Honeywell AutoRAE 2 Bedienungsanleitung

AutoRAE 2 System

Quick Start Guide

www.sps.honeywell.com

by Honeywell

Setup

Before using the AutoRAE 2 Controller and AutoRAE 2 Cradle(s) to bump test or calibrate ToxiRAE Pro-family,

QRAE 3, MicroRAE, Handheld PID, and/or MultiRAE-family (pumped versions) instruments, follow the

instructions in the AutoRAE 2 User’s Guide for programming the gas configurations. The steps to follow for

assembly and gas configuration, as well as functionality, are the same for all cradles.

Connections

Assemble the system. Connect the AutoRAE 2 Controller to any Cradles, and then connect the Terminator. For

ToxiRAE Pro Cradles, insert the appropriate adapter.

Important! Make sure an SD card is installed in the AutoRAE 2 Controller. The system cannot operate if an SD

card is not installed. For installation instructions, consult the AutoRAE 2 User’s Guide. Make sure the AutoRAE 2

Controller’s RTC (real-time clock) has been set in Safety Suite Device Configurator (SSDC) before its first use.

Calibration gas cylinders

(each must have a demand-

flow regulator)

Attach Controller to Cradle(s) and then

attach Terminal Adapter to last Cradle.

Insert and tighten

screws, and then put

caps over screws.

Press filter onto

receptacle at

end of Cradle

Plug the barrel from AC adapter into

jack. Then plug its cord into the

transformer, and the transformer

into AC power source.

Exhaust

AutoRAE 2

Controller

AutoRAE 2

Cradles

(maximum

of 10)

Press filter onto

receptacle at end

of Controller

The ToxiRAE Pro Cradle requires

an adapter to be inserted in the

capture mechanism. ToxiRAE Pro

EC (L) and ToxiRAE Pro LEL (L)

and ToxiRAE Pro PID (R).

UltraRAE 3000 or ppbRAE 3000 only:

Use an Active Carbon

Filter for VOC filtering

www.sps.honeywell.com

by Honeywell

AutoRAE 2 System

Quick Start Guide

Turning The System On

Toggle the switch on the side of the AutoRAE 2 Controller. The display and power LED glow, and the LEDs on attached

cradles light up. The AutoRAE 2’s internal pump and the valves in the system are tested. If self-checkout is successful, the

system is ready to use. The display provides a list of the AutoRAE 2 Cradles, and if there are instruments in them, the

names of the instruments are included in this list.

Make sure calibration gases match the configurations created in Safety Suite Device Configurator (SSDC) and

transferred to the AutoRAE 2 Controller. Also make sure the gas cylinders have sufficient gas in them and that they

are attached properly.

Place An Instrument In The Cradle

Make sure the filter on the instrument is not dirty or clogged (MiniRAE 3000, ppbRAE 3000, UltraRAE 3000, and

MiniRAE Lite must be equipped with Quick Connectors and have their inlet probes removed).

Important! For MicroRAE, make sure the external filter is removed from the unit before placing it in the Cradle.

1. Make sure the instrument is in AutoRAE 2 Mode or turned off.

2. Place the instrument into the cradle face-down, making sure that it is aligned correctly with the contacts on the

AutoRAE 2 Cradle’s charging port. There are two alignment points on one side and one alignment point on the

other side, designed to mate with matching points on the bottom of the instrument.

3. Press in on the capture mechanism to lock the instrument in place.

Automatic Warm-Up Before Bump Testing Or Calibrating

When you place an instrument in the cradle and lock the capture mechanism, the instrument begins charging and is

automatically warmed up. Warm-up time depends on the sensors installed in the instrument and their individual

warm-up requirements.

Display Color Coding

The AutoRAE 2 Controller has a color display, so colors are used to indicate status in different categories of

information.

Status

Color

Explanation

Pass

Green

1. All sensors and alarms passed bump test.

2. All sensors and alarms passed calibration.

Pass?

Green

1. All sensors that were tested passed bump test. Some sensors were not tested.

2. All sensors that were calibrated passed calibration. Some sensors were not calibrated.

Fail

Red

1. One or more sensors or alarms failed bump test.

2. One or more sensors or alarms failed calibration.

3. Monitor not detected after 30 minutes.

4. Monitor warm-up or other error.

Warning

Yellow

Sensor does not match the gas.

Warm-up

None

Instrument warm-up.

Ready

None

Instrument ready to bump test or calibrate.

MultiRAE

ToxiRAE Pro

QRAE 3

Handheld PID

MicroRAE

www.sps.honeywell.com

AutoRAE 2 System

Quick Start Guide

by Honeywell

Bump Testing

You can bump test all or individually selected instruments that are seated in the system’s cradles.

From the main screen, enter Bump Test by pressing [Y/+] twice (“Function” and then “Select”).

Note: Any cradle that does not have an instrument in it is shown with a gray checkbox. You cannot check/uncheck

this box.

To select all instruments in cradles to bump test:

1. Press [Y/+]. When you check “Bump All,” the “Bump All” checkbox and all of the other checkboxes for

cradled instruments are automatically checked.

2. Press [MODE] for “Done.”

3. Press [Y/+] to start.

To select specific instruments to bump test:

1. Press [N/-] to scroll down the list to an instrument you want to select for bump testing.

2. Press [Y/+] to toggle the selection between unchecked and checked.

3. Press [MODE] for “Done.”

4. Press [N/-] to select “Exit,” and then press [Y/+] to exit.

If you did not press [Y/+] to start the process, then a countdown begins. When the countdown reaches zero, then

the instruments are bump tested.

To abort a bump test: Press [N/-]. You will be asked if you want to abort the process. Press [Y/+] for “Yes” and

[N/-] for “No.”

IMPORTANT!

If an instrument does not pass a bump test, a full calibration is automatically started.

www.sps.honeywell.com

AutoRAE 2 System

Quick Start Guide

by Honeywell

Calibration

You can calibrate all or individually selected instruments that are seated in the system’s cradles.

From the main screen, enter Calibrate by pressing [Y/+] (“Function”), and then [N/-] until “Calibrate” is highlighted.

Then press [Y/+] to select it.

Note: Any cradle that does not have an instrument in it is shown with a gray checkbox. You cannot check/uncheck

this box.

To select all instruments to calibrate:

1. Press [Y/+]. When you check “Calibrate All,” the “Calibrate All” checkbox and all of the other checkboxes

for cradled instruments are checked.

2. Press [MODE] for “Done.”

3. Press [Y/+] to start.

To select specific instruments to calibrate:

1. Press [N/-] to scroll down the list to an instrument you want to select for calibration.

2. Press [Y/+] to toggle the selection between unchecked and checked.

3. Press [MODE] for “Done.”

4. Press [N/-] to select “Exit,” and then press [Y/+] to exit.

If you did not press [Y/+] to start the process, then a countdown begins. When the countdown reaches zero, then the

instruments are calibrated.

To abort calibration: Press [N/-]. You will be asked if you want to abort the process. Press [Y/+] for “Yes” and

[N/-] for “No.”

www.sps.honeywell.com

AutoRAE 2 System

Quick Start Guide

by Honeywell

Removing An Instrument From A Cradle

To remove an instrument from a cradle, press the button to release the capture mechanism. Then lift the instrument

from its inlet end.

Charging An Instrument’s Battery

Each AutoRAE 2 Cradle attached to an AutoRAE 2 Controller automatically charges an instrument’s battery when

it is docked. The Charge Status LED glows red to indicate that charging is taking place. When the instrument’s

battery is fully charged, the LED glows green.

Active Carbon Filter For Removing VOC

Whether zeroing a ppbRAE 3000, an UltrRAE 3000, or in an environment in which the ambient air has VOC

(volatile organic compounds), it is strongly recommended to use an Active Carbon Filter (P/N: 490-0006-000),

which filters out VOC from the air.

When an AutoRAE Controller is used with one or more Cradles, the air inlet on each attached cradle is disabled and

air is taken in through the Controller’s air inlet. Therefore, you only need to use one Active Carbon Filter for the

Controller instead of on each cradle. To install the Active Carbon Filter on the Controller:

1. Remove the standard filter (if one is installed).

2. Remove the plastic filter adapter by twisting the plastic filter clockwise while gently pulling outward.

3. Press the Active Carbon Filter into the receptacle. The filter is designed for 20 uses. To help you keep track

of how many calibrations are performed, there are 20 small boxes painted on the surface of the filter that you

can mark with a pen after each use. Note: Make sure the arrow on the side of the filter points toward the

Controller.

MultiRAE

ToxiRAE Pro

QRAE 3

Handheld PID

Press Active Carbon

Filter into receptacle

Remove standard filter

Remove plastic

filter adapter

MicroRAE

www.sps.honeywell.com

AutoRAE 2 System

Quick Start Guide

by Honeywell

Handheld PID Monitors Must Be Equipped With A Quick Connector

You must remove the inlet probe before placing a handheld PID instrument (MiniRAE Lite, MiniRAE 3000, ppbRAE

3000, or UltraRAE 3000) into the cradle. If the instrument does not have a Quick Connector (P/N: T02-3301-000) already

installed, you must install one.

Installing A Quick Connector

UltraRAE 3000: MiniRAE Lite, MiniRAE 3000, or ppbRAE 3000:

Rev F EN

P/N T02-4002-000

CORPORATE HEADQUARTERS

RAE Systems

by Honeywell

300 S

Tryon St. Suite 500

Charlotte,

NC 28202, USA

Phone:

+1 888 749 8878

Fax:

+1 817 274 8321

rae

-callcenter@honeywell.com

WORLDWIDE SALES OFFICES

USA/Canada:

1.877.723.2878

Europe: +45.86.52.51.55

Middle East: +00971.4.440.5949

China: +86.10.5885.8788

-3000

Asia Pacific: +852.2669.0828

Do not use a RAE-Sep Tube in the

UltraRAE 3000 tube holder when

using it with an AutoRAE 2 Cradle.

Andere Handbücher für AutoRAE 2

Inhaltsverzeichnis

Andere Honeywell Controller Handbücher

Honeywell

Honeywell SLATE Series Bedienungsanleitung

Honeywell

Honeywell T775A/B/M 2000 Series Bedienungsanleitung

Honeywell

Honeywell D6 PRO Bedienungsanleitung

Honeywell

Honeywell ML6275 Bedienungsanleitung

Honeywell

Honeywell Tema-Voyager Multi VMC Series Bedienungsanleitung

Honeywell

Honeywell HercuLink Bedienungsanleitung

Honeywell

Honeywell Spyder PUB6438S Bedienungsanleitung

Honeywell

Honeywell EVOTOUCH CONTROLLER Bedienungsanleitung

Honeywell

Honeywell VU443A Bedienungsanleitung

Honeywell

Honeywell T2798I2000 Bedienungsanleitung

Honeywell

Honeywell WV8860C Bedienungsanleitung

Honeywell

Honeywell HC900 Betriebsanleitung

Honeywell

Honeywell CENTRA LINE MERLIN NX Series Bedienungsanleitung

Honeywell

Honeywell DCP 250 Installationsanleitung

Honeywell

Honeywell PW6K1ICE Bedienerhandbuch

Honeywell

Honeywell S7014A Series Bedienungsanleitung

Honeywell

Honeywell UDC3300 Bedienungsanleitung

Honeywell

Honeywell HR 10 F Bedienungsanleitung

Honeywell

Honeywell CIPer 50 Installations- und Betriebshandbuch

Honeywell

Honeywell AutoRAE 2 Bedienungsanleitung

Honeywell

Honeywell T775R 2000 Series Bedienungsanleitung

Honeywell

Honeywell UDC 1000 Micro-Pro Bedienungsanleitung

Honeywell

Honeywell 7800 SERIES RM7895A Bedienungsanleitung

Honeywell

Honeywell ML6161 Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch