Honeywell Temaline TKL19 Bedienungsanleitung

Tema1.0_L19_IM_1.0_EN Pagina 1 di 24

TKL19 (RTUL19)

Installation Manual

Page 2 of 24

CONTENTS

1.1 Wall Set Up for the Cable Trays.........................................................3

1.2 Electrical Connections........................................................................4

1.3 LONWORKSData Cables................................................................6

1.4 Mounting the Wall Bracket..................................................................7

1.5 Cable Connections .............................................................................8

1.5.1 LON Cable..............................................................................8

1.5.2 Power Supply Cable +12VDC................................................9

1.5.3 Input Cable 1 – Door Contact...............................................10

1.5.4 Input Cable 2 - Button ..........................................................11

1.5.5 Output Cable Relay 1- Door Open ....................................... 12

1.5.6 Output Cable Relay 2 – Signal Light .................................... 15

1.6 Mounting the Device on the Wall Bracket.........................................17

1.7 Identification Using the Service Pin.................................................. 18

1.8 Identification Using the Neuron ID....................................................19

2.1 TemaKey TKL19 (RTU-L19 code 1500154xx)...................................20

2.1.1 Supplied Parts......................................................................21

2.1.2 Optional Parts.......................................................................21

2.2 Recycling..........................................................................................22

Page 3 of 24

The cables must:

1) Protrude from the wall.

2) Come out at 120cm from ground (see Figure 1) (advised).

cable tray

cables

120cm

Floor

Figure 1: Wall Set Up for the Cable Trays

Version: 1.0 EN

Page 4 of 24

The RTU is powered at low voltage (12VDC 160mA), preferably using a

power supply module with battery backup (RTU-Qxx), or using an ordinary

power supply having the same characteristics. The power cables must be

dimensioned as indicated in the table below. The maximum allowable voltage

drop on the power cable is 1V.

• Cable length(m) = 1V / (I[A] load x 2 x (res [Ohm/km] /1000))

Cabl e Type Ext ensi on [ m] based on l oad

AWG mm2 ohm/ Km 160 [ mA] 320 [ mA]

12 3. 3 5. 7 548 274

14 2 8. 8 355 178

16 1. 3 14 223 112

18 0. 9 21 149 74

20 0. 6 34 92 46

22 0. 35 52 60 30

24 0. 2 85 37 18

The device is equipped with 2 non-removable cables of 2m length:

• Two-pole, twisted, unpolarized cable dedicated to the LON line

connection

- LON a 0,325 mm2white

- LON b 0,325 mm2orange

• Ten-pole cable, providing the following signals:

- +12VDC 0,34 mm2red

- GND 0,34 mm2black

- INPUT 1 + 0,22 mm2green / white

- INPUT 2 + 0,22 mm2gray / green

- RELAY 2 contact C 0,22 mm2brown

- RELAY 2 contact NC 0,22 mm2white

- RELAY 2 contact NO 0,22 mm2blue

- RELAY 1 contact C 0,56 mm2green

- RELAY 1 contact NC 0,56 mm2yellow

- RELAY 1 contact NO 0,56 mm2gray

The signals must be connected using a shunt box with IP protection level

in conformance with the type of environment in which it is to be used:

- IP55 for moist environments

- Recessed box or IP31 at least for inside installations

The shunt box must be positioned within the perimeter controlled by the

access control system.

Page 5 of 24

If necessary, the repeater relays must be inserted inside the box for

electrical locking commands and the signal light.

Figure 2: Position and dimensions of the non-removable cables

4,20 cm

2 meters

Shunt Box

Cable +12VDC

Cable LON

Cable IN 1

Cable IN 2

Cable OUT 1

Cable OUT 2

RTUL19

Figure 3: Shunt Box

15,60 cm

7,20 cm

6,10 cm

2 metri

8,00 cm

2-pole LON

cable

4 mm diamete

10 pole

cable

8.6mm

diamete

Page 6 of 24

S



• The LONWORKS1data cables must be double twisted-pair cables

• In a free topology configuration, the overall length of the sections must not

exceed 500m

• In a bus configuration, the overall length of the sections must not exceed

2700m

• In the free topology configuration, the 50ohm terminator must be enabled

by inserting the appropriate jumper into the FTT10A plug-in on the CTU-

PLG06 board inside the TemaServer

• In a bus configuration, two terminators must be inserted at the two ends of

the bus (resistance of 100ohm 1% ½W)

• The LONWORKS1data cables must be dimensioned according to the

indications in Table 1

Cable Type Extension [m] based on cable capacitance

AWG mm2Ohm/Km 50nF/Km 100nF/K

200nF/K

500nF/K

1uF/Km

12 3.3 5.7 2676 1892 1338 846 598

14 2 8.8 2153 1523 1077 681 482

16 1.3 14 1707 1207 854 540 382

18 0.9 21 1394 986 697 441 312

20 0.6 34 1096 775 548 346 245

22 0.35 52 886 626 443 280 198

24 0.2 85 693 490 346 219 155

Table 1: Length/Capacitance of LONWORKS



1 Cables

• The FTT10A Echelonv1.2 User’s Guide suggests using the cables as

indicated in Table 2.

Make and Model AW

Bus

Connection

Max Length

total [m]

Free Topology

Connection Node-

to-Node Max

Length [m]

Free Topology -

Connection

Max Length total

[m]

Belden 85102 16 2700 500 500

Belden 8471 16 2700 400 500

Level IV (twisted pair,

solid, unshielded)

22 1400 400 500

JY (St) 2x2x0,8 (4

solid wires, spiral-

twisted, shielded)

20 900 320 500

TIA Cat5 / 900 250 450

Table 2: Suggested LONWORKS



Cables

1LONWORKS®is a trademark of the Echelon Corporation

Page 7 of 24

Mount the bracket onto the wall as follows:

1. Placing the bracket against the wall to indicate the proper positions of the

holes, make the holes for the two bolts that will go into the wall to hold the

bracket (the bolts are included in the installation kit)

2. Make sure that the cable tray bathces with the hole for the passage of the

cables

3. Screw in the bolts.

Figure 4: Wall Bracket: Front View and Side View

Hole for Cables

Hole for inserting bolt and

screw to press against the

anti-removal/anti-open

tamper

Holes for wall

mounting

Page 8 of 24

1.5.1 LON Cable

Figure 5: LON (1) Cable Connection

6,10 cm

2 meters

LON A

LON B

Note: connection

not polarized

Page 9 of 24

1.5.2 Power Supply Cable +12VDC

6,10 cm

2 meters

12VDC (red)

GND (black)

Figure 6: Power Supply Connection

Page 10 of 24

1.5.3 Input Cable 1 – Door Contact

The balanced input 1 is dedicated to door status control; the balancing

resistances must be positioned near the clean sensor contact.

White

Yellow

magnetic door contact

NC CONTACT

Figure 7: Connection for Balanced Input 1 – Door Contact

GND (black)

IN1 (green / white)

Inhaltsverzeichnis

Andere Honeywell Kartenleser Handbücher

Honeywell

Honeywell 1026FF02F9 Bedienungsanleitung

Honeywell

Honeywell IF2B Bedienungsanleitung

Honeywell

Honeywell IdentIPoint Bedienungsanleitung

Honeywell

Honeywell Dolphin 9700-MSCR Bedienungsanleitung

Honeywell

Honeywell OmniTek OmniProx OP10 Series Bedienungsanleitung

Honeywell

Honeywell Accentic Gebrauchsanweisung

Honeywell

Honeywell luminAXS Series Gebrauchsanweisung

Honeywell

Honeywell IF2 Bedienungsanleitung

Honeywell

Honeywell OmniClass OM15 Bedienungsanleitung

Honeywell

Honeywell OmniProx OP-95 Bedienungsanleitung

Honeywell

Honeywell IF2 Bedienungsanleitung

Honeywell

Honeywell SPR-S8EZS Bedienungsanleitung

Honeywell

Honeywell IH25-0 Bedienungsanleitung

Honeywell

Honeywell Dolphin CN80G Bedienungsanleitung

Honeywell

Honeywell Accentic 026423 Bedienungsanleitung

Beliebte Kartenleser Handbücher anderer Marken

Lindy

Lindy 43185 Bedienungsanleitung

Lindy

Lindy 43185 Bedienungsanleitung

ViziT

ViziT RD-4F Bedienungsanleitung

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Bedienungsanleitung

AVID ID

AVID ID AVID1043 Bedienungsanleitung

Conrad

Conrad PCMCIA Bedienungsanleitung

Rosslare

Rosslare DR-6255 Bedienungsanleitung

Lindy

Lindy 51541 Bedienungsanleitung

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Bedienungsanleitung

Johnson Controls

Johnson Controls Kantech tyco ioSmart Bedienungsanleitung

ACS

ACS ACR122L Bedienungsanleitung

Secukey

Secukey S2-MF Bedienungsanleitung

Elecom

Elecom MR-SMC07 series Bedienungsanleitung

Alien

Alien ALR-9800 Bedienungsanleitung

ACS

ACS ACR310 Bedienungsanleitung

Datamars

Datamars R-IN1300 MID Bedienungsanleitung

Alarm Lock

Alarm Lock AL-PRE2 Bedienungsanleitung

xpr

xpr B100PROX-AH Benutzerhandbuch