Honeywell FIRE-LITE ALARMS TS540/1 Bedienungsanleitung

IPDACT

IP Communicator

IPDACT Dm 371-I

Quick Start Programming Guide using a PC Serial Port

Model TS540/1

1. Requirements

Alarm Panel

•“Contact Id” compatible panel with tone dialing.

•Existing PSTN Service (for backup communication lines).

•PC with RS-232 serial port.

•Console cable for the IPDACT.

Consumption Idle Alarm Transient

IPDACT ver 2 (TS-540/X) (24V) 100mA 120mA 300mA

Internet Access

Either a static IP address (always the same) or a dynamic IP address (could be different every time

a connection is made) are possible.

2. Checklist¹

a. IPDACT console access password (default is 24680)

b. Installer password, required to execute the register command.

c. IP address, subnet mask and gateway for IPDACT2

d. IPDACT account number or client number.

e. IP address, and UDP Port number of the VisorALARM central station

1Please obtain the following information from your central monitoring station.

2 If you have a DHCP server in the network to which the IPDACT connects, these parameters can be obtained automatically.

3. Physical Connections

FROM AP PHONE PSTN TO AP OUT NC OUT NO INPUT TAMPER GND+12/24V

RJ45

ETHERNET

Female JACK

1K EOLR

Connect to the

+24VDC

Nonresetable

Power Supply

Connect to

custormer’s supplied

network equipment

(Cat 5 cable)

MALE PLUG

CONNECTOR

RJ-31, PRIMARY FIRE

PANEL PHONE LINE NON RST

POWER

NOTE: Connections to

the TO AP terminal

are interchangeable

IPDACT Connects to…

TO AP To the PRIMARYFIRE PANEL PHONE LINE.

The connections to the TO AP terminal are interchangeable.

INPUT Connect the supplied 1K resistor

GND / +24V To the 24 VDC power supply from the Fire Alarm Panel (or other

electric supply) This should be 24 VDC from Fire Alarm Panel

Ethernet Network

(RJ45) To a broadband modem/router or a network switch/hub for internet

access.

4. IPDACT Default Configuration

Through ashort circuit in the IPDACT P2 jumper during the start up process, you can

configure the IPDACT with the default factory settings. The process for this is as follows:

1) switch off the IPDACT

2) short circuit the jumper with the supplied berg header,

3) switch on the device,

4) maintain the jumper short circuited during the first A-DLEDs burst (the LEDs

turn on and off) and undo the short circuit during the second burst.

If the process has executed successfully, the IPDACT will display athird burst indicating the

default configuration has been activated.

5. Serial Port Programming

In order to use the serial port, you need to connect the cable designed to this end which

must be obtained either from Firelite or from an authorized distributor. The following

figures show the cable and the connection mode to the IPDACT.

Connect the serial cable to the IPDACT as shown above, the other end to aPC serial port

and use aterminal emulation program (Windows HyperTerminal for example) configuring

the serial port to 9600 bps, 8data bits, 1stop bit, without parity and no flow control. When

you connect the terminal emulation program, you will be asked for a password. The factory

default value is 24680. Enter this and the following menu will appear.

This deals with an options menu where

each option is represented by aletter

preceding the title. Each option accesses

asubmenu or contains aparameter

value. To select an option, enter the letter

representing this and press ENTER.

For device installation, access the Quick

Install menu by pressing cand then

ENTER.The menu displayed in the

second figure will be presented. All the

parameters to install the device are found

in this menu. The steps to complete the

installation are as follows:

1. If in the LAN network where the IPDACT is installed, you have address assignment

through DHCP, go to step 3. If this is not the case, carry out the following steps:

I. Press the “b”key followed by ENTER.You will be asked for the IP

address. Enter the IP address you have been given and press ENTER.

II. You are now asked for the mask. Enter the IP mask you have been

given and press ENTER.

III. OK should now appear on the PC display which will then show the list of

parameters that appear in option b) the parameters that have just been

entered.

Password Accepted

- Main Menu -

Configuration

a) Generic MIP config

b) Transmission Parameters

c) Quick Install

Monitoring

d) General Info

e) Remote Monitor

f) Events

g) IP Connectivity

z) Exit

option: c

-- Quick Install --

a) DHCP client: ON

b) IP addr: 192.168.0.100 mask: 255.255.255.0

c) Gateway IP: 192.168.0.200

d) Account Number: 0

e) Supervisory Main:

f) Supervisory Backup:

g) Maintenance:

h) Port: 80

i) Register MIP

j) Reset

k) AutoRegister MIP

z) Exit

2. Press the “c”key followed by the ENTER. You will be asked for the gateway IP

address. Insert the value indicated for the parameter and then press ENTER.

OK should now appear on the PC display which will then show the list of

parameters that appear in option c) the value that has just been entered.

3. Press dfollowed by the ENTER key. You will be asked for the client subscriber

number. Enter the value indicated for the parameter and then press ENTER.OK

should now appear on the PC display which will then show the list of parameters

that appear in option d) the value that has just been entered.

4. Press efollowed by the ENTER key. You will be asked for the VisorALARM

receiver IP address. Enter the value indicated for the parameter and then press

ENTER.OK should now appear on the PC display which will then show the list of

parameters that appear in option e) the value that has just been entered.

5. Press hfollowed by the ENTER key. You will be asked for the VisorALARM

receiver UDP port. Enter the value indicated for the parameter and then press

ENTER.OK should now appear on the PC display which will then show the list of

parameters that appear in option h) the value that has just been entered.

6. Press jfollowed by the ENTER key to reboot the device so these changes activate.

You will be asked for apassword. Enter 24680,which is the default factory

password value. After a few second, the IPDACT will reboot.

7. After rebooting, you will be asked for a password. Enter 24680 again and the initial

menu will appear in the PC display.

8. Type cand ENTER to access the Quick Install menu once more.

9. Type iand ENTER so the IPDACT register procedure in the VisorALARM receiver

is carried out. You will be asked for apassword. Enter the installer password you

have been given and press ENTER.The OK message should appear after a

maximum of afew seconds and the IPDACT must then switch the relays and light

up the LED located next to these. This indicates that the IPDACT is active and has

correct connectivity with the VisorALARM receiver.

10. Should any problem occur, an ERROR message will appear instead of the OK.

This will be followed by a number which indicates the following:

a. Error on answer:Received data incorrect. Try again. If the error

persists contact the technical service.

b. VAunreachable:There is aproblem in the local network. The

network cable may be disconnected or the IP address for the

IPDACT or gateway is incorrectly configured.

c. No answer:There is aproblem in the connection with the

VisorALARM. This possibly is aproblem in the client’s connection

to Internet, Internet or the network on the central side.

Andere Honeywell Steuereinheit Handbücher

Honeywell

Honeywell Aquatrol W964F Betriebsanleitung

Honeywell

Honeywell D05F Bedienungsanleitung

Honeywell

Honeywell Ex-Or CDW12U5 Installations- und Betriebshandbuch

Honeywell

Honeywell TR120 Bedienungsanleitung

Honeywell

Honeywell ADEMCO 5800RL Montageanleitung

Honeywell

Honeywell SILENT KNIGHT SK-FML Bedienungsanleitung

Honeywell

Honeywell V4297S Bedienungsanleitung

Honeywell

Honeywell Esser IQ8TAL Bedienungsanleitung

Honeywell

Honeywell NetAXS-123 Bedienungsanleitung

Honeywell

Honeywell SV2 Series Bedienungsanleitung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Honeywell

Honeywell PRO3200 Bedienungsanleitung

Honeywell

Honeywell AlarmNet 7845GSM Bedienungsanleitung

Honeywell

Honeywell LCBS Connect Bedienungsanleitung

Honeywell

Honeywell NOTIFIER M710E-CZ Bedienungsanleitung

Honeywell

Honeywell Kromschroder TC 1 Bedienungsanleitung

Honeywell

Honeywell A4021 Series Bedienungsanleitung

Honeywell

Honeywell 5800WAVE - Ademco Wireless Siren Montageanleitung

Honeywell

Honeywell LYNX Series Bedienungsanleitung

Honeywell

Honeywell R4140G Bedienungsanleitung

Honeywell

Honeywell BA295STN-A Series Bedienungsanleitung

Honeywell

Honeywell Braukmann BV300 Bedienungsanleitung

Honeywell

Honeywell S89C Bedienungsanleitung

Honeywell

Honeywell HM 80 Betriebsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung