Honeywell NOTIFIER FTM-1 Bedienungsanleitung

NO-460-017 1 I56-3533-000

FTM-1 Firephone Control Module

INSTALLATION AND MAINTENANCE INSTRUCTIONS

BEFORE INSTALLING

This information is included as a quick reference installation guide. Refer to

the control panel installation manual for detailed system information. If the

modules will be installed in an existing operational system, inform the opera-

tor and local authority that the system will be temporarily out of service. Dis-

connect power to the control panel before installing the modules.

NOTICE: This manual should be left with the owner/user of this equipment.

GENERAL DESCRIPTION

Firephone Control Modules are intended for use in intelligent, two-wire

systems, where the individual address of each module is selected using the

built-in rotary switches. This module is used to connect a remote firefighter

telephone to a centralized telephone console. A ringing sound is provided

at each off-hook handset until it is connected to the console. Wiring to indi-

vidual telephone jacks and handsets is supervised, and status is reported to

the panel as NORMAL, TROUBLE, or TELEPHONE. This module has two pairs

of output termination points available for fault-tolerant wiring, and includes a

panel-controlled LED indicator.

COMPATIBILITY REQUIREMENTS

To ensure proper operation, this module shall be connected to compatible

Notifier system control panels only (list available from Notifier).

MOUNTING

This module mounts directly to 4″square electrical boxes (see Figure 2A).

The box must have a minimum depth of 21/8″. Flush mounted electrical boxes

(SMB500) are available.

WIRING

NOTE: All wiring must conform to applicable local codes, ordinances and

regulations.

1. Install module wiring in accordance with the job drawings and appropri-

ate wiring diagrams (Figures 3-4).

2. Set the address on the module per job drawings.

3. Secure module to electrical box (supplied by installer), as shown in

Figure 2.

Figure 1. Controls and Indicators:

Figure 2. Module mounting:

C1059-00

SPECIFICATIONS

Normal Operating Voltage: 15 to 32 VDC

Maximum Current Draw: 7.5 mA (LED on)

Average Operating Current: 2.4mA (LED flashing)

SLC Wiring Resistance: 40 Ohms

Supervisory Wiring Resistance: 50 Ohms

Handset Offhook Resistance: 400 to 1500 Ohms

External Supply Voltage Regulated 24VDC

(between Terminals T10 and T11)

Temperature Range: 32˚F to 120˚F (0˚C to 49˚C)

Humidity: 10% to 93% Noncondensing

Dimensions: 4.5”H × 4.275”W × 1.4”D (Mounts to a 4”square by 21/8”deep box.)

Accessories: SMB500 Electrical Box; CB500 Barrier

C1070-02

I56-3533-000

12 Clintonville Road

Northford, CT 06472-1653

Phone: 203.484.7161

FROM PANEL OR

(+)

(-)

TO NEXT

(+)

(-)

DEVICE

(+)

(-)

(+)

3.9K EOL

RESISTOR

MODULE POLARITIES ARE

SHOWN IN ALARM

32 VDC MAX.

IS RECOMMENDED

BRANCH CIRCUITS

BREAK ALL WIRE TO ENSURE

SUPERVISION OF CONNECTIONS.

DO NOT LOOP WIRE AROUND TERMINALS.

(-)

(+)

TWISTED PAIR

SIGNAL LINE CIRCUIT (SLC)

PREVIOUS DEVICE

(-)

(+)

TELEPHONE CONSOLE

24 VOLTS DC POWER LIMITED

Relay Contact Rating:

24 VDC, 3 Amperes Maximum

TELEPHONE CONSOLE MUST

PROVIDE ITS OWN

WIRING SUPERVISION

ALL WIRING SHOWN IS SUPERVISED

AND POWER LIMITED

CONNECT MODULES TO LISTED COMPATIBLE

NOTIFIER CONTROL PANELS ONLY

FROM PANEL OR

(+)

(-)

TO NEXT

(+)

(-)

DEVICE

(+)

(-)

(+)

3.9K EOL

RESISTOR

MODULE POLARITIES ARE

SHOWN IN ALARM

CONNECT MODULES TO LISTED COMPATIBLE

32 VDC MAX.

IS RECOMMENDED

BRANCH CIRCUITS

BREAK ALL WIRE TO ENSURE

SUPERVISION OF CONNECTIONS.

DO NOT LOOP WIRE AROUND TERMINALS.

ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED

TWISTED PAIR

NOTIFIER CONTROL PANELS ONLY

SIGNAL LINE CIRCUIT (SLC)

PREVIOUS DEVICE

(-)

(+)

(-)

(+)

TELEPHONE CONSOLE

24 VOLTS DC POWER LIMITED

Relay Contact Rating:

24 VDC, 3 Amperes Maximum

TELEPHONE CONSOLE MUST

PROVIDE ITS OWN

WIRING SUPERVISION

NO-460-017 2 I56-3533-000

WARNING

All relay switch contacts are shipped in the standby state (open) state, but may have transferred to the activated (closed) state during shipping. To ensure that

the switch contacts are in their correct state, modules must be made to communicate with the panel before connecting circuits controlled by the module.

Figure 3. Typical circuit conﬁguration, NFPA Style Y:

Figure 4. Typical fault tolerant circuit conﬁguration, NFPA Style Z:

C1076-04

C1077-03

Andere Honeywell Steuereinheit Handbücher

Honeywell

Honeywell krom schroeder IFD 258 Bedienungsanleitung

Honeywell

Honeywell RF CM61NG Bedienungsanleitung

Honeywell

Honeywell SK-Mon-10 Bedienungsanleitung

Honeywell

Honeywell V5097A-E Bedienungsanleitung

Honeywell

Honeywell Esser IQ8TAL Bedienungsanleitung

Honeywell

Honeywell SILENT KNIGHT Farenhyt Series Bedienungsanleitung

Honeywell

Honeywell 9410 Series Gebrauchsanweisung

Honeywell

Honeywell DCCC6500 Bedienungsanleitung

Honeywell

Honeywell VP513A Bedienungsanleitung

Honeywell

Honeywell FV300 Technische Daten

Honeywell

Honeywell MK VI Handbuch

Honeywell

Honeywell CR7075 Bedienungsanleitung

Honeywell

Honeywell Silent Knight SK-Monitor Bedienungsanleitung

Honeywell

Honeywell SILENT KNIGHT IDP-Control-6 Bedienungsanleitung

Honeywell

Honeywell XLS-REL Produkthandbuch

Honeywell

Honeywell TS131 Bedienungsanleitung

Honeywell

Honeywell IntelliDoX Bedienungsanleitung

Honeywell

Honeywell Aquatrol W964F Betriebsanleitung

Honeywell

Honeywell V5011N Bedienungsanleitung

Honeywell

Honeywell VR8215S Bedienungsanleitung

Honeywell

Honeywell R7795A Bedienungsanleitung

Honeywell

Honeywell VS8421 Bedienungsanleitung

Honeywell

Honeywell RV277 Bedienungsanleitung

Honeywell

Honeywell V5055A Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung