Honeywell SILENT KNIGHT SK-FML Bedienungsanleitung

P/N LS10178-001SK-E Rev A

ECN: 17-0196

SK-FML/SK-FSL Fiber Option

Modules Installation Instructions

Section 2: SK-FML/SK-FSL

Specifications

Table 2.1 lists the SK-FML multi-mode fiber-optic

digital audio ports specifications.

Table 2.2 lists the SK-FSL single-mode fiber-optic

digital audio ports specifications.

Section 1: Description

The Silent Knight/Farenhyt Emergency

Communication Systems that use the ECS-NVCM

(Network Voice Control Module) and the Silent

Knight/Farenhyt Fire Alarm Control Panels that use

the SK-NIC (Network Interface Card) support two

types of fiber-option modules to convert wire to fiber.

• SK-FML (Fiber-Optic

Multi-Mode, Receiver) • SK-FSL (Fiber-Optic

Single-Mode, Transmitter)

SK-FML (Fiber-Optic Multi-Mode, Receiver)

The SK-FML is a fiber module that is used as one

channel to transmit or receive communications with

the ECS-NVCM (Network Voice Control Module) or

SK-NIC (Network Interface Card). It allows the multi-

mode fiber to network between the SK-FML module

boards.

Figure 1.1 illustrates the SK-FML fiber module.

Figure 1.1 SK-FML Circuit Board

SK-FSL (Fiber-Optic Single-Mode, Transmitter)

The SK-FSL is a fiber module that is used as one

channel to transmit or receive communications with

the ECS-NVCM (Network Voice Control Module) or

SK-NIC (Network Interface Card). It allows the

single-mode fiber to network between the SK-FSL

module boards.

Figure 1.2 shows the SK-FSL fiber module.

Figure 1.2 SK-FSL Circuit Board

Table 1.1 lists the models that are assigned to the

ECS-NVCM and SK-NIC.

ECS-NVCM SK-NIC

IFP-2100ECS IFP-75 IFP-2100 6808

IFP-300ECS IFP-300 6700 6820/6820EVS

Table 1.1 Network Voice and Interface Card

Modules

SK-FML Specifications

Type of Connector: Type ST

Maximum

Attenuation: 8 dbB for multi-mode with

62.5/125 micrometer cable

@ 200 µ.

Current Draw:

Standby Current: 0.053 A

Alarm Current: 0.053 A

Environment Rating: 32° to 120°F (0° to 49°C),

0% to 93%

Relative Humidity: Non-condensing at 90°F (30°C)

Table 2.1 SK-FML

SK-FSL Specifications

Type of Connector: Type LC

Maximum

Attenuation: 30 dB for multi-mode with 9/125

micrometer cable @ 1310 nm.

Current Draw:

Standby Current: 0.079 A

Alarm Current: 0.079 A

EnvironmentRating: 32° to 120°F (0° to 49°C),

0% to 93%

Relative Humidity: Non-condensing at 90°F (30°C)

Table 2.2 SK-FSL

firealarmresources.com

SK-FML/SK-FSL Fiber Option Modules Installation Instructions

2P/N LS10178-001SK-E Rev A

ECN: 17-0196

Section 3 Installation

Section 3.2 SK-FML/SK-FSL Installation

Section 3.1 Installation Requirements

CAUTION: STATIC SENSITIVE EQUIPMENT:

THIS EQUIPMENT IS SENSITIVE TO STATIC

ELECTRICITY. IT MAY BE DAMAGED IF NOT

PROPERLY HANDLED. TRANSPORTAND STORE

THIS UNIT INASTATIC-SHIELDING BAG.

FAILURE TO OBSERVE THIS REQUIREMENT

COULD CAUSE LATENT DAMAGE TO THE

EQUIPMENT WHICH MIGHT NOT MANIFEST ITSELF

UNTILAFTER THE EQUIPMENT IS PLACED IN

SERVICE.

DISCONNECT ALL POWER:

REMOVE ALL SOURCES OF POWER BEFORE YOU

SERVICE, REMOVE OR INSTALLANY UNITS.

All components should be located per the following

requirements:

• Installations are to be indoors only, in dry loca-

tions, protected from rain, water, and rapid

changes in temperature that could cause con-

densation. Equipment must be securely

mounted on rigid, permanent walls.

• Operating temperature shall not exceed the

range of 32° to 120° F (0 to 49° C).

• Operating humidity not to exceed 93% non-con-

densing at 90° F (32° C).

• All sub-assemblies and components are to be

located in compliance with the local, the national

codes and the manufacturer’s recommenda-

tions.

• All installation field wiring shall be in compliance

with the local code, the national code and the

manufacturer’s recommendations.

• Use the Architects and Engineering Specifica-

tions for detailed information on your Facility’s

Configuration.

1. Remove the unit from its static-shield bag,

observing proper static protection measures.

2. Visually inspect the unit for damage.

If any components are damaged, notify the

shipping carrier immediately. Report missing

components to the Silent Knight Customer

Service.

3. Use the Hardware Kit provided with the unit.

4. Plug the Fiber Module #1 into P6 of the ECS-

NVCM or SK-NIC circuit as shown in Location 1

in Figure 3.2.1 and Figure 3.2.2.

5. To connect the Fiber Module # 1 to the ECS-

NVCM or SK-NIC, insert and secure three

screws (#4-40 x 1/4”) as shown in Location 2 in

Figure 3.2.1 and Figure 3.2.2.

Section 3.2 SK-FML/SK-FSL Installation

(continued)

6. Plug the Fiber Module #1 into P5 of the

ECS-NVCM or SK-NIC circuit as shown in

Location 3 in Figure 3.2.1 and Figure 3.2.2.

7. To connect the Fiber Module #1 to the ECS-

NVCM or SK-NIC, insert and secure three

screws (#4-40 x 1/4”) as shown in Location 4 in

Figure 3.2.1 and Figure 3.2.2.

Figure 3.2.1 illustrates the SK-FML/SK-FSL installed

to the SK-NIC.

Note: FIBER MODULES:SK-FSLAND SK-FML. INSTALL

A MAXIMUM OF TWO BOARDS PER

INSTALLATION.THE FIBER MODULES CAN BE

COMBINED.

Figure 3.2.1 SK-FML Installation

Figure 3.2.2 illustrates the SK-FML/SK-FSL installed

to the ECS-NVCM.

Figure 3.2.2 SK-FSL Installation

SK-NIC

SK-FML

SK-FSL

ABAB

SK-FML

SK-FSL

FIBER MODULE #2

FIBER MODULE #1

SCREW

(#4-40 X ¼”)

(6.35 mm)

(3 PLACES)

SCREW

(#4-40 X ¼”)

(6.35 mm)

(3 PLACES)

—OUT+

VBUS2

—IN+

—OUT+

VBUS1

—IN+

PORT1

ABPORT2

CMD2

COMMONCMD1AUXAUDIO

GNDIN

SK-FML

SK-FSL

ECS-NVCM

FIBER MODULE #2

FIBER MODULE #1

SCREW

(#4-40 X ¼”) (6.35 mm)

(3 PLACES)

SCREW

(#4-40 X ¼”) (6.35 mm)

(3 PLACES)

firealarmresources.com

SK-FML/SK-FSL Fiber Option Modules Installation Instructions

P/N LS10178-001SK-E-A 3

Section 4 Wiring

Section 4.2 SK-FML Installation Wiring

Terminals

Table 4.2.1 lists the SK-FML installation wiring

terminals.

Table 4.2.2 lists the SK-FML switch settings and

drive currents.

Section 4.4 SK-FSL Installation Wiring

Terminals

Table 4.4.1 lists the SK-FML installation wiring

terminals.

Section 4.2 and Section 4.4 list the wiring for the

fiber-optic modules.

• Fiber-Optic Multi-Mode

Module (SK-FML) • Fiber-Optic Single-

Mode Module (SK-FSL)

Section 4.1 SK-FML Circuit Board

Diagram

Figure 4.1.1 illustrates the SK-FML PCB circuit

board diagram.

Figure 4.1.1 SK-FML Circuit Board Diagram

Designation Description

J1 Connects to the transmitting fiber.

(See Note)

J2 Connect to the receiving fiber.

(See Note)

SW1-1 Sets the optical output power for the

transmitting fiber. (See Table 4.2.2)

SW1-2 Sets the optical output power for the

transmitting fiber. (See Table 4.2.2)

SW1-3 Sets the optical output power for the

transmitting fiber. (See Table 4.2.2)

SW1-4 Not used.

P1 Plugs onto P5 (Port 1) or P6 (Port 2) of

the ECS-NVCM or SK-NIC.

NOTE: Use standard ST connector fiber-optic

cable, multi-mode, up to 200 µ (optimized for

62.5/125 µ). Signal loss up to 8dB maximum

between nodes.

Table 4.2.1 SK-FML Terminal Wiring Designations

FIBER-IN

FIBER-OUT

SW1-1 SW1-2 SW1-3 Drive

Current

OFF OFF OFF 10 mA

OFF OFF ON 20 mA

OFF ON OFF 32 mA

OFF ON ON 42 mA

ON OFF OFF 54 mA

ON OFF ON 64 mA

ON ON OFF 76 mA

ON ON ON 86 mA

NOTE: SW1-4 is not used.

Table 4.2.2 SK-FML Switch Settings/Drive Currents

Section 4.3 SK-FSL Circuit Board

Diagram

Figure 4.3.1 illustrates the SK-FSL, PCB circuit

board diagram.

Figure 4.3.1 SK-FSL Circuit Board Diagram

Designation Description

J1 Plugs on to P5 (Port 1) or P6 (Port 2)

of the ECS-NVCM or SK-NIC.

U6 Top connection connects to the

receiving fiber (IN).

Bottom connection connects to the

transmitting fiber (OUT).

NOTE: Use LC connector fiber-optic cable, single

mode, up to 1310 nm (optimized for 9/125 µ).

Signal loss up to 30 dB maximum between nodes.

Table 4.4.1 SK-FML Terminal Wiring Designations

J1 U6 FIBER IN

FIBER OUT

LED1

LED2

firealarmresources.com

SK-FML/SK-FSL Fiber Option Modules Installation Instructions

4P/N LS10178-001SK-E-A

Table 4.4.2 lists the SK-FSL LED Indicators. Section 5:Reference Documentation

Table 5.1 lists the UL-Controlled documentation

assigned to the Silent Knight Systems. If you require

detailed installation instructions on cabinetry, wiring

and specifications, you can download the following

UL-Controlled documents from the ESD site on the

Silent Knight Website (www.silentknight.com).

LED # Name Color Description

1 TX Green Lights while data is

transmitted on the Repeater.

When activity is detected, the

TX light flickers and turns ON.

If no activity is detected, the

TX light turns OFF.

2 RX Green Lights while data is received

on the Repeater.

When activity is detected, the

RX light flickers and turns ON.

When no activity is detected,

the RX light turns OFF.

Table 4.4.2 SK-FSL LED Indicators

Part Number Title

LS10143-001SK-E IFP-2100/ECS Installation and

Operation Manual

LS10144-001SK-E 6820-EVS Installation and

Operation Manual

LS10145-001SK-E IFP-300/ECS Installation and

Operation Manual

LS10146-001SK-E 6808 Installation and Operation

Manual

LS10147-001SK-E IFP-75 Installation and

Operation Manual

LS10148-001SK-E 6700 Installation and Operation

Manual

LS10169-001SK-E ECS-NVCM Installation Sheet

LS10171-001SK-E SK-NIC Installation Sheet

Table 5.1 Reference Documentation

firealarmresources.com

Dieses Handbuch passt für folgende Modelle

Andere Honeywell Steuereinheit Handbücher

Honeywell

Honeywell NK295C Bedienungsanleitung

Honeywell

Honeywell SUPER TRADELINE S8610U Bedienungsanleitung

Honeywell

Honeywell FIRE-LITE ALARMS TS540/1 Bedienungsanleitung

Honeywell

Honeywell LC13-510 Bedienungsanleitung

Honeywell

Honeywell MI-DCZME Bedienungsanleitung

Honeywell

Honeywell VGF Bedienungsanleitung

Honeywell

Honeywell Compact Corona Series Bedienungsanleitung

Honeywell

Honeywell NOTIFIER XP6-MA Bedienungsanleitung

Honeywell

Honeywell Braukmann D06G Bedienungsanleitung

Honeywell

Honeywell Notifier FCM-1-REL Bedienungsanleitung

Honeywell

Honeywell Braukmann D05 Bedienungsanleitung

Honeywell

Honeywell S7800A1167 Bedienungsanleitung

Honeywell

Honeywell S9240F1004 Bedienungsanleitung

Honeywell

Honeywell Velociti Series Bedienungsanleitung

Honeywell

Honeywell D15SN A Series Bedienungsanleitung

Honeywell

Honeywell GENT S4-34410 Gebrauchsanweisung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Honeywell

Honeywell Elster Jeavons S300 Bedienungsanleitung

Honeywell

Honeywell Kromschroder GIK Series Bedienungsanleitung

Honeywell

Honeywell NOTIFIER ASY-01-044-NIM Bedienungsanleitung

Honeywell

Honeywell CF4680 Bedienungsanleitung

Honeywell

Honeywell NOTIFIER XP10-M Bedienungsanleitung

Honeywell

Honeywell Notifier XP6-C Bedienungsanleitung

Honeywell

Honeywell RV181 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung