Honeywell HC900 Gebrauchs- und Pflegehandbuch

1/2018 Controller CPU and Scanner Module Kit # 51-52-33-126 1

ControlEdge HC900 Controller

Controller CPU and Scanner Module

Installation and Replacement

Controller CPU 900C50/900C50S - (current revision number)

Controller CPU 900C30/900C30S - (current revision number)

Controller CPU 900C70/900C70S - (current revision number)

Scanner 1 900S50/900S50S - (current revision number)

Scanner 2 (for redundant controller) 900S75/900S75S - (current revision number)

Document Number Form: 51-52-33-126

Effective Date: 1/2018

Supersedes: 9/2013

Summary Enclosed is a new Controller CPU, Scanner 1, or Scanner 2 module for your

ControlEdge HC900 Controller. Use the following procedures to install or

replace a module.

Controller CPU Table 1 and 3

Scanner 1 Table 2 and 3

Scanner 2 Table 4

Although it is best practice to remove power when replacing modules, the

ControlEdge HC900 CPU and Scanner modules may be removed and inserted under power.

See the ControlEdge HC900 Controller Installation and User’s Guide for more information.

ControlEdge HC900 Hardware Controller

Rack Assembly

1. Rack, available in 4- 8-, or 12-slot versions

2. Power Supply

3. Controller CPU or Scanner 1 Module

(for Scanner 2, see Figure 4)

4. Grounding bars (for I/O wiring; optional)

5. Input/Output modules

6. I/O Terminal Blocks

Figure 1

WARNING

2 Controller CPU and Scanner Module Kit # 51-52-33-126 1/2018

Contents

Each Controller CPU and Scanner module is supplied in a shipping container and static protective

shipping bag. For protection, leave the modules in their shipping containers until ready for installation.

Each container has a label identifying the contents.

C30 Controller

C50 Controller

C70 Controller

Scanner 1 Port

(S50)

Scanner 2 Port

(S75)

Safety C30S

Controller

Safety C50S

Controller

Safety C70S

Controller

Safety Scanner 1

Port (S50S)

Safety Scanner 2

Port (S75S)

Installation Guidelines

The Controller CPU and Scanner modules may only be inserted into a dedicated slot location in the

rack. The modules are labeled on the LEFT side of the module: for example, C30, C50, C70, Scanner

1 Port (S50), Scanner 2 Port (S75) and Safety versions C30S, C50S, C70S, C75S, Scanner 1 Port

(S50S), Scanner2 Port (S75S).

Most of the components in an I/O expansion rack are identical to those used in the Controller Rack.

The Controller CPU is installed in the controller rack (Figure 1, item 3) whereas the Scanner 1 or

Scanner 2 is installed in the I/O expansion rack (Figure 2).

1/2018 Controller CPU and Scanner Module Kit # 51-52-33-126 3

Controller CPU Installation Procedure

Follow the procedure in Table 1 to install a Controller CPU module in a controller rack.

Table 1 –Controller CPU Installation

Step

Action

Orient the controller rack to have the open side of the enclosure facing forward

with the power supply module located on the left and I/O module slots on the

right (See

Remove the Controller CPU module from its shipping container.

On the new CPU set/verify serial port switch settings.

Only one port may be a Modbus Master. It can be assigned to either port.

A small slotted screwdriver or paperclip works well; avoid using pencils because

their residue can damage the switch.

SW3

Insert the module into the dedicated slot location in the rack adjacent to the

power supply. Orient the module with module name at top. Align the module

printed circuit board with the card guide slots in the chassis. Press the CPU

module into the slot until the rear connector engages the mating connector of the

rack backplane. (See Figure 2)

Figure 2

Secure the Controller CPU module top and bottom with the captive mounting

screws. Torque settings 0,4 - 0,5 Nm (3.5 –4.4 Lb-In.)

Do not install the battery at this time. See instructions in the Controller

Installation and User’s Guide (document #51-52-25-154) for additional Controller

CPU setup information and battery installation.

4 Controller CPU and Scanner Module Kit # 51-52-33-126 1/2018

Follow the procedure in Table 2 to install a Scanner 1 module in an expansion I/O rack.

Table 2 Scanner 1 Installation

Step

Action

Orient the I/O expansion rack to have the open side of the enclosure facing forward

with the power supply module located on the left and I/O module slots on the right (See

Remove the Scanner 1 module from the shipping container. Set scanner address for

the I/O rack using the switches on SW3. A small slotted screwdriver or paperclip works

well; avoid using pencils since the residue can damage the switch.

Switches 5, 6, 7, 8 must be OFF.

Only 1 switch position may be ON.

Switch 1 ON = Scanner 1

Switch 2 ON = Scanner 2

Switch 3 ON = Scanner 3

Switch 4 ON = Scanner 4

Figure 3 shows setting for Rack 2

12 3 45 6 78

SW3

12345678

SW3

Honeywell

Figure 3 - Scanner 1 switch

Insert the module into its dedicated slot location in the rack adjacent to the power

supply. Orient the module with the module name on the left side. Align the module

printed circuit board with the card guide slots in the chassis. Press the Scanner

module into the slot until the rear connector engages the mating connector of the rack

backplane. (See Figure 2)

Secure the Scanner module top and bottom with the captive mounting screws.

Torque settings 0,4 - 0,5 Nm (3.5 –4.4 Lb-In.)

1/2018 Controller CPU and Scanner Module Kit # 51-52-33-126 5

Controller CPU or Scanner 1 Replacement

Follow the procedure in Table 3 to replace a Controller CPU or Scanner 1 module in an existing rack.

Table 3 Controller or Scanner Module replacement

Step

Action

Before replacing the Controller CPU module verify a copy of the current configuration

file is available and a method of loading the file is understood. See Process Control

Designer User’s Guide or ControlEdge HC900 Control Station User’s Guide.

Remove power from the rack. (recommended)

Remove the screws that secure the module assembly to the rack.

Pull the assembly to remove. For Controller CPU modules, go to step 6.

Remove the Scanner 1 module from the shipping container.

Note: Verify module faceplate colour (Blue or Orange) matches the original faceplate.

Set scanner address for the I/O rack using the switches on SW3. A small slotted

screwdriver or paperclip works well; avoid using pencils since the residue can

damage the switch.

switches 5, 6, 7, 8 must be OFF.

Only 1 switch position may be ON.

Switch 1 ON = Scanner 1

Switch 2 ON = Scanner 2

Switch 3 ON = Scanner 3

Switch 4 ON = Scanner 4

Image shows setting for Rack 2

12 3 4 5 67 8

SW3

1234 56 78

SW3

Honeywell

Scanner 1 switch

On the new CPU set/verify serial port switch settings. See Table 1 Step 3.

Insert the new module into the dedicated slot location in the rack. Orient the module

with module name on the left side. Align the module printed circuit board with the card

guide slots in the chassis. Press the module into the slot until the rear connector

engages the mating connector of the rack backplane. (See Figure 2)

Secure the module top and bottom with the captive mounting screws.

Torque settings 0,4 - 0,5 Nm (3.5 –4.4 Lb-In.)

Re-apply power to the rack.

See instructions in the Controller Installation and User’s Guide

(document #51-52-25-154) for additional Controller CPU setup information and

battery installation.

6 Controller CPU and Scanner Module Kit # 51-52-33-126 1/2018

Scanner 2 Overview

•One Scanner2 Module is installed in

each I/O Rack of a redundant system.

•I/O ports A –connects to CPU-A and

I/O Port B connects to CPU-B of the

redundant C75 Controller CPUs.

•Maintains communications with both

Lead and Reserve C75 CPU’s to

facilitate failover.

•Reads inputs from modules in rack &

writes outputs to modules in rack.

•Required for interface to C75

redundant controllers (cannot use

Scanner1 module with C75’s nor can

Safety be used with Non-Safety).

•May be replaced under power.

•Cannot use with non-redundant

systems.

Scanner 2 Non-Safety Scanner 2 Safety

Scanner 2 Installation Guidelines

The Scanner 2 module may only be inserted into a dedicated slot location in a Remote I/O Rack.

(Figure 4)

Figure 4

Power

Supply

Power

Status

Module

Power

Supply

Dual Port

Scanner

For C75 CPU

Input/Output Modules

8 slot and 12 slot I/O Racks

1/2018 Controller CPU and Scanner Module Kit # 51-52-33-126 7

Scanner 2 Installation or Replacement

Follow the procedure in Table 4 to install or replace a Scanner 2 module in a redundant power rack.

Table 4 Scanner 2 Module installation or replacement

Step

Action

If you are installing a new Scanner 2, go to step 6.

If you are replacing the Scanner 2, go to step 2.

Remove power from the rack containing the Scanner 2 module to be replaced.

(recommended)

Remove the screws that secure the module assembly to the rack. Disconnect the A

and B IO cables noting cable to port assignment

Pull the Scanner 2 module to remove.

Remove the Scanner 2 module from the shipping container. Note: Verify module

faceplate colour (Blue or Orange) matches the original faceplate.

Position the scanner address switches on the module for the appropriate address

position (see Step 6).

Set rack address for the I/O rack using

the Scanner 2 Module switches on SW3

(shown at right).

(Scanner Address = 1 is shown.)

Switches 6-8 must be OFF.

Only 1 switch position may be ON.

Switch 1 ON = Scanner 1

Switch 2 ON = Scanner 2

Switch 3 ON = Scanner 3

Switch 4 ON = Scanner 4

Switch 5 ON = Scanner 5

A small slotted screwdriver or paperclip

works well; avoid pencils.

Insert the new module into the dedicated slot location in the rack. Orient the module

with the I/O ports on the bottom. Align the module printed circuit board with the card

guide slots in the chassis. Press the Scanner 2 module into the slot until the rear

connector engages the mating connector of the rack backplane.

Secure the new Scanner 2 module top and bottom with the captive mounting screws.

Torque settings 0,4 - 0,5 Nm (3.5 –4.4 Lb-In.)

Re-apply power to the rack.

For more information

To learn more about SmartLine Transmitters,

visit www.honeywellprocess.com

Or contact your Honeywell Account Manager

Process Solutions

Honeywell

1250 W Sam Houston Pkwy S

Houston, TX 77042

Honeywell Control Systems Ltd

Honeywell House, Skimped Hill Lane

Bracknell, England, RG12 1EB

51-52-33-126

January 2018

2018 Honeywell International Inc.

Shanghai City Centre, 100 Jungi Road

Shanghai, China 20061

www.honeywellprocess.com

Sales and Service

For application assistance, current specifications, pricing, or name of the nearest Authorized Distributor, contact one

of the offices below.

ASIA PACIFIC

Honeywell Process Solutions,

(TAC) hfs-tac-

support@honeywell.com

Australia

Honeywell Limited

Phone: +(61) 7-3846 1255

FAX: +(61) 7-3840 6481

Toll Free 1300-36-39-36

Toll Free Fax:

1300-36-04-70

China –PRC - Shanghai

Honeywell China Inc.

Phone: (86-21) 5257-4568

Fax: (86-21) 6237-2826

Singapore

Honeywell Pte Ltd.

Phone: +(65) 6580 3278

Fax: +(65) 6445-3033

South Korea

Honeywell Korea Co Ltd

Phone: +(822) 799 6114

Fax: +(822) 792 9015

EMEA

Honeywell Process Solutions,

Phone: + 80012026455 or

+44 (0)1344 656000

Email: (Sales)

FP-Sales-A[email protected]

(TAC)

hfs-tac-support@honeywell.com

AMERICA’S

Honeywell Process Solutions,

Phone: (TAC) 1-800-423-9883 or

215/641-3610

(Sales) 1-800-343-0228

Email: (Sales)

FP-Sales-A[email protected]

(TAC)

hfs-tac-support@honeywell.com

Andere Handbücher für HC900

Andere Honeywell Controller Handbücher

Honeywell

Honeywell VS820A Bedienungsanleitung

Honeywell

Honeywell VMM Series Bedienungsanleitung

Honeywell

Honeywell AQ251 Installationsanleitung

Honeywell

Honeywell 191238-ZCS Bedienungsanleitung

Honeywell

Honeywell S4965V3250 Bedienungs- und Montageanleitung

Honeywell

Honeywell ML7999A Bedienungsanleitung

Honeywell

Honeywell epc T5068A Bedienungsanleitung

Honeywell

Honeywell DCP301 Bedienungsanleitung

Honeywell

Honeywell CIPer 50 Installations- und Betriebshandbuch

Honeywell

Honeywell UDC3300 Bedienungsanleitung

Honeywell

Honeywell L4188 Bedienungsanleitung

Honeywell

Honeywell McDonald's HEMS II Bedienungsanleitung

Honeywell

Honeywell DCP 250 Installationsanleitung

Honeywell

Honeywell T2798I2000 Bedienungsanleitung

Honeywell

Honeywell ML7999C Bedienungsanleitung

Honeywell

Honeywell UDC 2300 Bedienungsanleitung

Honeywell

Honeywell Novar ES3.S Programmierhandbuch

Honeywell

Honeywell UDC3500 Bedienungsanleitung

Honeywell

Honeywell Excel 15 W7760A Bedienungsanleitung

Honeywell

Honeywell MIWI350 Betriebsanleitung

Honeywell

Honeywell GENT Mimic LED Driver Card Gebrauchsanweisung

Honeywell

Honeywell SLATE Series Bedienungsanleitung

Honeywell

Honeywell touchpoint Pro Bedienungsanleitung

Honeywell

Honeywell Evohome Gebrauchsanweisung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch