Honeywell Silent Knight IDP-Monitor Bedienungsanleitung

C0218-01

C0156-00

C0157-00

Figure 1. Controls and Indicators:

Specifications

Normal Operating Voltage: 15 to 32 VDC

Maximum Current Draw: 5.0 mA (LED on)

Average Operating Current: 375µA (LED flashing)

EOL Resistance: 47K Ohms

Maximum IDC

wiring resistance: 1,500 Ohms

Temperature Range: 32°F to 120°F (0°C to 49°C)

Humidity: 10% to 93% Non-condensing

Dimensions: 41⁄2˝ H x 4˝ W x 11⁄4˝ D

(Mounts to a 4˝ square by

21⁄8˝ deep box.)

Accessories: SMB500 Electrical Box

Figure 2B:

Figure 2A. Module mounting:

NOTE: For UL Listed security installations, the IDP-Monitor

must be mounted within the control panel enclosure.

Before Installing

This information is included as a quick reference installa-

tion guide. Refer to the control panel installation manual

for detailed system information. If the modules will be

installed in an existing operational system, inform the

operator and local authority that the system will be tem-

porarily out of service. Disconnect power to the control

panel before installing the modules.

NOTICE: This manual should be left with the owner/

user of this equipment.

General Description

The IDP-Monitor Module is intended for use in intel-

ligent, two-wire systems, where the individual address of

each module is selected using the built-in rotary switches.

It provides either a Class A or Class B fault tolerant initi-

ating device circuit (IDC) for normally open contact fire

alarm and supervisory devices, or either normally open or

normally closed security devices. The module has a panel

controlled LED indicator.

Compatibility Requirements

To ensure proper operation, this module shall be con-

nected to a compatible Silent Knight system control panel

(list available from Silent Knight).

INSTALLATION AND MAINTENANCE

INSTRUCTIONS

K200-08-00 1 I56-2724-002

TENS

ONES ADDRESS

LOOP

ONES

ADDRESS

TENS

789

56789

TENS

ONES

ADDRESS

LOOP

IDP-Monitor Module

Mounting

The IDP-Monitor mounts directly to 4˝ square electri-

cal boxes (see Figure 2A). The box must have a mini-

mum depth of 21⁄8˝. Surface mounted electrical boxes

(SMB500) are available from Silent Knight.

Wiring

NOTE: All wiring must conform to applicable local

codes, ordinances, and regulations. This module is in-

tended for power limited wiring only.

1. Install module wiring in accordance with the job draw-

ings and appropriate wiring diagrams.

2. Set the address on the module per job drawings.

3. Secure module to electrical box (supplied by installer),

as shown in Figure 2A.

678

TENS

ONES

ADDRESS

LOOP

FROM PANEL OR

(+)

(–)

TO NEXT

(+)

(–)

DEVICE

(+)

(–)

MONITOR

CONNECT MODULES TO LISTED COMPATIBLE

32 VDC MAX.

SHIELDED-TWISTED PAIR

IS RECOMMENDED

SILENT KNIGHT CONTROL PANELS ONLY

PREVIOUS DEVICE

ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED

COMMUNICATION LOSS (OPTIONAL CONNECTION FOR

PANELS WHICH SUPPORTTHIS FEATURE)

47 K EOL

RESISTOR

ELR-47K

ANY NUMBER OF UL LISTED CONTACT CLOSURE

DEVICES MAYBE USED. DO NOT MIX FIRE

ALARM INITIATING, SUPERVISORY

, OR

SECURITY DEVICES ON THE SAME MODULE.

INITIATING DEVICE CIRCUIT (IDC) - NFPASTYLE B

POWER LIMITED: 230A MAX @ 12 VDC MAX

INSTALL CONTACT CLOSURE DEVICES PER

MANUFACTURER'S INSTALLATION INSTRUCTIONS.

MODULE

14K SERIES RESISTOR

SIGNAL LINE CIRCUIT (SLC)

TENS

ONES

ADDRESS

LOOP

MODULE

FROM PANEL OR

(+)

(-)

TO NEXT

(+)

(–)

DEVICE

(+)

(–)

MONITOR

CONNECT MODULES TO LISTED COMPATIBLE

SILENT KNIGHT CONTROL PANELS ONLY

PREVIOUS DEVICE

ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED

EOL RESISTOR

IS INTERNAL AT

TERMINALS 8 & 9.

ANY NUMBER OF UL LISTED CONTACT CLOSURE

DEVICES MAY BE USED. DO NOT MIX FIRE

ALARM INITIATING, SUPERVISORY, OR

SECURITY DEVICES ON THE SAME MODULE.

INSTALL CONTACT CLOSURE DEVICES PER

MANUFACTURER'S INSTALLATION INSTRUCTIONS.

32 VDC MAX

SHIELDED-TWISTED PAIR

IS RECOMMENDED

COMMUNICATION LOSS (OPTIONAL CONNECTION

FOR PANELS WHICH SUPPORT THIS FEATURE)

SIGNAL LINE CIRCUIT (SLC)

456789

TENS

ONES ADDRESS

LOOP

(+)

(–)

(+)

(–)

(+)

(–)

MONITOR

ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED

COMMUNICATION LOSS (OPTIONAL CONNECTION FOR

PANELS WHICH SUPPORTTHIS FEATURE)

47 K EOL

RESISTOR

ELR-47K

ANY NUMBER OF UL LISTED CONTACT CLOSURE

DEVICES MAYBE USED. DO NOT MIX FIRE

ALARM INITIATING, SUPERVISORY

, OR

SECURITY DEVICES ON THE SAME MODULE.

INITIATING DEVICE CIRCUIT (IDC) - NFPASTYLE B

POWER LIMITED: 230A MAX @ 12 VDC MAX

INSTALL CONTACT CLOSURE DEVICES PER

MANUFACTURER'S INSTALLATION INSTRUCTIONS.

MODULE

SIGNAL LINE CIRCUIT (SLC)

32 VDC MAX.

TWISTED PAIR

IS RECOMMENDED

FROM PANEL OR

PREVIOUS DEVICE

CONNECT MODULES TO LISTED COMPATIBLE

SILENT KNIGHT CONTROL PANELS ONLY

TO NEXT

DEVICE

C0805-01

C0804-01

C0806-01

Figure 5. Typical 2-wire initiating circuit configuration for security systems (with alarm versus short capability):

NOTE: For UL Listed security installations, the IDP-Monitor must be mounted within the control panel enclosure.

Figure 4. Typical 4-wire fault tolerant initiating circuit configuration, NFPA Style D:

Figure 3. Typical 2-wire initiating circuit configuration, NFPA Style B:

K200-08-00 2 I56-2724-002

7550 Meridian Circle

Maple Grove, MN 55369-4927

763-493-6455; 800-328-0103

Fax: 763-493-6475

http://www.silentknight.com

Inhaltsverzeichnis

Andere Honeywell Steuereinheit Handbücher

Honeywell

Honeywell V100P Bedienungsanleitung

Honeywell

Honeywell PRO4200 Bedienungsanleitung

Honeywell

Honeywell VF5000 Series Bedienungsanleitung

Honeywell

Honeywell VGF Bedienungsanleitung

Honeywell

Honeywell BA295D-3WH Bedienungsanleitung

Honeywell

Honeywell Silent Knight IDP-Monitor-2 Bedienungsanleitung

Honeywell

Honeywell 3GL Bedienungsanleitung

Honeywell

Honeywell TR80 Installationsanleitung

Honeywell

Honeywell SG160S Bedienungsanleitung

Honeywell

Honeywell FF-SRM200P2 Bedienungsanleitung

Honeywell

Honeywell Braukmann D05 Bedienungsanleitung

Honeywell

Honeywell VR4920Z 1000 Bedienungsanleitung

Honeywell

Honeywell VCZA Series Bedienungsanleitung

Honeywell

Honeywell Compact Corona Series Bedienungsanleitung

Honeywell

Honeywell PM7600B Bedienungsanleitung

Honeywell

Honeywell ADEMCO 4204 Bedienungsanleitung

Honeywell

Honeywell NOTIFIER XP6-MA Bedienungsanleitung

Honeywell

Honeywell SV2 Series Bedienungsanleitung

Honeywell

Honeywell Notifier NZM-100-6 Bedienungsanleitung

Honeywell

Honeywell LYNX Series Bedienungsanleitung

Honeywell

Honeywell Pro-Watch 6000 Bedienungsanleitung

Honeywell

Honeywell REDLINK ERM5220R Bedienungsanleitung

Honeywell

Honeywell S4567A 1001 Bedienungsanleitung

Honeywell

Honeywell CF4680 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung