Honeywell SLATE R8001S9001 Bedienungsanleitung

SL AT E ™

Sub-Base Module

R8001S9001

INSTALLATION INSTRUCTIONS

Scan for more information

SLATE™Sub-Base Module 3

R8001S9001

Application

SLATE™ brings conﬁgurable safety and programmable logic

together into one single platform. The platform can easily be

customized for almost any requirement or application–offering

virtually limitless development opportunities with far less

complexity.

The R8001S9001 SLATE Sub-Base Module provides the ability

for the SLATE system to be mounted via DIN Rail in a panel. All

SLATE modules need this sub-base except for the SLATE Base

Module.

Features

• Quick-mount to standard DIN-Rail

• Locking mechanism

• Provides bus connectivity to all modules

• Connections for remote mounted ﬂame ampliﬁers (remote bus)

and remote pushbutton reset

Speciﬁcations

Electrical Ratings:

Voltage and Frequency (from the Base): 18 VDC (± 1 VDC)

Maximum Total Connected Load: 2.5A

Terminal Ratings: See Table 1

Terminal Description Rating

1 18 V Power 2.5 A max including

modules

2 18 V Ground ---

3 Remote Reset

(Burner Control and

Limit modules only)

Connect to Terminal 2 (18

V Ground) via external

pushbutton

432-00025—01

Terminal Description Rating

4 B (Remote Bus

RS485)

Used for Remote mount-

ed ame ampliers

5 A (Remote Bus

RS485)

Used for Remote mount-

ed ame ampliers

Table 1. Terminal Ratings.

Environmental Ratings

Ambient Temperature:

Operating: -20°F to +150°F (-29°C to +66°C).

Shipping: -40°F to +150°F (-40°C to +66°C)

Humidity: 95% continuous, noncondensing.

Vibration: 0.5G environment

Dimensions: See Fig. 1.

Weight: 5 oz (136 g)

Approvals

Underwriters Laboratories Inc. Listed, File: MP286

IRI acceptable.

Federal Communications Commission: Part 15, Class A

Emissions.

Mounting

DIN Rail (See Fig. 3)

Required Components

R8001A1001 SLATE Base Module

Any other SLATE modules

Optional 5-position terminal block for remote ﬂame ampliﬁer or

remote reset button connections (Phoenix Contact p/n 1754504

or equivalent). See Fig. 2.

SLATE™Sub-Base Module 5

R8001S9001

Fig. 1.

M35384

1-5/32

(29)

7-3/32

(180)

2-21/32 (67)

3-13/32 (86)

Dimensions in in. (mm).

632-00025—01

Fig. 2.

M35430

TERMINAL

DESCRIPTION

18V POWER

18V GROUND

REMOTE RESET (BURNER CONTROL AND LIMIT MODULES ONLY)

B (REMOTE BUS RS485)

A (REMOTE BUS RS485)

1234 5

Sub-base module wiring terminals.

SLATE™Sub-Base Module 7

R8001S9001

Installation

WARNING

Fire or Explosion Hazard Can cause severe injury,

death, or property damage.

Veriﬁcation of safety requirements must be performed

each time a control is installed on a burner to prevent

possible hazardous burner operation.

When Installing This Product

1. Read these instructions carefully. Failure to follow them could

damage the product or cause a hazardous condition.

2. Check the ratings given in the instructions and on the product

to make sure the product is suitable for your application.

Mounting

1. The sub-base module can be mounted on type C 20 DIN rail.

2. Mount the sub-base module ﬁrst. The sub-base has locking

mechanisms on both sides of the module. Pull to unlock

position. See Fig. 3.

832-00025—01

Fig. 3.

M35378

UNLOCKED FROM DIN RAIL LOCKED ONTO DIN RAIL

Sub-base locking mechanisms.

3. Slide sub-base on the DIN rail and lock into place.

4. When securing subsequent sub-base modules make sure

communication ports are aligned and locked into place. See

Fig. 4.

M35386

Connecting additional sub-base modules.

SLATE™Sub-Base Module 9

R8001S9001

5. After securing the sub-base module, snap the SLATE module

into place and secure the module to the sub-base using

screws (included with SLATE module).

Wiring

WARNING

Electrical Shock Hazard.

Can cause severe injury, death or equipment damage.

1. Disconnect the power supply before beginning installation to

prevent electrical shock and equipment damage. More than

one power supply disconnect can be involved.

2. Wiring must comply with all applicable codes, ordinances and

regulations. See Fig. 2.

3. Wiring must comply with NEC Class 1 (Line Voltage) wiring.

Application Recommended Wire

Size

Recommended

Part Numbers

Communication

Lines

22 AWG two-wire

twisted pair with

ground, or ve-wire.

Belden 8723

shielded cable

or equivalent.

Other terminals 18 AWG wire insulat-

ed for voltages and

temperatures for given

application.

TTW60C,

THW75C,

THHN90C

Table 2. Recommended Wire Sizes and Part Numbers.

IMPORTANT

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with these

instructions, may cause interference for radio communications.

It has been tested and found to comply with the limits of a Class

A computing device of part 15 of FCC rules, which are designed

to provide reasonable protection against such interference

10 32-00025—01

when operated in a commercial environment. Operation of this

equipment in a residential area may cause interference; in which

case, the user, at their own expense, may be required to take

whatever measures are required to correct this interference.

1. This digital apparatus does not exceed the Class A limits for

radio noise, set out in the Radio Interfeence Regulations of

the Canadian Department of Communications.

2. Cable shield must be terminated to ground at both ends. If

shielded cable is NOT used, use three-wire twisted cable.

Recommended Grounding Practices

Use an Earth ground or a signal ground as described below.

Earth Ground (Base, Rectiﬁcation Flame Amp

Module, Other Modules Optional)

1. Use to provide a connection between the base and the

control panel of the equipment. Earth ground must be capable

of conducting enough current to blow the breaker in the event

of an internal short circuit.

2. Use wide straps or brackets to provide minimum length,

maximum surface area ground conductors. If a leadwire is

required, use 14 AWG copper wire.

3. Verify that mechanically tightened joints along the ground path

are free of nonconductive coatings and protected against

corrosion on mating surfaces.

Signal ground

Note the 18 V system ground is not electrically connected

to earth ground. Follow local codes and appliance

recommendations to determine if this should be connected to

earth ground.

Recommended Routing of Leadwires

• Do not run high voltage ignition transformer wires in the same

conduit with the ﬂame detector or data lines.

• Do not route ﬂame detector or data lines in conduit with line

voltage circuits.

Inhaltsverzeichnis

Andere Honeywell Steuereinheit Handbücher

Honeywell

Honeywell SLATE Bedienungsanleitung

Honeywell

Honeywell ADEMCO 4229 Montageanleitung

Honeywell

Honeywell RV181 Bedienungsanleitung

Honeywell

Honeywell RF CM61NG Bedienungsanleitung

Honeywell

Honeywell V48F Bedienungsanleitung

Honeywell

Honeywell L506 Bedienungsanleitung

Honeywell

Honeywell S4560B1006 Bedienungsanleitung

Honeywell

Honeywell BA295S Bedienungsanleitung

Honeywell

Honeywell VC Series Bedienungsanleitung

Honeywell

Honeywell MCV2000AA Montageanleitung

Honeywell

Honeywell Elster Jeavons S300 Bedienungsanleitung

Honeywell

Honeywell PWT-BV Bedienungsanleitung

Honeywell

Honeywell RM7823A Bedienungsanleitung

Honeywell

Honeywell L91A Bedienungsanleitung

Honeywell

Honeywell VR4920Z 1000 Bedienungsanleitung

Honeywell

Honeywell Krom Schroeder VAN Series Bedienungsanleitung

Honeywell

Honeywell 2MLF-HO2A Bedienungsanleitung

Honeywell

Honeywell Galaxy 2 Series Bedienungsanleitung

Honeywell

Honeywell V4730C Bedienungsanleitung

Honeywell

Honeywell VCZB Series Bedienungsanleitung

Honeywell

Honeywell DIAL-SET DS05C Bedienungsanleitung

Honeywell

Honeywell V5004TF Bedienungsanleitung

Honeywell

Honeywell IntelliDoX Bedienungsanleitung

Honeywell

Honeywell D05T Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung