Honeywell Ex-Or MLSUC500 Bedienungsanleitung

MLSUC500 / 1250 Installation Guide 32340084-001 Rev A, 24-Aug-2018. MU1B-0638GE51 R0718A 1

Installation Guide

MLSUC500 / 1250

Important: Retain these instructions

by Honeywell

These instructions shall be used by trained service

personnel only. If the equipment is used in a manner not

specied by these instructions, the protection provided by the

equipment may be impaired.

1Dimensions & Clearances (including optional expansion modules)

3 INSTALLATION

1 BOX CONTENTS 2 STORING

CONTENTS

1 Box Contents.................................................................1

2 Storing ...........................................................................1

3 Installation .....................................................................1

MLSUC500 / 1250

Installation

Instructions - Mounting

(32340084-001)

and enclosure

mounting instructions.

4Field Maintenance.........................................................4

5Disposal.........................................................................4

+85°C 5

-40°C 95%RH

185 mm (7.25”)

300 mm (11.75”)

Allow

Cover clearance

Unit with door open

It is recommended that the installation should comply

with the local electrical safety installation practices (e.g.

HSE Memorandum of Guidance on Electricity at Work

Regulations 1989, USA National Electric Code).

ATTENTION: Observe precautions for handling

electrostatic sensitive devices.

WARNING: Contains no serviceable parts. Do not

attempt to open the unit. Failure to comply may

cause damage to the unit.

335 mm (13.25”)

300 mm (11.75”)

Enclosure

MLS spine terminals

MLSJ8

MLS PSU

MLS circuit breaker

MLS power terminals

2 MLSUC500 / 1250 Installation Guide 32340084-001 Rev A, 24-Aug-2018. MU1B-0638GE51 R0718A

MLSUC500 / 1250 Installation Guide

2Mounting Requirements

3Mount MLSUC500 / 1250

4Connect Power

3 INSTALLATION (continued)

Altitude <2000m (6562’)

Pollution degree 3

Ensure that the enclosure keeps the MLSJ8 within its

required operating temperature range (considering a 24-watt

dissipation).

Do not mount the unit:

▪in an area with excessive moisture, corrosive fumes, or

explosive vapours.

▪where vibration or shock is likely to occur.

▪in a location subject to electrical noise

+60°C 5

-20°C 95%RH

The entry for the power wiring can be made by drilling a

conduit of around 20mm at the bottom or either side of the

enclosure.

The power wiring must be terminated at the MLS power

terminals and circuit breaker and terminal blocks. The MCB

and the terminal blocks are prewired to the MLSJ8 PSU in

the factory.

Note: the MLS circuit breaker and MLS PSU are pre wired

to the MLSJ8.

DO NOT SWITCH ON POWER

The MLSUC500 / 1250 can be wall mounted by xing the

supplied wall mounting lugs to the corner holes on the rear

side as described in the supplied enclosure xing instructions.

Mains

Input

Green/Yellow

Blue

Brown

Alternative xing positions

in four places

MLSUC500 / 1250 Installation Guide 32340084-001 Rev A, 24-Aug-2018. MU1B-0638GE51 R0718A 3

Installation Guide MLSUC500 / 1250

5Connect Ethernet

6Connect MLS Spine

3 INSTALLATION (continued)

The entry for wiring into the main enclosure can be made by

drilling a conduit of around 20mm at the bottom or either side

of the enclosure.

Default Settings IP Address Subnet Mask

PRI (LAN 1) 192.168 .1.140 255.255.255.0

RJ45

Standard Ethernet cable

(Cat 5e twisted pair)

RJ45

Hub / Switch Router

maximum 100 m (109 yds)

Caution: MLSUC500 / 1250 is not compatible with PoE

(Power over Ethernet) networks. Connecting to a PoE

network may cause the unit to stop functioning. In that

event, disconnect it from the network segment and power-

cycle the MLSUC500 / 1250.

≤ 32 devices

RS-485

The MLSUC500 / 1250 assumes the role of Bus Master on

the MLS Spine. This means that all the RB2000s should

be given consecutive, unique non-zero addresses, refer to

RB2000 documents.

The last unit at each end of the MLS spine should be

congured to terminate the two RS485 signal pairs, A-B

and Y-Z. In the case of an RB2000 being the last device this

is simply a matter of sliding the switch behind the address

setting switches to the ON position.

The entry for wiring into the main enclosure can be made by

drilling a conduit of around 20mm at the bottom or either side

of the enclosure.

Note: The spine connections from the MLSJ8 are prewired to

the terminal blocks.

Screen

to further

remote

RB2000’s

MLSUC500 / 1250

RB2000

4 MLSUC500 / 1250 Installation Guide 32340084-001 Rev A, 24-Aug-2018. MU1B-0638GE51 R0718A

MLSUC500 / 1250 Installation Guide

Honeywell Ex-Or reserves the right to revise this publication from time to time and make changes to the content hereof without obligation to notify any

person of such revisions or changes.

Honeywell Ex-Or

St. Mark’s Court, North Street, Horsham, West Sussex, RH12 1BW, UK. Tel:+44 (0)1403 211888 Fax:+44 (0)1403 241608 www.ex-or.com

8Check STAT & BEAT Indicators

9Congure MLSUC500 / 1250

7Switch On Power to MLSUC500 / 1250

6 DISPOSAL

WEEE Directive:

At the end of their useful life the packaging and

product should be disposed of by a suitable

recycling centre.

Do not dispose of with normal household waste.

Do not burn.

5 FIELD MAINTENANCE

MLSUC500 / 1250 requires no routine maintenance.

WARNING: Contains no serviceable parts. Do not

attempt to open the unit. Failure to comply may

cause damage to the unit.

3 INSTALLATION (continued)

MLSUC500 / 1250 Conguration Manual (W6003)

The following information will be useful;

• RB2000 locations.

• Zones and their respective RB2000 address must be clearly marked.

• The Ballast type and timeout period should also be listed.

• Zone identities. Such as room names or numbers.

• LCM locations.

• Emergency Ballasts.

Some of this information may only be available from those who commission the MLS

lighting control system which may or may not be an Ex-Or commissioning Engineer.

Normal operation indication

STAT

BEAT

Fault indications

STAT Contact technical support.

BEAT

Contact technical support.

STAT BEAT

30s

Dieses Handbuch passt für folgende Modelle

Andere Honeywell Steuereinheit Handbücher

Honeywell

Honeywell M5410C1001 Bedienungsanleitung

Honeywell

Honeywell RV283P Bedienungsanleitung

Honeywell

Honeywell satronic DMG 971 Gebrauchsanweisung

Honeywell

Honeywell VP513A Bedienungsanleitung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Honeywell

Honeywell VR8305P4279/U Bedienungsanleitung

Honeywell

Honeywell TS131 Bedienungsanleitung

Honeywell

Honeywell S89C Bedienungsanleitung

Honeywell

Honeywell VP525C Bedienungsanleitung

Honeywell

Honeywell VR8200A Bedienungsanleitung

Honeywell

Honeywell hmr3000 TruePoint Bedienungsanleitung

Honeywell

Honeywell LYNXDM-GSM Montageanleitung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Honeywell

Honeywell QUIETPRO QP100Ex Bedienungsanleitung

Honeywell

Honeywell VS8510 Bedienungsanleitung

Honeywell

Honeywell Braukmann D06G Bedienungsanleitung

Honeywell

Honeywell LC13-510 Bedienungsanleitung

Honeywell

Honeywell SILEN KNIGHT IDP-Relay-6 Bedienungsanleitung

Honeywell

Honeywell ADEMCO 5800RL Bedienungsanleitung

Honeywell

Honeywell DS06D Bedienungsanleitung

Honeywell

Honeywell W8735ER Bedienungsanleitung

Honeywell

Honeywell Fire-Lite Alarms CRF-300-6 Bedienungsanleitung

Honeywell

Honeywell V5832B Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung