Honeywell Ex-Or MLS2000DALIHBW Installations- und Betriebshandbuch

Installation and Commissioning

Instructions

Note: HP2000 required for commissioning

HC5 or HC6 required for user override

Mid-Bay: MLS2000DIMBW for DSI ballasts

MLS2000DALIMBW for DALI ballasts

Hi-Bay: MLS2000DIHBW for DSI ballasts

MLS2000DALIHBW for DALI ballasts

MLS Digital Mid-Bay & Hi-Bay Luminaire Controllers

Red - Live

Blue - Neutral

Yellow

Green

White - MLS Bus +ve

Black - MLS Bus -ve

Electrical Connections

Polarity-free

digital output

Connection to ballast only.

Do not connect to other detectors.

750mm

lead

26mm

32.5mm

6.5mm

43.5mm sq

50mm sq

Only suitably qualified personnel should install this equipment.

Installation

Snap-in to infill panel (max 0.7mm/ 22 SWG) or use any combination of fixing holes on rear. Use only No 4

type B ºinch self-tapping screws. Ensure that projection of screws into pilot holes does not exceed 4.5mm.

The recommended position for the detector is in the middle of the luminaire. Where this is not possible and the

detector is fitted near one end of the lamps, please ensure that the detector is at the ‘cold’ end of the lamps.

In order to achieve satisfactory light-level regulating operation, a detector must observe a substantially greater

proportion of artificial light from the luminaire(s) under its control than from neighbouring luminaires not under its

control. This is particularly important when planning the installed layout of linear luminaires that have an

integral detector positioned at one end.

To Test Luminaire Controller Operation

Once the Luminaire Controllers have been installed within the luminaires, the HC5 or HC6 may be used to

switch luminaires ON and OFF. Luminaires with regulating ballasts will also dim and brighten.

Mounting Details

Cable entry point

14.5mm

20.3mm

MLS Digital Mid-Bay & Hi-Bay Luminaire Controllers

Commissioning Detectors using the HP2000

It is important that the HP2000 be held perpendicular and at a distance of between 0.5m and 2m from the detector.

1. Switch on HP2000 by pressing the red power button.

2. Point HP2000 at detector and press the DOWNLOAD button. The HP2000 will confirm the product’s identity,

and call up the correct menu of parameters and their current settings. It will also show the ballast type and the

duration (shown in hours) remaining on the 100-hour burn-in.

3. Use a combination of UP, DOWN, FORWARD and BACK buttons to navigate the parameter menu, selecting

options for each shown. (See Tips below.)

4. When options for all parameters have been selected, point the HP2000 at the detector and press the UPLOAD

button. The luminaire(s) will switch off briefly during the programming process and the HP2000 shows DATA

OK to confirm operation.

5. After a short period of inactivity (default 5 minutes), the HP2000 hibernates retaining the most recent settings.

Tips

i) Where there are only two options such as ON/OFF, a double click of the OK button toggles between them.

ii) Where there are multiple options, a double click of the OK button recalls a list of all options for that parameter.

Use the UP, DOWN and OK buttons to select.

iii) Use the OK button to go forward (through the menus) without displaying help pages.

iv) Press UPLOAD at any time to transfer all current settings from the handset to the product.

Please refer to HP2000 instructions for comprehensive commissioning details.

Factory Default Settings

These are the settings to which the units have been programmed before they leave the factory:

Parameter Options Default

Power Up On / Off On

Response Auto, Manual/Bus, Manual Auto

Off Delay 1 min - 96 hrs, 10-sec (walk-test), Disabled 20 mins

On Sensitivity 0-100 100

Bus Connect Yes / No Yes

Zones 1-4 Address 1-100 -- (no zone)

Corridor 1-2: Begin 1-100 Building Address Span -- (no zone)

Corridor 1-2: End 1-100 Building Address Span -- (no zone)

Global 1-2 Rx Yes / No No

Start Lamps Max / Min Max

Entry Scene 1-6 1

Bright Out Yes / No No

Dimming Reg 50%-Reg100% Reg 100%

Lamp Max 10%-100% 100%

Fade to Off Yes / No No

When Vacant 10 Exit Scenes Off

Set-Point High 0-1023 1023

Set-Point Low 0-1023 1023

100 Hour Burn-In See Application Note: AN4028 0 hr

Additional feature accessible under Utilities:

W5101A

Technical Data

MLS CABLE: 1.5mm unscreened twisted pair : see Application Note AN4001

OPERATING VOLTAGE: 230V 50Hz (UK & Europe)

CAPACITY: Digital DSI - 4 ballasts max

DALI - 1 ballast max

WEIGHT: 50g

COLOUR: White bezel

MATERIAL: Flame retardant PC/ABS

IP RATING: 4X

o o

OPERATING TEMPERATURE: 0 C to 55 C

At the end of their useful life

the packaging and product

should be disposed of via a

suitable recycling centre.

Do not dispose of with normal

household waste.

Do not burn.

Ex-Or

Novar ED&S LImited

Haydock Lane, Haydock, Merseyside WA11 9UJ

Tel: +44 (0)1942 719229

Fax: +44 (0)1942 508753

Email: technicalsales.ex-or@honeywell.com

www.ex-or.com

Important Additional Notes

1. Ameans for disconnection must be incorporated in the fixed wiring in accordance with the current wiring regulations.

2. Although nominally 12V, the dimming output is not SELV and therefore should be treated with the same respect as mains

with regard to wiring practice. The 0V line of the dimming output is almost at Neutral potential.

3. The dimming control output should be connected only to the control input of the ballasts - never to other detectors.

4. This equipment should be used to control only those ballasts powered from the same phase as the detector.

5. Do not connect mains to the MLS bus.

6. It is imperative that the MLS bus is wired with the correct type of cable; normally it should be 1.5mm unscreened twisted pair.

Please readApplication NoteAN4001 for more details.

7. Due to the fact that the photocell is on the ceiling looking down, it is not possible for measurements made with a lux meter on

the working plane to remain constant when daylight illuminates the ceiling and the working plane to a differing extent.

Therefore, products of this type should be regarded as capable of maintaining anAPPROXIMATE light level only.

8. This equipment switches lights no more frequently than would a responsible human occupant. However, manufacturers of

some particular lighting types (e.g. ‘2D’luminaires) may specify a maximum number of switching cycles in order to achieve a

predicted lamp life. Please check with the manufacturer of the luminaires to ensure that they are compatible with automatic

controls in this respect.

Mid-Bay:

MOUNTING HEIGHT: 12.0m max

RANGE: Cone-shaped detection pattern,

diameter at floor level (d) = 1.75 x mounting height (h)

Hi-Bay:

MOUNTING HEIGHT: 16.0m max

RANGE: Cone-shaped detection pattern,

diameter at floor level (d) = 1 x mounting height (h)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Controller Handbücher

Honeywell

Honeywell BACnet Bedienungsanleitung

Honeywell

Honeywell EDC 200 Series Bedienungsanleitung

Honeywell

Honeywell V9055A Bedienungsanleitung

Honeywell

Honeywell ML6984 Bedienungsanleitung

Honeywell

Honeywell TPPL Modbus TCP Montageanleitung

Honeywell

Honeywell Evohome Bedienungsanleitung

Honeywell

Honeywell Sieger System 57 Bedienungsanleitung

Honeywell

Honeywell VR4305 Bedienungsanleitung

Honeywell

Honeywell T775A/B/M 2000 Series Bedienungsanleitung

Honeywell

Honeywell WV8860C Bedienungsanleitung

Honeywell

Honeywell Excel 10 W7752D Bedienungsanleitung

Honeywell

Honeywell S05 Series Bedienungsanleitung

Honeywell

Honeywell T775 Series Benutzerhandbuch

Honeywell

Honeywell Vista Automation Module Bedienungsanleitung

Honeywell

Honeywell V9055A Bedienungsanleitung

Honeywell

Honeywell DC1000 SERIES Bedienungsanleitung

Honeywell

Honeywell VaporStat L408J Bedienungsanleitung

Honeywell

Honeywell AQUASTAT L4188A Bedienungsanleitung

Honeywell

Honeywell N05010 Bedienungsanleitung

Honeywell

Honeywell Excel Web XL1000A Bedienungsanleitung

Honeywell

Honeywell ML7430E Bedienungsanleitung

Honeywell

Honeywell Lyric Gebrauchsanweisung

Honeywell

Honeywell TRADELINE SV9501 Bedienungsanleitung

Honeywell

Honeywell THR0924 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch