Honeywell Velociti AOM-2RF Bedienungsanleitung

AOM-2RF Relay Control Module

INSTALLATION AND MAINTENANCE INSTRUCTIONS

BEFORE INSTALLING

This information is included as a quick reference installation guide. Refer to

the appropriate Gamewell-FCI control panel installation manual for detailed

system information. If the modules will be installed in an existing operational

system, inform the operator and local authority that the system will be tem-

porarily out of service. Disconnect power to the control panel before installing

the modules.

NOTICE: This manual should be left with the owner/user of this equipment.

GENERAL DESCRIPTION

The AOM-2RF Relay Control Module is intended for use in intelligent, two-

wire systems where the individual address of each module is selected using

the built-in rotary switches. It allows a compatible control panel to switch

discrete contacts by code command. The relay contains two isolated sets of

Form-C contacts, which operate as a DPDT switch and are rated in accordance

with the table in the manual. Circuit connections to the relay contacts are

not supervised by the module. The module also has a panel controlled LED

indicator. This module can be used to replace a AOM-2 module that has been

configured for Form-C operation.

COMPATIBILITY REQUIREMENTS

To ensure proper operation, this module shall be connected to a compatible

Gamewell-FCI system control panel (list available from Gamewell-FCI).

SPECIFICATIONS

Normal Operating Voltage: 15 to 32 VDC

Maximum Current Draw: 6.5 mA (LED on)

Average Operating Current: 230µA (LED flashing) Velociti Mode; 255µA (LED flashing) CLIP Mode

EOL Resistance: Not used

Temperature Range: 32˚F to 120˚F (0˚C to 49˚C)

Humidity: 10% to 93% Non-condensing

Dimensions: 4.675" H x 4.275" W x 1.4" D (Mounts to a 4˝ square by 21/8˝ deep box.)

Accessories: SMB500 Electrical Box; CB500 Barrier

I56-3551-006

Velociti ®Series

FIGURE 1. CONTROLS AND INDICATORS:

C1071-00

RELAY CONTACT RATINGS:

CURRENT RATING MAXIMUM VOLTAGE LOAD DESCRIPTION APPLICATION

2 A 25 VAC PF = 0.35 NON-CODED

3 A 30 VDC RESISTIVE NON-CODED

2 A 30 VDC RESISTIVE CODED

0.46 A 30 VDC (L/R = 20MS) NON-CODED

0.7 A 70.7 VAC PF = 0.35 NON-CODED

0.9 A 125 VDC RESISTIVE NON-CODED

0.5 A 125 VAC PF = 0.75 NON-CODED

0.3 A 125 VAC PF = 0.35 NON-CODED

12 Clintonville Road

Northford, CT 06472-1653

Phone: 203.484.7161;

Fax: 203.484.7118

www.gamewell-fci.com

1 I56-3551-006

02-14

WARNING

All relay switch contacts are shipped in the standby state (open) state, but may have transferred to the activated (closed) state during shipping. To ensure that

the switch contacts are in their correct state, modules must be made to communicate with the panel before connecting circuits controlled by the module.

FIGURE 3. RELAY MODULE WIRING DIAGRAM:

MODULE

FROM PANEL OR

(+)

(–)

TO NEXT

(+)

(–)

DEVICE

(+)

(–)

CONTROL

CONNECT MODULES TO LISTED COMPATIBLE

RELAY COMMON 1

RELAY COMMON 2

NORMALLY CLOSED 1

NORMALLY OPEN 2

NORMALLY CLOSED 2

MODULE DOES NOT SUPERVISE CONTROLLED CIRCUITS

NORMALLY OPEN 1

CONTROL PANELS ONLY

PREVIOUS DEVICE

SIGNAL LINE CIRCUIT (SLC)

32 VDC MAX.

TWISTED PAIR

IS RECOMMENDED

UNUSED

*NOTE: ANY FAULT IN THE POWER SUPPLY IS LIMITED TO THAT ZONE AND DOES NOT RESULT IN A FAULT IN A SEPARATE ZONE.

IF ANY WIRING TO TERMINALS 4 – 10 IS NONPOWER

LIMITED, THE CB500 BARRIER IS REQUIRED. THE CB500

INCLUDES A NONPOWER LIMITED LABEL, WHICH MUST

BE PLACED OVER THE POWER LIMITED TERMINAL

INFORMATION ON THE NAMEPLATE LABEL.

C0946-00

MOUNTING

The AOM-2RF mounts directly to 4-inch square electrical boxes (see Figure

2A). The box must have a minimum depth of 21/8inches. Surface mounted

electrical boxes (SMB500) are available from Gamewell-FCI. The module can

also mount to the DNR(W) housing.

FIGURE 2A. MODULE MOUNTING FIGURE 2B.

WITH BARRIER:

C1070-00

WIRING

NOTE: All wiring must conform to applicable local codes, ordinances, and reg-

ulations. When using control modules in nonpower limited applications, the

CB500 Module Barrier must be used to meet UL requirements for the separa-

tion of power-limited and nonpower-limited terminals and wiring. The barrier

must be inserted into a 4˝ × 4˝ × 21/8˝ junction box, and the control module

must be placed into the barrier and attached to the junction box (Figure 2A).

The power-limited wiring must be placed into the isolated quadrant of the

module barrier (Figure 2B).

1. Install module wiring in accordance with the job drawings and appropri-

ate wiring diagrams.

2. Set the address on the module per job drawings.

3. Secure module to electrical box (supplied by installer), as shown in

Figure 2A.

Wire should be stripped to the appropriate length (recommended strip length

is 1/4“ to 3/8”). Exposed conductor should be secured under the clamping plate

and should not protrude beyond the terminal block area. Caution: Do not loop

wire under terminals. Break wire run to provide supervision of connections.

2 I56-3551-006

Velociti®, Gamewell-FCI®, System Sensor®, and Honeywell®are registered trademarks of Honeywell International, Inc.

Dieses Handbuch passt für folgende Modelle

Andere Honeywell Steuereinheit Handbücher

Honeywell

Honeywell BA295STN-11/2C Bedienungsanleitung

Honeywell

Honeywell BCU 460 Handbuch

Honeywell

Honeywell PEHA PHC Bedienungsanleitung

Honeywell

Honeywell VC Series Bedienungsanleitung

Honeywell

Honeywell V5004TF Bedienungsanleitung

Honeywell

Honeywell MAXON 8730 Series Bedienungsanleitung

Honeywell

Honeywell ADEMCO 5843 Montageanleitung

Honeywell

Honeywell Braukmann D06G Bedienungsanleitung

Honeywell

Honeywell Notifier FCM-1 Bedienungsanleitung

Honeywell

Honeywell PEHA 450 FU-SP 2 Bedienungsanleitung

Honeywell

Honeywell FIRE-LITE ALARMS TS540/1 Bedienungsanleitung

Honeywell

Honeywell ADEMCO 4229 Montageanleitung

Honeywell

Honeywell Notifier NFG-8 Bedienungsanleitung

Honeywell

Honeywell Satronic DMG 973 Bedienungsanleitung

Honeywell

Honeywell EXCEL 5000 OPEN T7460A Bedienungsanleitung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Honeywell

Honeywell Elster Jeavons S300 Bedienungsanleitung

Honeywell

Honeywell V5011N Bedienungsanleitung

Honeywell

Honeywell S89C Bedienungsanleitung

Honeywell

Honeywell D15SN A Series Bedienungsanleitung

Honeywell

Honeywell BA295S Bedienungsanleitung

Honeywell

Honeywell CF3680 Bedienungsanleitung

Honeywell

Honeywell PS300 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung