Honeywell Silent Knight SK-Monitor Bedienungsanleitung

SPECIFICATIONS

Normal Operating Voltage: 15 to 32 VDC

Maximum Current Draw: 5.0 mA (LED on)

Average Operating Current: 375µA (group poll), 350 µA (direct poll), 600 µAmps (communication, IDC shorted)

EOL Resistance: 47K Ohms

Max. IDC wiring resistance: 1,500 Ohms

Maximum IDC Voltage: 11 Volts

Maximum IDC Current: 450µA

Temperature Range: 32°F to 120°F (0°C to 49°C)

Humidity: 10% to 93% Non-condensing

Dimensions: 41⁄2˝ H x 4˝ W x 11⁄4˝ D (Mounts to a 4˝ square by 21⁄8˝ deep box.)

Accessories: SMB500 Electrical Box

BEFORE INSTALLING

This information is included as a quick reference installation guide. Refer to

the control panel installation manual for detailed system information. If the

modules will be installed in an existing operational system, inform the opera-

tor and local authority that the system will be temporarily out of service. Dis-

connect power to the control panel before installing the modules.

NOTICE: This manual should be left with the owner/user of this equipment.

GENERAL DESCRIPTION

The SK-Monitor Module is intended for use in intelligent, two-wire systems,

where the individual address of each module is selected using the built-in

rotary switches. It provides either a Class A or Class B fault tolerant initiating

device circuit (IDC) for normally open contact fire alarm and supervisory de-

vices, or either normally open or normally closed security devices. The mod-

ule has a panel controlled LED indicator.

COMPATIBILITY REQUIREMENTS

To ensure proper operation, this module shall be connected to a compatible

Silent Knight system control panel (list available from Silent Knight).

FIGURE 1. CONTROLS AND INDICATORS:

C1067-00

MOUNTING

The SK-Monitor mounts directly to 4-inch square electrical boxes (see Figure

2). The box must have a minimum depth of 21⁄8inches. Surface mounted elec-

trical boxes (SMB500) are available from Silent Knight.

INSTALLATION AND MAINTENANCE INSTRUCTIONS

SK-460-013 1 I56-3442-000

SK-Monitor Module

FIGURE 2. MODULE MOUNTING:

NOTE: For UL Listed security installations, the SK-Monitor must be mounted

within the control panel enclosure.

ISOLATED

QUADRANT

C1066-00

WIRING

NOTE: All wiring must conform to applicable local codes, ordinances, and

regulations. This module is intended for power limited wiring only.

1. Install module wiring in accordance with the job drawings and appropri-

ate wiring diagrams.

2. Set the address on the module per job drawings.

3. Secure module to electrical box (supplied by installer), as shown in Figure 2.

I56-3442-000

7550 Meridian Circle, Maple Grove, MN 55369-4927

763-493-6455; 800-328-0103 Fax: 763-493-6475

http://www.silentknight.com

FIGURE 3. TYPICAL 2-WIRE INITIATING CIRCUIT CONFIGURATION, NFPA STYLE B OR SECURITY SYSTEMS:

NOTE: For UL Listed security installations, the SK-Monitor must be mounted within the control panel enclosure.

(+)

(–)

(+)

(–)

(+)

(–)

MONITOR

MODULE

ANY NUMBER OF UL LISTED CONTACT

CLOSURE DEVICES MAY BE USED. DO NOT MIX

FIRE ALARM INTIATING, SUPERVISORY, OR

SECURITY DEVICES ON THE SAME MODULE.

TO NEXT

DEVICE

FROM PANEL OR

PREVIOUS DEVICE

47K EOL

RESISTOR

ELR-47K

CONNECT MODULES TO LISTED COMPATIBLE

CONTROL PANELS ONLY

SIGNAL LINE CIRCUIT (SLC)

32 VDC MAX.

TWISTED PAIR

IS RECOMENDED

ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED

INITIATING DEVICE CIRCUIT (IDC) - NFPA STYLE B

POWER LIMITED: 450µA MAX. @ 11 VDC MAX

INSTALL CONTACT CLOSURE DEVICES PER

MANUFACTURER’S INSTALLATION INSTRUCTIONS.

C0918-00

FIGURE 4. TYPICAL 4-WIRE FAULT TOLERANT INITIATING CIRCUIT CONFIGURATION, NFPA STYLE D:

(+)

(-)

(+)

(–)

(+)

(–)

TO NEXT

DEVICE

ANY NUMBER OF UL LISTED CONTACT

CLOSURE DEVICES MAY BE USED. DO NOT MIX

FIRE ALARM INTIATING, SUPERVISORY, OR

SECURITY DEVICES ON THE SAME MODULE.

MONITOR

MODULE

FROM PANEL OR

PREVIOUS DEVICE

CONNECT MODULES TO LISTED COMPATIBLE

CONTROL PANELS ONLY

SIGNAL LINE CIRCUIT (SLC)

32 VDC MAX.

TWISTED PAIR

IS RECOMENDED

ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED

INSTALL CONTACT CLOSURE DEVICES PER

MANUFACTURER’S INSTALLATION INSTRUCTIONS.

EOL RESISTOR IS

INTERNAL AT

TERMINALS 8 & 9

C0919-00

SK-460-013 2 I56-3442-000

Inhaltsverzeichnis

Andere Honeywell Steuereinheit Handbücher

Honeywell

Honeywell D06F Bedienungsanleitung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Honeywell

Honeywell L91A Bedienungsanleitung

Honeywell

Honeywell HM 80 Betriebsanleitung

Honeywell

Honeywell RM7800L1087 Bedienungsanleitung

Honeywell

Honeywell S8600A Bedienungsanleitung

Honeywell

Honeywell SV2 Series Bedienungsanleitung

Honeywell

Honeywell PWT-BV Bedienungsanleitung

Honeywell

Honeywell Kromschroder TC 1 Bedienungsanleitung

Honeywell

Honeywell LYNX Series Bedienungsanleitung

Honeywell

Honeywell Gamewell FCI Velociti Series Bedienungsanleitung

Honeywell

Honeywell Notifier FMM-1 Bedienungsanleitung

Honeywell

Honeywell V48F Bedienungsanleitung

Honeywell

Honeywell SG160S Bedienungsanleitung

Honeywell

Honeywell VP525C Bedienungsanleitung

Honeywell

Honeywell BRAUKMANN SG 162 Bedienungsanleitung

Honeywell

Honeywell VR8205 Bedienungsanleitung

Honeywell

Honeywell NetAXS-123 Bedienungsanleitung

Honeywell

Honeywell Notifier NFG-8 Bedienungsanleitung

Honeywell

Honeywell JADE W7220 Bedienungsanleitung

Honeywell

Honeywell KT73 Bedienungsanleitung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Honeywell

Honeywell Fire-lite FFT Bedienungsanleitung

Honeywell

Honeywell VS8421 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung