Honeywell Krom Schroeder VAN Series Bedienungsanleitung

CONTENTS

· Edition 05.22 · EN · 03250824

DE, EN, FR, NL, IT, ES, DA, SV, NO, PT, EL, TR, CS, PL, RU, HU – www.docuthek.com

Magnetic relief valve VAN

1 Safety ................................1

2 Checking the usage .....................2

3 Installation ............................2

4 Wiring................................2

5 Tightness test..........................4

6 Replacing the actuator ...................4

7 Maintenance...........................5

8 Accessories ...........................5

9 Technical data .........................6

10 Designed lifetime ......................7

11 Certification ..........................7

12 Logistics .............................8

13 Disposal .............................8

1 SAFETY

1.1 Please read and keep in a safe place

Please read through these instructions care-

fully before installing or operating. Following the installa-

tion, pass the instructions on to the operator. This unit

must be installed and commissioned in accordance

with the regulations and standards in force. These

instructions can also be found at www.docuthek.com.

1.2 Explanation of symbols

1, 2, 3, a, b, c = Action

➔= Instruction

1.3 Liability

We will not be held liable for damage resulting from

non-observance of the instructions and non-com-

pliant use.

1.4 Safety instructions

Information that is relevant for safety is indicated in the

instructions as follows:

DANGER

Indicates potentially fatal situations.

WARNING

Indicates possible danger to life and limb.

CAUTION

Indicates possible material damage.

All interventions may only be carried out by qualiﬁed

gas technicians. Electrical interventions may only be

carried out by qualiﬁed electricians.

1.5 Conversion, spare parts

All technical changes are prohibited. Only use OEM

spare parts.

OPERATING INSTRUCTIONS

VAN · Edition 05.22

EN-2

2 CHECKING THE USAGE

Magnetic relief valve, open when de-energized, for the

monitoring of gas valves for tightness used in conjunc-

tion with a visual discharge unit. For purging excess

or leakage gas.

This function is only guaranteed when used within the

speciﬁed limits– see page 6 (9 Technical data). Any

other use is considered as non-compliant.

2.1 Type code

VAN Magnetic relief valve

1–2 Sizes

10–50 Inlet and outlet ﬂange nominal size

RRp internal thread

/N Quick opening, quick closing

WMains voltage 230V AC, 50/60Hz

QMains voltage 120V AC, 50/60Hz

KMains voltage 24V DC

PMains voltage 100V AC, 50/60Hz

YMains voltage 200V AC, 50/60Hz

SClosed position switch with visual posi-

tion indicator

GClosed position switch for 24V with

visual position indicator

LViewing side: left

RViewing side: right



2.2 Part designations

VAN..S,

VAN..G

VAN

1 Solenoid actuator

2 Flow body

3 Connection box

4 Connection ﬂange

5 Closed position indicator

6 Connection parts

7 Sealing plug

2.3 Type label

Mains voltage, electrical power consumption, ambient

temperature, enclosure, inlet pressure and installation

position: see type label.

Elster GmbH

Osnabrück, Germany

.XXXX

VAN

3 INSTALLATION

CAUTION

Incorrect installation

Please observe the following to ensure that the

magnetic relief valve is not damaged during instal-

lation and operation:

– Sealing material and dirt, e.g. thread cuttings,

must not be allowed to get into the valve

housing.

– A ﬁlter must be installed upstream of every

system.

– Dropping the device can cause permanent

damage. In this event, replace the entire device

and associated modules before use.

– Do not clamp the unit in a vice. Only secure the

ﬂange by holding the octagon with a suitable

spanner. Risk of external leakage.

– Solenoid valves with closed position indicator

VAN..S or VAN..G: actuator cannot be rotated.

➔

Install the unit in the pipe free of mechanical stress.

➔

Installation position: black solenoid actu-

ator in the vertical upright position or tilt-

ed up to the horizontal, not upside down.

➔The housing must not be in contact with masonry,

minimum clearance 20mm (0.79").

1 Obey the direction of ﬂow as marked on the hous-

ing.

2 3 4

4 WIRING

WARNING

Risk of injury!

Please observe the following to ensure that no

damage occurs:

– Electric shocks can be fatal! Before working on

possible live components, ensure the unit is

disconnected from the power supply.

– The solenoid actuator heats up during

operation. Surface temperature approx. 85°C

(approx. 185°F).

➔Use temperature-resistant cable (>80°C).

VAN · Edition 05.22

EN-3

1 Disconnect the system from the electrical power

supply.

2 Shut off the gas supply.

➔Wiring to EN60204-1.

➔

Push through and remove the knock-out in the

connection box before removing the cover. If the

M20 cable gland or plug is already ﬁtted, it is not

necessary to remove the knock-out.

3 4

M20 cable gland

a b c

d e

(+)

LV1 N

(-)

Plug

➔LV1(+) = black, N(–) = blue

a b

(+)

LV1 N

(-)

Socket

➔1 = N(–), 2 = LV1(+)

a b c

d e

Closed position indicator

➔VAN open: contacts 1and 2closed, VAN closed:

contacts 1and 3closed.

➔

Indicator of closed position indicator: red = VAN

closed, white = VAN open.

CAUTION

Please observe the following to ensure smooth

operation:

– Route valve and closed position indicator cables

separately through M20 cable glands or use two

separate plugs. Otherwise, there is a risk of

interference between valve voltage and closed

position indicator voltage.

➔To make wiring easier, the connection terminal for

the closed position indicator can be removed.

1 32

LV1

(+)

(-)

COM

Valve open

Valve closed

1 32

LV1

(+)

(-)

COM

Valve open

Valve closed

➔

When installing two plugs on a VAN with closed

position indicator: label the sockets and plugs to

avoid confusion.

COM

Valve open

Valve closed

➔Ensure that the connection terminal for the closed

position indicator has been reconnected.

Finishing the wiring

VAN · Edition 05.22

EN-4

5 TIGHTNESS TEST

1 Close the gas solenoid valve.

2 To be able to check the tightness, shut off the

downstream pipeline close to the valve.

6 Open the solenoid valve.

7 8

9 Tightness OK: open the pipeline.

➔

Pipeline leaking: replace the seal on the ﬂange, see

accessories. Then check for tightness once again.

➔

Unit leaking: remove the unit and return it to the

manufacturer.

6 REPLACING THE ACTUATOR

➔

The actuator adapter set for the new actuator must

be ordered separately.

VAN 2VAN 1

VAx 1, VCx 1: Order No. 74924468,

VAx 2–3, VCx 2–3: Order No. 74924469.

➔The seals of the actuator adapter set are covered

with a non-stick coating. No additional grease is

required.

1 Disconnect the system from the electrical power

supply.

2 Shut off the gas supply.

➔

Remove the M20 cable gland or other type of

connection.

3 4 5

6 7 8

➔

Depending on the construction stage of the unit, there

are two different methods for replacing the actuator:

If the unit concerned has no O-ring in this place

(arrow), replace the actuator as described here.

Otherwise, go to the next note.

b Insert seals.

c Position of the metal ring can be selected.

VAx 1, VAN 1 VAx 2–3, VAN 2

e Slide seal under the second groove.

➔

If the unit concerned has an O-ring in this place

(arrow), replace the actuator as described here:

VAN1: use all seals from the actuator adapter set.

VAN2: use the small seal from the actuator adapter

set and only one of the large seals.

a b

VAx 1–3,

VAN 1–2

c Slide seal under the second groove.

VAN · Edition 05.22

EN-5

10 Position new actuator.

11 Follow the reverse procedure when reassembling.

12 Fit the M20 cable gland or plug and socket.

13 Connect the VAN to the electrical power supply,

see page 2 (4 Wiring).

7 MAINTENANCE

CAUTION

In order to ensure smooth operation, check the

tightness and function of the unit:

– Once per year, twice per year in the case of

biogas; check for internal and external

tightness, see page 4 (5 Tightness test).

– Check electrical installations once a year in line

with local regulations; pay particular attention to

the PEwire, see page 2 (4 Wiring).

➔If the ﬂow rate has dropped, clean the strainer.

➔We recommend replacing the seals, see accesso-

ries, page 6 (8.2 Seal set VA 1–2).

1 Disconnect the system from the electrical power

supply.

2 Shut off the gas supply.

3 Undo connection parts.

4 5 6

7 8

9 Once the seals have been replaced, follow the

reverse procedure to reassemble the unit. Note

the recommended tightening torques for the con-

nection parts.

Connection parts

Tightening

torque

[Ncm]

VAx 1: M5 500 ± 50

VAx 2: M6 800 ± 50

VAx 3: M8 1400 ± 100

10 Then check the unit for internal and external tight-

ness, see page 4 (5 Tightness test).

8 ACCESSORIES

8.1 Pressure switch for gas DG..VC

The pressure switch for gas monitors the inlet pres-

surepuand the outlet pressurepd.

➔

Monitoring the inlet pressure pu: the pressure

switch for gas is mounted on the inlet side.

Monitoring the outlet pressure p

: the pressure

switch for gas is mounted on the outlet side.

Scope of delivery:

1 x pressure switch for gas,

2 x self-tapping retaining screws,

2 x sealing rings.

Also available with gold-plated contacts for voltages

of 5 to 250V.

➔When retroﬁtting the pressure switch for gas, see

enclosed operating instructions “Pressure switch-

es for gas DG..C”, section entitled “Mounting the

DG..C.. on valVario gas solenoid valves”.

➔The switching point is adjustable via hand wheel.

1 2 3

Type

Adjusting range

(adjusting

tolerance =

±15% of the

scale value)

Mean switching

differential at

min. and max.

setting

[mbar] ["WC] [mbar] ["WC]

DG17VC 2–17 0.8–6.8 0.7–1.7 0.3–0.8

DG40VC 5–40 2–16 1–2 0.4–1

DG110VC 30–110 12–44 3–8 0.8–3.2

DG300VC 100–

300 40–120 6–15 2.4–8

➔

Deviation from the switching point during testing

pursuant to EN1854 Gas pressure switches:

±15%.

VAN · Edition 05.22

EN-6

8.2 Seal set VA 1–2

When retroﬁtting accessories or a second valVario

control or when servicing, we recommend replacing

the seals.

VA1, Order No. 74921988,

VA2, Order No. 74921989.

Scope of delivery:

A1 x double block seal,

B1 x retaining frame,

C2 x O-rings (ﬂange),

D2 x O-rings (pressure switch),

for test nipple/screw plug:

E2 x sealing rings (ﬂat sealing),

2 x proﬁled sealing rings.

9 TECHNICAL DATA

9.1 Ambient conditions

Icing, condensation and dew in and on the unit are

not permitted.

Avoid direct sunlight or radiation from red-hot surfaces

on the unit. Note the maximum medium and ambient

temperatures!

Avoid corrosive inﬂuences, e.g. salty ambient air or SO2.

The unit may only be stored/installed in enclosed

rooms/buildings.

The unit is suitable for a maximum installation height

of 2000m AMSL.

Ambient temperature: -20 to +50°C (-4 to +122°F),

no condensation permitted.

Long-term use in the upper ambient temperature

range accelerates the ageing of the elastomer ma-

terials and reduces the service life (please contact

manufacturer).

Storage temperature = transport temperature: -20

to +40°C (-4 to +104°F).

Enclosure: IP65.

This unit is not suitable for cleaning with a high-pressure

cleaner and/or cleaning products.

9.2 Mechanical data

Gas types: natural gas, LPG (gaseous), biogas

(max. 0.1%-by-vol. H2S) or clean air; other types

of gas on request. The gas must be clean and dry

in all temperature conditions and must not contain

condensate.

Medium temperature = ambient temperature.

Max. inlet pressure pu: 500mbar (7.25psig).

Leakage rate: ≤ 500 cm3/h (0.132gal/h).

Closing time: quick closing: <1s.

Switching frequency: max. 15x per minute.

Cable gland: M20x1.5.

Electrical connection: cable with max. 2.5mm2

(AWG12) or plug with socket to EN175301-803.

Duty cycle: 100%.

Power factor of the solenoid coil: cosφ=0.9.

Safety valve:

ClassA, Group2 pursuant to EN13611 and

EN161.

Valve housing: aluminium, valve seal: NBR.

Connection ﬂanges with internal thread:

Rp to ISO7-1, NPT to ANSI/ASME.

9.3 Electrical data

Mains voltage:

230VAC, +10/-15%, 50/60Hz,

200VAC, +10/-15%, 50/60Hz,

120VAC, +10/-15%, 50/60Hz,

100VAC, +10/-15%, 50/60Hz,

24VDC, ±20%.

Power consumption:

Type Voltage Power

VAN1 24V DC 25 W

VAN1 100VAC 25 W (26 VA)

VAN1 120VAC 25 W (26 VA)

VAN1 200VAC 25 W (26 VA)

VAN1 230VAC 25 W (26 VA)

VAN2 24V DC 36 W

VAN2 100VAC 36 W (40 VA)

VAN2 120VAC 40 W (44 VA)

VAN2 200VAC 40 W (44 VA)

VAN2 230VAC 40 W (44 VA)

Contact rating of closed position indicator:

Type Voltage Current

(resistive load)

min. max.

VAN..S

12–

250VAC,

50/60Hz

100mA 3A

VAN..G 12–30V DC 2mA 0.1A

VAN · Edition 05.22

EN-7

Switching frequency of closed position indicator: max.

5x per minute.

Switching

current Switching cycles*

cosφ=1 cosφ=0.6

0.1 500,000 500,000

0.5 300,000 250,000

1 200,000 100,000

3 100,000 –

* Limited to max. 200,000 cycles for heating systems.

9.4 Air ﬂow rate Q

Air ﬂow rate Q for a pressure loss of Δp=1mbar

(0.4"WC):

∆p = 1 mbar (0,4 "WC)

Air ﬂow rate

Q [m3/h] Q [SCFH]

VAN110 4.4 155.4

VAN115 5.6 197.7

VAN120 8.3 293.1

VAN125 10 353.1

VAN225 15.5 547.3

VAN232 19.5 688.5

VAN240 21 741.5

VAN250 22.5 794.5

10 DESIGNED LIFETIME

This information on the designed lifetime is based on

using the product in accordance with these operat-

ing instructions. Once the designed lifetime has been

reached, safety-relevant products must be replaced.

Designed lifetime (based on date of manufacture) in

accordance with EN13611, EN161 forVAN:

Type Designed lifetime

Switching

cycles Time (years)

VAN110 – 225 500,000 10

VAN232 – 250 200,000 10

You can ﬁnd further explanations in the applicable

rules and regulations and on the afecor website (www.

afecor.org).

This procedure applies to heating systems. For ther-

moprocessing equipment, observe local regulations.

11 CERTIFICATION

11.1 Declaration of conformity

We, the manufacturer, hereby declare that the products

VAN with product ID No. CE-0063BU1564 comply with

the requirements of the listed Directives and Standards.

Directives:

– 2014/35/EU – LVD

– 2014/30/EU – EMC

– 2011/65/EU – RoHS II

– 2015/863/EU – RoHS III

Regulation:

– (EU) 2016/426 – GAR

Standards:

– EN161:2011+A3:2013

The relevant product corresponds to the tested type

sample.

The production is subject to the surveillance proce-

dure pursuant to Regulation (EU) 2016/426 AnnexIII

paragraph3.

Elster GmbH

Scan of the Declaration of conformity (D,GB)– see

www.docuthek.com

AGA approved

AGA

Australian Gas Association

Eurasian Customs Union

The product VAN meets the technical speciﬁcations

of the Eurasian Customs Union.

11.2 UKCA certiﬁed

Gas Appliances (Product Safety and Metrology etc.

(Amendment etc.) (EU Exit) Regulations 2019)

BS EN161:2011+A3:2013

11.3 REACH Regulation

The device contains substances of very high concern

which are listed in the Candidate List of the European

REACH Regulation No.1907/2006. See Reach list

HTS at www.docuthek.com.

11.4 China RoHS

Directive on the restriction of the use of hazardous sub-

stances (RoHS) in China. Scan of the Disclosure Table

China RoHS2, see certiﬁcates at www.docuthek.com.

VAN · Edition 05.22

EN-8

12 LOGISTICS

Transport

Protect the unit from external forces (blows, shocks,

vibration).

Transport temperature: see page 6 (9.1 Ambient

conditions).

Transport is subject to the ambient conditions de-

scribed.

Report any transport damage on the unit or packaging

without delay.

Check that the delivery is complete.

Storage

Storage temperature: see page 6 (9.1 Ambient

conditions).

Storage is subject to the ambient conditions described.

Storage time: 6months in the original packaging before

using for the ﬁrst time. If stored for longer than this, the

overall service life will be reduced by the corresponding

amount of extra storage time.

13 DISPOSAL

Devices with electronic components:

WEEE Directive 2012/19/EU – Waste Electrical

and Electronic Equipment Directive

At the end of the product life (number of op-

erating cycles reached), dispose of the pack-

aging and product in a corresponding recycling

centre. Do not dispose of the unit with the usu-

al domestic refuse. Do not burn the product.

On request, old units may be returned carriage paid

to the manufacturer in accordance with the relevant

waste legislation requirements.

We reserve the right to make technical modifications in the interests of progress.

The Honeywell Thermal Solutions family of products includes

Honeywell Combustion Safety, Eclipse, Exothermics, Hauck,

Kromschröder and Maxon. To learn more about our products, visit

ThermalSolutions.honeywell.com or contact your Honeywell Sales

Engineer.

Elster GmbH

Strotheweg 1, D-49504 Lotte

T +49 541 1214-0

[email protected]

www.kromschroeder.com

Global centralized service deployment coordination:

T +49 541 1214-365 or -555

[email protected]

Translation from the German

FOR MORE INFORMATION

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Steuereinheit Handbücher

Honeywell

Honeywell SUPER TRADELINE VR8300A Bedienungsanleitung

Honeywell

Honeywell SILEN KNIGHT IDP-Zone-6 Bedienungsanleitung

Honeywell

Honeywell SOMAT39 Bedienungsanleitung

Honeywell

Honeywell AVS Bedienungsanleitung

Honeywell

Honeywell LTE-L57V Bedienungsanleitung

Honeywell

Honeywell TM300 Bedienungsanleitung

Honeywell

Honeywell V48F Bedienungsanleitung

Honeywell

Honeywell Ex-Or CDH8U5 Installations- und Betriebshandbuch

Honeywell

Honeywell S7800A1001 Bedienungsanleitung

Honeywell

Honeywell 804973 Bedienungsanleitung

Honeywell

Honeywell Ex-Or MLSUC500 Bedienungsanleitung

Honeywell

Honeywell AM-1 Series Bedienungsanleitung

Honeywell

Honeywell BA298I-F Bedienungsanleitung

Honeywell

Honeywell VQ400 Series Bedienungsanleitung

Honeywell

Honeywell Esser IQ8TAL Bedienungsanleitung

Honeywell

Honeywell RV181 Bedienungsanleitung

Honeywell

Honeywell VS8420 Bedienungsanleitung

Honeywell

Honeywell N-1000 Service-Handbuch

Honeywell

Honeywell EIM Installationsanleitung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Honeywell

Honeywell HumidiPRO H6062A1000/U Bedienungsanleitung

Honeywell

Honeywell SV2 Series Bedienungsanleitung

Honeywell

Honeywell D06F Bedienungsanleitung

Honeywell

Honeywell ModBus S7810M Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung