Honeywell CentraLine CLIOL822A Bedienungsanleitung

LonWorks Bus I/O Modules Product Data

GENERAL

The CentraLine LONWORKS Bus I/O Modules communicate

via the LONWORKS Bus.

These pluggable CentraLine LONWORKS Bus I/O modules

consist of a terminal socket and a removable electronic

module, allowing the socket to be mounted and wired before

the electronic module is installed. All such electronic modules

can be swapped out without disrupting the power and bus

connections: Simply unplug the “old” and insert the “new”

module.

WARNING

Risk of electric shock or equipment damage!

► Do not touch any live parts in the cabinet.

► Disconnect the power supply before you start to install

the control system. More than one disconnect switch may

be required to de-energize the system.

► Do not reconnect the power supply until you have

completed the installation.

► Unused terminals must be closed (by completely

screwing in the terminal screws), thus preventing the

accidental touching of “live” parts.

Software updates, configuration, and commissioning are all

done automatically by the controller for all LONWORKS Bus I/O

Modules.

The LONWORKS Bus I/O Modules may be used with any CPU

supporting LONWORKS Bus communication (e.g., the LION,

EAGLE, etc.).

FEATURES

 Plug-and-play functionality for easy maintenance.

 Pluggable LONWORKS Bus I/O modules can be exchanged

without rewiring. Further, the separate installation of

terminal sockets and electronic modules lower risk of

damage and theft in the construction phase.

 Fast wiring with state-of-the-art push-in terminals (screw-

type terminals also available) and bridge connectors.

 Wide range of sensors supported (NTC20kΩ, NTC10kΩ,

PT1000-1/-2, Johnson A99 PTC, NI1000TK5000, PT3000,

Balco500, 0/2…10 V, 0/4…20 mA).

 Binary input LEDs of the CentraLine LONWORKS Bus I/O

Modules can be configured for status display (off / yellow)

or alarm display (green / red) per channel.

 Configurable safety position for outputs, in case of loss of

communication with the controller.

 Max. wiring flexibility due to optional accessories like

auxiliary terminals and cross-connectors.

 Can be mounted in small installation housings

 Flexible mix of LONWORKS Bus I/O modules covering all

your application requirements.

LONWORKS BUS I/O MODULES – PRODUCT DATA

EN0Z-0980GE51 R0119 2

OVERVIEW

LonWorks

BUS MODULES

pluggable

ANALOG OUTPUT

pluggable

ANALOG INPUT

pluggable

BINARY INPUT

XS821-22

XSU821-22

CONTROLLER

S823

SU823

S824-25

SU824-25

pluggable

RELAY OUTPUT

LonWorks Bus

CLIOL821A

CLIOLR822A

CLIOL822A CLIOL823A

CLIOLR824A

CLIOL824A

Fig. 1. Overview of CentraLine LonWorks Bus I/O Modules

Table 1. Overview of CentraLine LonWorks Bus I/O Modules

order number description

LonWorks Bus I/O Modules

CLIOL821A LONWORKS Bus Bus Analog Input Module (with 8 analog inputs)

CLIOL822A LONWORKS Bus Bus Analog Output Module (with 8 analog outputs)

CLIOLR822A LONWORKS Bus Bus Analog Output Module (with 8 analog outputs and manual overrides)

CLIOL823A LONWORKS Bus Bus Binary Input Module (with 12 binary inputs)

CLIOL824A LONWORKS Bus Bus Relay Output Module (with 6 relay outputs)

CLIOLR824A LONWORKS Bus Bus Relay Output Module (with 6 relay outputs and manual overrides)

Terminal Sockets

XS821-22 Push-in terminal socket for AI/AO modules (incl. bridge connector, swivel label)

XSU821-22 Screw-type terminal socket for AI/AO modules (incl. bridge connector, swivel label)

XS823 Push-in terminal socket for BI modules (incl. bridge connector, swivel label)

XSU823 Screw-type terminal socket for BI modules (incl. bridge connector, swivel label)

XS824-25 Push-in terminal socket for relay/floating output modules (incl. bridge connector, cross connector, swivel label)

XSU824-25 Screw-type terminal socket for relay/floating output modules (incl. bridge connector, cross connector, swivel label)

Table 2. Overview of auxiliary parts and spare parts

order number description

XS814

Ten Auxiliary Terminal Blocks (for distribution of signals/power). Each terminal block includes two

groups with seven internally-connected push-in terminals.

XS815

20 Cross-Connectors for connection of six relay commons. One Cross-Connector is included in the

Terminal Socket package.

XS816

10 Bridge Connectors. One Bridge Connector is included in the Terminal Socket package.

XAL10

10 Swivel Labels Holders (for attaching the application-specific label printed with CARE / COACH AX /

COACH NX). One Swivel Label Holder is included in each Terminal Socket package. NOTE: Phased

out.

NOTE: The inputs and outputs of all CentraLine analog and binary I/O modules are protected against short circuit,

24 VAC +20%, and 40 VDC.

In the case of the relay outputs of other CentraLine I/O modules (i.e., relay output modules, floating output

modules, and mixed I/O modules), appropriate fusing must be provided to ensure that permissible load currents

are not exceeded. See also sub-section "Features" in section "Relay Output Modules" on pg. 14.

LONWORKS BUS I/O MODULES – PRODUCT DATA

EN0Z-0980GE51 R0119

Table 3. Pluggable LonWorks Bus I/O Module specifications

Module Analog Input Analog Output Binary Input Relay Output

CLIOL821A CLIOL822A, CLIOLR822A CLIOL823A CLIOL824A, CLIOLR824A

no. of I/Os 8 analog inputs 8 analog outputs 12 binary inputs

requiring a gold contact

or open collector

6 relay outputs

characteristics Linear Graph, 0...10 VDC with pull-

up, 0(2)…10 VDC without pull-up

NTC20kΩ (-50…+150 °C, default)

NTC10kΩ (-30…+100 °C)

PT1000-1 (-50…150 °C)

PT1000-2 (0…400 °C)

Johnson A99 PTC (-40…+120 °C)

NI1000TK5000 (-30…+130 °C)

PT3000 (-50…150 °C)

BALCO500 (-30…120 °C)

Also configurable as:

binary inputs

 Linear graph (0…10 V with pull-up)

Features:

 16-bit resolution

 configurable offset per input

 auxiliary voltage: 10 VDC, Imax =

5 mA

0…11 VDC /  1 mA

Also configurable as: floating

outputs or binary outputs (0 V

/ 10 V)

Features:

 8-bit resolution (default)

 Safety position (remain, 0%,

50%, 100%)

 red LED per output

 light intensity follows output

level in auto

Version with manual

override (R):

 1 potentiometer per output

 auto feedback signal (mode

+ value)

 blinking in manual override

position

static binary input,

(default: dry contact)

Also configurable as:

totalizers (20 Hz)

Features:

 1 LED per input

 Color mode can be

set per input to

OFF/yellow or

green/red using

CARE / COACH AX /

COACH NX

 ON: < 1.6 kΩ to GND

or < 2.5 V to GND,

OFF: > 90 kΩ to

GND or > 4 V to

GND

relay outputs (default)

Features:

 Changeover relays

 Voltage: 19…250 VAC,

1…29 VDC, P>50 mW

 max. total current: 12 A

 current per relay: N.O.: 4(4) A

(AC) or 4(1) A (DC),

N.C.: 2(1) A (AC) or 4(1) A

(DC)

 Safety position (remain, 0%,

100%)

 yellow LED per output

Version with manual override

(R):

 1 switch per output

 auto feedback signal (mode +

value)

 blinking in manual override

position

Manual Overrides as per EN ISO 16484-2:2004

The manual override switches and potentiometers of the output modules support direct operation as per EN ISO 16484-

2:2004, section 5.4.3 "Local Priority Override/Indicating Units."

Specifically, the positions of the manual override switches and potentiometers directly control the outputs – independently

of the controller and HMI. When a manual override switch or potentiometer is not in its default position ("auto"), the

corresponding output LED will blink continuously, and the output module will send a feedback signal with the status

"manual override" and the given override position to the controller (which will then also store this information in its alarm

memory).

NOTE: When updating the firmware of output modules, their outputs are turned OFF – regardless of the position of their

manual override switches and/or potentiometers.

LONWORKS BUS I/O MODULES – PRODUCT DATA

EN0Z-0980GE51 R0119 4

GENERAL FEATURES

PRESS

123

Honeywell

AUTO

AAA

100

S1 S2

71COM a

72COM b

7324V

7424V 0

14 4424 5434 64 25

11 31

6363

12345678

Honeywell

AUTO

AAAAAAAA

100

S1 S2

GND GND

AI/AOV

AUX

10 11 12 13 14 15 16 17 18 25 26

22 1 2 345678

123456

Honeywell

--1

--0

--AUTO

S1 S2

14 4424 5434 64 25

11 31

6363

12345678

Honeywell

GND GND

AI/AOV

AUX

10 11 12 13 14 15 16 17 18 25 26

22 1 2 345678

GND

13 14 15 16 17 18 19 20 21 22 23 24 25 26

12345678910

11 12

1 2 34 5 6 7 8 9 10 11 12

Honeywell

S1 S2

71 COM a

72COM b

7324V

7424V 0

PRESS

1:ABCDFERTAQWESDERT1

2:ABCDFERTAQWESDERT2

3:ABCDFERTAQWESDERT3

4:ABCDFERTAQWESDERT4

5:ABCDFERTAQWESDERT5

6:ABCDFERTAQWESDERT6

7:ABCDFERTAQWESDERT7

8:ABCDFERTAQWESDERT8

342

6 7

71COM a

72COM b

7324V

7424V 0

Fig. 2. LonWorks Bus I/O Modules on DIN rails

Legend

1 Controller (e.g., LION, EAGLE, HAWK, etc.)

2 Cable (power, LONWORKS) connection from controller to

LONWORKS Bus I/O Modules

3 Swivel label holder

4 Cable connection between LONWORKS Bus I/O Modules

on separate DIN rails

5 Bridge connectors between LONWORKS Bus I/O Modules

on same DIN rail

6 Stopper (from 3rd-party supplier)

7 Auxiliary terminal packages

LEDs

Each CentraLine LONWORKS Bus I/O Module is equipped

with:

 one green power LED

 one yellow service LED

Overvoltage Protection

The inputs and outputs of all CentraLine analog and binary

I/O modules are protected against short circuit, 24 VAC

+20%, and 40 VDC.

In the case of the relay outputs of other CentraLine I/O

modules (i.e., relay output modules, floating output modules,

and mixed I/O modules), appropriate fusing must be provided

to ensure that permissible load currents are not exceeded.

See also sub-section "Features" in section "Relay Output

Modules" on pg. 14.

Service LED

Each LONWORKS Bus I/O Module is equipped with a yellow

service LED (status: yellow/OFF) for easy diagnosis of

failures.

LonWorks Service Button

Each LONWORKS Bus I/O Module is equipped with a

LONWORKS service button.

Microprocessors

Each LONWORKS I/O Module is equipped with an FTT-10A

transceiver (link power-compatible) and can thus be used with

any LONWORKS controller.

In addition to the main microprocessor, the LONWORKS Bus

I/O Modules also have their own Neuron chip (3120).

System Constraints

Table 4. System constraints

Max. no. of I/O modules (any

combination) per controller

depends upon

controller type

Max. no. of I/O modules per row 10

Max. current (F1) 4 A

Max. current (F2) 12 A

Max. current (F3) 12 A

Max. row length 3 m

Max. distance between rows 40 m

Min. cross-section of GND

(terminal 9) (protected by F2) 1.5 mm2

LONWORKS BUS I/O MODULES – PRODUCT DATA

EN0Z-0980GE51 R0119

Analog Input Module

Fig. 3. CLIOL821A LonWorks Bus AI Module (shown with

terminal socket)

Legend

1 LONWORKS service button S1

2 Service LED

3 Power LED

NOTE: The hex switch S2 (located next to the LONWORKS

service S1) has no function in combination with a

LONWORKS Bus I/O module. It is used with Panel

Bus I/O modules, only.

The CentraLine LONWORKS Bus Analog Input Module, with 8

analog inputs, is installed with the XS821-22 or XSU821-22

Terminal Socket.

24.9 kOHM

RTD

10 VDC

GND

Fig. 4. Analog input low impedance (input circuit for

PT1000, Johnson A99 PTC, Balco500, PT3000,

NI1000TK5000, slow binary input)

199.9 kOHM

GND

Fig. 5. Analog input high impedance (input circuit for

voltage input for active sensors)

199.9 kOHM

(8.9 VDC IF

CONNECTION

INTERRUPTED)

GND

24.9 kOHM

10 VDC

Fig. 6. Analog input impedance setpoint (input circuit for

NTC10kΩ, NTC20kΩ, wall module setpoint)

71 75

72 76

73 77

AUX

GND GND GND GND GND GND GND GND GND GND

AUX

AI1 AI2 AI3 AI4 AI5 AI6 AI7 AI8

18 25 26

COM

ACOM

COM

BCOM

V~ 24

V~0 24

Fig. 7. CentraLine LonWorks Bus Analog Input Module

(schematic)

Features

 0…10 VDC, 2…10 VDC without pull-up

 0…10 VDC with pull-up (linear graph, e.g., used for wall

module connection)

 0/4…20 mA, needs 499 Ω resistor in parallel

 NTC20kΩ (-50…+150 °C, default)

 NTC10kΩ (-30…+100 °C)

 PT1000-1 (-50…+150 °C)

 PT1000-2 (0…+400 °C)

 NI1000TK5000 (-30…+130 °C)

 PT3000 (-50…+150 °C)

 BALCO500 (-30…+120 °C)

 Binary input

 16-bit resolution

 Configurable offset per input

 Auxiliary voltage: 10 VDC, IMAX = 5 mA

 Sensor failure detection

LONWORKS BUS I/O MODULES – PRODUCT DATA

EN0Z-0980GE51 R0119 6

OPT. AUX. TERMINAL MODULE XS814

A1 A2 A3 A4 A5 A6

7B1 B

CLIOL821A ANALOG INPUT MODULE

9 925

GND GNDGND GNDGNDGNDGNDGND GND GND GND GND

10 1026

AI1 AI2 AI3 AI4

V~0

73 7377

72 72

71 71

COM

AUX

SHIELD

INTERNALLY

CONNECTED

TO DIN RAIL

ACTIVE SENSOR

1: 24V POWER

2: 0...10 VDC SIGNAL

3: GND (24V 0)

AUX. VOLTAGE + POT.

1: SIGNAL

2: GND

3: 10 VDC AUX.

2 2

3 3

1 1

CLIOL...

(24 VAC)

EXTERNAL

GROUND

REQUIRED TO

POWER

EXTERNAL

DEVICES

SELECTED INTERNAL CONNECTIONS

MIN. 0.75 mm 2

MIN. 1.5 mm 2

DASHED LINES

THIN LINES

LEGEND:

THICK LINES

MAX. 12 A

MAX. 4 A

Fig. 8. CLIOL821A LonWorks Bus AI Module, wiring example 1: Active sensor and potentiometer

LONWORKS BUS I/O MODULES – PRODUCT DATA

EN0Z-0980GE51 R0119

DRY CONTACT

1: SIGNAL

2: GND

CLIOL821A ANALOG INPUT MODULE

CLIOL... CLIOL...

9 925

GND GNDGND GNDGNDGNDGNDGND GND GND GND GND

10 1026

AI1 AI2 AI3 AI4

V~0

73 7377

72 72

71 71

COM

AUX

SHIELD

INTERNALLY

CONNECTED

TO DIN RAIL

2 22 1 11

DRY

CONTACT

TEMP. SENSOR

(NTC20k or Pt1000)

0(4)...20 mA

1: IN

2: OUT

V~0

COM

EXTERNAL 499 OHM

RESISTOR WITH

TWIN WIRE-END

FERRULES

REQUIRED.

EXTERNAL

DC POWER

SUPPLY

ELECTED INTERNAL CONNECTIONS

MIN. 0.75 mm 2

MIN. 1.5 mm 2

DASHED LINES

THIN LINES

LEGEND:

THICK LINES

MAX. 12 A

MAX. 4 A

Fig. 9. CLIOP821A LonWorks Bus AI Module, wiring example 2: Passive sensor and 0 (4) … 20 mA signal

LONWORKS BUS I/O MODULES – PRODUCT DATA

EN0Z-0980GE51 R0119 8

Analog Output Modules

Fig. 10. CLIOPR822A LonWorks Bus AO Module (shown

with terminal socket)

Legend

1 LONWORKS service button S1

2 Manual overrides

3 Status LEDs

4 Service LED

5 Power LED

NOTE: The hex switch S2 (located next to the LONWORKS

service S1) has no function in combination with a

LONWORKS Bus I/O module. It is used with Panel

Bus I/O modules, only.

The CentraLine LONWORKS Bus Analog Output Modules, with

8 analog outputs, are available in the following models:

 CLIOL822A LONWORKS Bus Analog Output Module

(without manual overrides)

 CLIOLR822A LONWORKS Bus Analog Output Module (with

manual overrides)

They are installed with the XS821-22 or XSU821-22 Terminal

Socket.

71 75

72 76

73 77

GND GND GND GND GND GND GND GND GND GND

AO1

NC NC

AO2 AO3 AO4

O5 AO6 AO7 AO8

18 25 26

COM

ACOM

COM

BCOM

V~ 24

V~0 24

Fig. 11. CentraLine LONWORKS Bus Analog Output

Modules (schematic)

Features

 0…11 VDC, +/-1 mA

 Floating actuator (requires MCD3)

 Binary output (0 V / 10 V)

 red LED per output (brightness according to signal level)

 Optional versions with manual override potentiometers

(Auto, 0…100%; LED flashes in override mode)

 Feedback on manual override signal

 8-bit resolution

 Configurable safety position for outputs in case of

communication problems (remain, 0%, 50%, 100%)

LONWORKS BUS I/O MODULES – PRODUCT DATA

EN0Z-0980GE51 R0119

CLIOL822A ANALOG OUTPUT MODULE

CLIOL...

OPT. AUX. TERMINAL MODULE XS814

925

GND GND

1026

A1 A2 A3 A4 A5 A6

7B1

V~0

73 7377

72 72

71 71

COM

SHIELD

INTERNALLY

CONNECTED

TO DIN RAIL

NC NC

22 1

AO1AO2AO3AO4

23456 7 8

GND GND GNDGNDGNDGND GND GND GND GND

10 11 12 13 14 15 16 17 18

24V DRIVE WITH

0...10 VDC SIGNAL

1: 24V POWER

2: GND (24V 0)

3: 0...10 VDC SIGNAL

S814

(24 VAC)

EXT. GROUND

REQUIRED

TO POWER

EXT. DEVICES

ELECTED INTERNAL CONNECTIONS

MIN. 0.75 mm 2

MIN. 1.5 mm 2

DASHED LINES

THIN LINES

LEGEND:

THICK LINES

MAX. 12 A

MAX. 4 A

Fig. 12. CLIOL822A LonWorks Bus AO Module, wiring example 1: Actuator

LONWORKS BUS I/O MODULES – PRODUCT DATA

EN0Z-0980GE51 R0119 10

CLIOL822A ANALOG OUTPUT MODULE

CLIOL...

OPT. AUX. TERMINAL MODULE XS814

925

GND GND

1026

A1 A2 A3 A4 A5 A6

7B1

V~0

73 7377

72 72

71 71

COM

SHIELD

INTERNALLY

CONNECTED

TO DIN RAIL

NC NC

22 1

AO1AO2AO3AO4

23456 7 8

2 1

GND GND GNDGNDGNDGND GND GND GND GND

10 11 12 13 14 15 16 17 18

11 12 13 14 15 16 17 18

1 2 3456 7 8

MCD 3

K1 K2 K3

24V DRIVE WITH

0...10 VDC SIGNAL

1: 24V POWER

2: GND (24V 0)

3: 0...10 VDC SIGNAL

XS814

(24 VAC)

SELECTED INTERNAL CONNECTIONS

MIN. 0.75 mm 2

MIN. 1.5 mm 2

DASHED LINES

THIN LINES

LEGEND:

THICK LINES

MAX. 12 A

MAX. 4 A

EXT. GROUND

REQUIRED

TO POWER

EXT. DEVICES

Fig. 13. CLIOL822A LonWorks Bus AO Module, wiring example 2: Relay Module MCD 3

 The relay module facilitates the control of peripheral devices with high load via the analog outputs.

 Input terminal 17 of MCD3 controls changeover contact K3.

 Relay terminal 18 of MCD3 controls the N.O. contacts (floating outputs) K1, K2.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Steuereinheit Handbücher

Honeywell

Honeywell VC Series Bedienungsanleitung

Honeywell

Honeywell VR400 Series Bedienungsanleitung

Honeywell

Honeywell Gamewell FCI Velociti Series Bedienungsanleitung

Honeywell

Honeywell SOMAT39 Bedienungsanleitung

Honeywell

Honeywell HON 530-E-WG Leitfaden

Honeywell

Honeywell Braukmann T100A Bedienungsanleitung

Honeywell

Honeywell VF5000 Series Bedienungsanleitung

Honeywell

Honeywell NK295C Bedienungsanleitung

Honeywell

Honeywell RV260 Series Bedienungsanleitung

Honeywell

Honeywell D22 Bedienungsanleitung

Honeywell

Honeywell VPI Series Bedienungsanleitung

Honeywell

Honeywell SV2 Series Bedienungsanleitung

Honeywell

Honeywell D04FM Bedienungsanleitung

Honeywell

Honeywell Maxon SMA11 Bedienungsanleitung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Honeywell

Honeywell 4219 Montageanleitung

Honeywell

Honeywell JADE W7220 Bedienungsanleitung

Honeywell

Honeywell SG160S Bedienungsanleitung

Honeywell

Honeywell RA890F Protectorelay Primary Control Installationsanleitung

Honeywell

Honeywell S4965 Series Bedienungsanleitung

Honeywell

Honeywell DCCC6500 Bedienungsanleitung

Honeywell

Honeywell Y8610U Bedienungsanleitung

Honeywell

Honeywell Silent Knight IDP-Monitor-2 Bedienungsanleitung

Honeywell

Honeywell VC Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung