膛背壓 mbar 適用鍋爐（熱水或蒸汽) 噸/小時

0 0.5 W/S 0.5 W/S 1.0 W/S 1.5 W/S 2 W/S 2.5 W/S 1.0 W/S 2 W/S



5 0.5 W/ 0.45 S 0.5 W/S 1.0 W/S 1.5 W/1.47 S 

2 W/S 2.5 W/ 2.4 S 1.0 W/S 2 W/S



7.5



0.5 W 0.5 W/S 1.0 W/S 1.5W/1.42 S 2 W/ 1.9 S 2.5W/ 2.3S 1.0 W/S 2 W/ 1.9 S



0.47 W 0.5 W/0.48 S 1.0 W/S 1.5 W/1.35 S 2W /1.84 S 2.5W/ 2.3S 1.0 W/S 2W/ 1.84 S

注意：

1. 燃燒器最大功率受燃料及爐膛背壓的影響。

2. W 表示熱水鍋爐，S 表示蒸汽鍋爐。

3. 夏季（氣溫 30 °C-35 °C）測試功率會減少 3%

4 08092018



III． Dimensions for installaiton 安裝尺寸



XPO 1,2&3PB XPO 4&5PB



XPO 3&5PAK

5 08092018



Burner

Size

XPO

1PB

XPO

2PB

XPO

3PB

4PB

XPO

5PB

XPO

5PB+

XPO 3

PAK

XPO 5

PAK

A 1145 1145 1145 1096 1096 1096 1147 1096

B 848 838 810 756 736 736 813.6 736



C The dimension will be different based on layout. Ask layout drawing from HTS

sales.

高度和長度根據佈置的不同會有變化，請參照 Honeywell 單獨提供的組裝

圖尺寸



E 45° 45° 45° 30° 30° 30° 399.6 521

F 457 457 457 711 711 711 321 410

G 420 420 420 641 641 641 281 360

H 160 160 160 209 209 209 160.1 209

I 23 23 23 23 23 23 220.2 288

J 16 16 16 16 16 23 17.5 17.5

K*note 159 159 159 216 216 216 159.1 216



Note: The flange for XPO1,2,3 and 4,5 are different. Both on bolts position and quantity, please see the drawing.

6 08092018



IV． Burner mounting instructions 燃燒器安裝指導



FLANGE THE BURNER TO THE INSTALLATION



Bolt the burner to the installation’s burner mounting flange. Use proper gasketing. Tighten the flange bolting with correct

torque. Retighten all bolts after first firing and regularly after commissioning.



All non-liquid cooled surfaces must be insulated as shown in burner mounting diagram. Area(s) between fire tube wall and

outside of burner blast tube must be completely filled with insulation as shown below. Customer-supplied scanner tube must

not extend beyond the blast tube insulation.

*Recommended insulation properties: minimum density of 16 kg/m3 or greater with minimum thermal conductivity of 12

W/m.K at 980°C.



1) XPO™ burner XPO™燃燒器

2) Mounting flange 固定法蘭

3) Unit wall 單元牆

4) Liquid solution 液體溶液

5) Fire tube 煙管

6) Burner blast tube 燃燒器排氣管

7) Non-cooled fire tube wall 非冷卻煙管壁

8) Customer-supplied insulation* 客戶提供的隔熱材料*

*All non-liquid cooled surfaces must be insulated as shown above.

*所有非液體冷卻面必須按如圖所示方式進行隔熱



1) Blast tube

2) Liquid solution

3) Fire tube

4) 152 mm gap required

from insulation to

slots

5) Customer-supplied

scanner tube

6) Customer-supplied

insulation (minimum

Correct installation

Blast tube is completely insulated beyond point

where fire tube is solution backed. Minimum of 3”

insulation into liquid.



Incorrect application/installation

Blast tube cannot be completely insulated due to

protrusion length of fire tube out of solution.



152 mm depth from

blast tube flange) *



4 1 1



3 5 3

2 2

7 08092018



V． SAFETY 安全



Sufficientsafeaccessshouldbepresenttoallowworkontherelevant components. This manual is

compiledtoalevelwhichassumesthatpersonnelemployedontheoperatingandmaintenanceworkare

familiarwiththeprinciplesandtechniquesusedinthetypeofequipmentdescribed,andareawareofthe

hazardsassociatedwiththeequipmentanditsworkingenvironment. Theinformationgivenisintended

tosupportoperatingandmaintenanceproceduresandshouldnotbetakenasacontractualspecification.



提供充足的空間以保證對相關元件進行安全操作。此手冊只適用於熟悉所描述設備的操作方法和技術並具有

相關

知識的操作和維修員工，並且要意識到設備誤操作可能帶來的相關的危害。本手冊所提供的資訊用於支

持操作

和維修步驟，不可作為合同條件。



Inquiresrelatingtothismanualshouldbemadetotheaddressonthecoversheet.



與此手冊內容有關的問題請參照首頁上的位址進行詢問。



Allwork andoperationoftheplantshouldbe carriedout bytrained/qualifiedoperators,tradesmenor

engineers.



車間的所有工作和操作必須由培訓過或有資格的操作員，技術工人或工程師完成。



Beforeundertakingmaintenanceworkonanyitemoftheequipmentitmustbemadesafe.



在對設備任何專案進行維修工作前，必須保證設備處於安全狀態。





Fuelsupplyshouldbemanuallyisolatedandfuelisolatingvalvelockedinthe“OFF”position.

燃料供應必須手動隔離，燃料隔離閥鎖定在“關閉”位置。





Anypneumaticcomponenttobeworkedonshouldbepneumaticallyisolatedanddrainedofany

pressure,anddrainsleftopenwithcautionnoticesifnecessary.

要維修的任何氣動元件必須隔離氣源和排出所有剩餘空氣，必要時打開排放口，在排放口打開時要

有

警示標誌





Anyelectricalcomponentstobeworkedonshouldbeelectricallyisolatedatthecontrolpanel,the

fusesremovedandtheisolatorlockedinthe“OFF”position.

要維修的任何電氣元件必須在控制台上切斷電源，移除保險絲，開關鎖定在“關斷”位置。

8 08092018



VI． INSTALLATION 安裝



ItistheresponsibilityoftheCustomertoinstallalloftheequipment.



客戶對設備的安裝負責。



Piping weight should be independently supported. Do not use the burner as a piping support or hang

weight from the burner’s flange connections.

管路必須單獨設置支撐，不能把燃燒器的法蘭盤當作管

路支撐或者在法蘭盤處懸掛重物。



Any damage caused by the improper installation, handling or improper use of the equipment is the

responsibilityoftheCustomer. Priortoinstallationoftheequipmentthefollowingissuggested.



由於安裝不當，處理和使用不當對設備造成的損壞應由客戶負責。因此，設備安裝前應遵循以下建議：



1. Inspectallcomponentsuponarrival. Insurequalityandquantityofcomponentsiscorrect. Reportany

missingordamagedequipmenttoEclipseCombustion(Suzhou)immediately.



設備到達後，檢查所有部件，確保品質和數量正確。如有丟失或損壞部件，立即通知天時公司。



2. Duringinstallationinsurethefollowing:



安裝過程中確保以下要求：



 Allvalvehandlescanrotatetofullopenorfullcloseposition.

所有閥門手柄能夠開關自如。



 Allelementsarepipedintheproperflowdirection.

所有部件安裝方向正確。



 Interconnectingpipingshouldbeinstalledinsuchamannerthatunduestresswillnotbeimposed

ontheMainGasTrain.

連接管道不應對燃氣盤產生應力。



 Insure the piping system is pressure tested and blown clean before final connection to any

equipment.

確保管路系統在連接到任何設備之前，已進行試壓並吹掃乾淨。



 Whenpressuretestinginsureallpressuregaugesandareisolated,highpressurewilldamagethe

gauges.Keepallpressuregaugescloseduntilstart‐uptoinsuretheyarenotdamaged.

在試壓時，關閉所有壓力錶的隔離閥，以防高壓損壞表頭。保證所有壓力錶隔離閥關閉，直到啟動前.



 EclipseCombustion(Suzhou)willnotberesponsibleforanydamagecausedbyexcessivepressure.

蘇州天時燃燒公司不對壓力過高對設備產生的損壞負責。



 Insureallwiringischeckedpriortoenergizingthesystem.Damagecausedbyimproperwiringis

nottheresponsibilityofEclipsecombustion(Suzhou).

在系統上電之前，檢查所有接線。蘇州天時燃燒不對由於接線問題產生的損壞負責。

9 08092018



VII． OPERATION AND MAINTENANCE 運行和維護



Eclipseburnerequipmentisdesignedtominimizemaintenance.



天時燃燒設備設計的主要目的是把維修減少到最小化。



1. Interlocks

安全聯鎖裝置



a. With burner and process operating normally check all control and safety interlocksfor

correctoperationandsystemreaction.

在燃燒器運行正常的情況下，檢查所有的控制器和安全聯鎖裝置是否正確運作以及系統的反

應正常。



2. OperatingData

運行資料



a. Withburnerandprocessoperatingnormallyandsatisfactorily,optimizeandrecord

operatingrangeparameters,including:

在燃燒器運行正常情況下，完善和記錄以下工作參數：



i. Pressures;壓力

ii. Flows;流量

iii. Temperatures;溫度

iv. Settings;設置

v. Combustionanalysis.燃燒廢氣分析

3. To ensure continuing trouble free operation the following areasshouldbeaddressedatthe

intervalsshown.



為了保證連續無故障運行，以部件見需在顯示的時間間隔中進行週期性的檢查。



INTERVAL時間間隔

1Months



1個月

3Months



3個月

6Months



6個月

12Months



12個月

CheckFlameDetectionSignal



檢查火焰信號

X



CleanSparkPlug



清潔火花塞



X



CleanUVScanner/FlameRod



清潔紫外線探頭/火焰棒



X



10 08092018



CleanFanImpeller



清潔風扇葉輪



X



CleanFanFilterElement（addclean

timesaccordingtoactualsituation）



清潔風扇泡棉(根據實際情況可以增

加清洗次數)



X



GreaseFanMotorBearings(See

componentsectionfordetails)



給風機馬達軸承上潤滑油（詳細參照部

件

部分）





X



CleanBurnerWorkingSurfaces



清潔燃燒器工作表面



X



CompareGasPressureAtBurnerInlet

WithCommissioningData



將燃燒器進氣口處燃氣壓力和調試資料

進

行比較





X



ConfirmCorrectOperationOf

PressureSwitches



確認壓力開關正確運行



X



ReplaceSparkPlug



更換火花塞



X

ReplaceUVScanner/FlameRod



更換紫外線探頭/火焰棒



X

Check&CleanAir&GasPortsInPilot

BurnerCasting



檢查和清潔點火管路燃燒器鑄件上的空

氣

和燃氣口





X

CleanSeatsonPilot&MainGasSafety

Shut‐OffValves



X

Dieses Handbuch passt für folgende Modelle

Andere Honeywell Brenner Handbücher

Honeywell

Honeywell Ecomax Series Handbuch

Honeywell

Honeywell Eclipse ImmersoPak IP005 Bedienungsanleitung

Honeywell

Honeywell MAXON VALUPAK-II Series Bedienungsanleitung

Honeywell

Honeywell C7005A Bedienungsanleitung

Honeywell

Honeywell Hauck MEGASTAR MS-25 Bedienungsanleitung

Honeywell

Honeywell Q345U Bedienungsanleitung

Honeywell

Honeywell Maxon OT FHR Bedienungsanleitung

Honeywell

Honeywell TRADELINE Q314 Bedienungsanleitung

Honeywell

Honeywell Eclipse Winnox WX Series Bedienungsanleitung

Honeywell

Honeywell Eclipse WX0050 Bedienungsanleitung

Honeywell

Honeywell Eclipse ImmersoJet Leitfaden

Honeywell

Honeywell CS8800 Bedienungsanleitung

Honeywell

Honeywell Q179A Bedienungsanleitung

Honeywell

Honeywell Q349A Series Bedienungsanleitung

Honeywell

Honeywell Ecomax 3M Bedienungsanleitung

Honeywell

Honeywell TRADELINE Q314 Bedienungsanleitung

Honeywell

Honeywell Maxon VALUPAK-II Bedienungsanleitung

Honeywell

Honeywell PRO 2000 Series Bedienungsanleitung

Honeywell

Honeywell SmartValve Q3450A Bedienungsanleitung

Honeywell

Honeywell Maxon OXYTHERM FHR Bedienungsanleitung

Beliebte Brenner Handbücher anderer Marken

Riello

Riello RS 28/M Kurzanleitung

True Induction

True Induction TI4B Bedienungsanleitung

Weishaupt

Weishaupt WG20 Series Bedienungsanleitung

Carolina Cooker

Carolina Cooker M116672 Bedienungsanleitung

Riello

Riello RX 500 S/PV Bedienungsanleitung

Unigas

Unigas HTP2000 Bedienungsanleitung

baltur

baltur BT 250 DSG 4T Bedienungsanleitung

muenkel design

muenkel design round burner Bedienungsanleitung

baltur

baltur BT 14 DSGW Bedienungsanleitung

artisan

artisan Art-SB1 Leitfaden

AESYS

AESYS TurboFire II Bedienungsanleitung

Riello

Riello RG1RKD Kurzanleitung

IKEA

IKEA GRILLSKÄR Bedienungsanleitung

RUSTA

RUSTA SAREK Bedienungsanleitung

PROPOINT

PROPOINT 8933657 Bedienungsanleitung

baltur

baltur TBL 1000 ME Referenzhandbuch

Riello Burners

Riello Burners P 200 P/G Kurzanleitung

WLD-TEC

WLD-TEC powerjet Bedienungsanleitung