Honeywell GSMVLP5 Montageanleitung

800-08115 1/11 Rev. B

GSMVLP5 GSM and

ILP5 Ethernet

Communications Modules

Installation and Setup Guide

Installing Communication Modules

RF Exposure

WARNING: The antenna(s) used for this transmitter must be installed to provide a separation distance of

at least 20 cm from all persons and must not be co-located or operating in conjunction with any other

antenna(s) or transmitter.

Installing the GSMVLP5 in the LYNX Touch Series Control

Ensure that SIM card and the connector board are securely installed in the GSMVLP5 before installing the

module in the LYNX Touch.

1. Install the provided FCC/IC label (P/N 800-08334) on the control’s case back (refer to Figure 1).

5000-100-186-V0

FCC ID: CFS-8DLLYNXTOUCH1

IC: 573F-LYNXTOUCH1

THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES AND RSS 210 OF INDUSTRY

CANADA. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS

DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST

ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY

CAUSE UNDESIRED OPERATION.

800-08126 1/11 Rev A

LYNX TOUCH SERIES

COMPLIES WITH FCC RULES, PART 68 FCC REGISTRATION NO.: AC3AL05BL5000

RINGER EQUIVALENCE: 0.1B

IC MODEL: LYNXTOUCH1

CONTAINS TRANSMITTER MODULE

IC: 7830A-MC55I

FCC ID: QIPMC55I

800-08334 2/11 Rev A

FCC ID: CFS-8DLLYNXTOUCH1

IC: 573F-LYNXTOUCH1

LYNX TOUCH SERIES

IC MODEL: LYNXTOUCHG1

Figure 1. FCC/IC Label Location

2. Release the LYNX Touch front case from the back case by depressing the two locking tabs at the top of the

unit with the blade of a medium size screwdriver (Refer to Figure 2).

3. Install the GSMVLP5 into the LYNX Touch control front case. Ensure that the connector board is properly

seated into the receptacle on the control (Refer to Figure 2).

4. Secure the GSMVLP5 with the three provided screws (Refer to Figure 2).

5. Enable the GSMVLP5 device, configure alarm reporting and module supervision and register the device.

Refer to the “Program the Radio” and “Diagnostics” sections in the LYNX Touch Series Installation and

Setup Guide (P/N 800-06834 or higher).

For Documentation and Online Support: http://www.security.honeywell.com/hsc/resources/MyWebTech

SCREW

(3)

SIM

CARD

5000-100-151-V1

ROTATED

180

CONNECTOR

BOARD

CONNECTOR

BOARD

RECEPTACLE

GSMVLP5

LYNX TOUCH

LOCKING TABS

Figure 2. Installing the GSMVLP5 in the LYNX Touch

Installing the ILP5 in the LYNX Touch Series Control

Ensure that the connector board and cable are securely installed in the ILP5 before installing the module

the LYNX Touch.

1. Release the LYNX Touch front case from the back case by depressing the two locking tabs at the top of the

unit with the blade of a medium size screwdriver (Refer to Figure 3).

2. Using a wire cutter or knife cut the plastic tabs that secure the ILP5 spacer to the back case of the LYNX

Touch (Refer to Figure 3).

3. Remove the ILP5 receptacle knockout from the left side of the LYNX Touch back case (Refer to Figure 3).

4. Install the ILP5 into the LYNX Touch control front case. Ensure that the connector board is properly seated

into the receptacle on the control (Refer to Figure 3).

5. Secure the ILP5 with the three provided screws (Refer to Figure 3).

6. Insert the ILP5 receptacle and spacer into the slot on the back case (Refer to Figure 3).

7. Secure the communications cable to the tie wrap point on the ILP5 with the provided tie wrap (Refer to

Figure 3).

8. Enable the ILP5 and configure alarm reporting and module supervision and register the device. Refer to the

“Program the Radio” and “Diagnostics” sections in the LYNX Touch Series Installation and Setup Guide

(P/N 800-06834 or higher).

For Documentation and Online Support: http://www.security.honeywell.com/hsc/resources/MyWebTech

5000-100-154-V1

SCREW

(3)

ROTATED

180

CONNECTOR

BOARD

RJ45

RECEPTACLE

CONNECTOR BOARD

RECEPTACLE

ILP5

LYNX TOUCH

TIE

WRAP

POINT

REMOVE ILP5

SPACER

ILP5 SPACER

REMOVE ILP5

KNOCKOUT

TIE

WRAP

(1)

RJ45 RECEPTACLE

LYNX TOUCH

ALTERNATE INSTALLATION

LOCKING TABS

ETHERNET CABLE

TO ILP5

Figure 3. Installing the ILP5 in the LYNX Touch

Electrical Specifications

GSMVLP5

Voltage Input 5V

Current

Idle 15 mA, standby

Average 300mA, average transmit

Peak 1.6A peak transmit, 25% duty cycle

ILP5

Voltage Input 5V

Current: 83 mA, 100 Base T with traffic

41 mA, 10 Base T with traffic

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

www.honeywell.com/security

Ê800-08115!Š

800-08115 1/11 Rev. B

Inhaltsverzeichnis

Andere Honeywell Steuereinheit Handbücher

Honeywell

Honeywell LYNXDM-GSM Montageanleitung

Honeywell

Honeywell BCU 370 Handbuch

Honeywell

Honeywell WV8840B Bedienungsanleitung

Honeywell

Honeywell NOTIFIER FCM-1 Bedienungsanleitung

Honeywell

Honeywell LYNX TOUCH 2 Series Bedienungsanleitung

Honeywell

Honeywell M5410C1001 Bedienungsanleitung

Honeywell

Honeywell XW100 Bedienungsanleitung

Honeywell

Honeywell 2MLL-PSRA Bedienungsanleitung

Honeywell

Honeywell Exi-/MaxLED T2 Bedienungsanleitung

Honeywell

Honeywell ESSER IQ8MCP Bedienungsanleitung

Honeywell

Honeywell V4043A Bedienungsanleitung

Honeywell

Honeywell NOTIFIER 020-772 Bedienungsanleitung

Honeywell

Honeywell IDENT KEY 3 Bedienungsanleitung

Honeywell

Honeywell krom schroeder IFD 258 Bedienungsanleitung

Honeywell

Honeywell Krom Schroder PFU 780 Handbuch

Honeywell

Honeywell HON HSV086 Handbuch

Honeywell

Honeywell V5055 Bedienungsanleitung

Honeywell

Honeywell S89E Bedienungsanleitung

Honeywell

Honeywell BA295 Compact Bedienungsanleitung

Honeywell

Honeywell Silent Knight SK-Monitor Bedienungsanleitung

Honeywell

Honeywell VS8521 Bedienungsanleitung

Honeywell

Honeywell SILENT KNIGHT Farenhyt Series Bedienungsanleitung

Honeywell

Honeywell RV181 Bedienungsanleitung

Honeywell

Honeywell JADE W7220 Bedienungs- und Wartungshandbuch

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung