Honeywell LT-32 Bedienungsanleitung

Fire Alarm Control Panel LT

-32 / LT-159

Quick Start Guide

-168.2-EN / 07.2022

Honeywell

MORLEY IAS Fire Systems

Support@honeywell.com

www.honeywell.com

Technical changes reserved!

Morley LT-32 Morley LT-159 Panel Installation - Three Steps Process Cable Entries Field Cable Entry

STEP 1

According to the figure, mark

the required hole on the wall.

STEP 2

All fixing point must be used.

Use 50 mm long x 5 mm diameter

screws to secure the backbox on the

wall.

•Upper and lower cable entry for 15 mm gland

•Side entry: 3 on each side (21 x 21 mm easy access)

•Central entry prepared for 60 mm universal flush box

Remove the keyholes and pass

the cables through them.

Power supply and batteries are required for commissioning!

STEP 3

Align the screws on the cover with the keyhole on the back box and lock

the cover onto the backbox.

System Setup and Cabling

Alarm and Fault Relay

Move the Jumper to Setup NO or

NC relay functionality.

Sounder circuit

End of line diode cathode marker on

positive terminal.

LT-32 Ref. Description LT-159 Ref. Description

1Fault NO/NC

Fault C

Alarm NO/NC

4Alarm C 4Alarm C

Loop A +

Loop A -

7Sounder 2 + 7Loop B +

Sounder 2 -

Loop B -

Sounder 1 +

10 Sounder 1 -10 Sounder 1 -

11 Power + 11

Power +

Power -

Panel Connection

Highlighted the differences between panel LT-32 and LT-159.

Battery Connection

Batteries connected in two rows 

with polarity as shown.

Additional and updated Informations

The described features, specifications and product related informations in this manual correspond to the date of issue (refer to date on the front page) and may differ due to modifications and/or amended Standards and

Regulations of the System design, Installation and Commissioning.

For further Informations refer to documentation M-168.1-SERIE-LT-EN.

Panels Display Controls, Buttons and Password Quick Programming Procedure with Default General Alarm Functionality

STATUS ICON

CONDITION /

CONTROL

COLOR DESCRIPTION

FIRE

Red (blinking)

A fire condition has been detected (buzzer active)

Red (fixed)

The user has acknowledged the event by buzzer silence

SYSTEM FAULT Yellow (fixed) System fault

GENERAL FAULT

Yellow (blinking)

General fault, buzzer is active

Yellow (fixed) The user has acknowledged the event by buzzer silence

DISABLE Yellow (blinking) A device or zone is disabled

TEST Yellow (blinking) A zone is in test mode

SOUNDER SILENCE

Yellow (blinking)

The internal buzzer is silenced

Yellow (fixed)

The sounders are silenced

POWER FAULT

(from 100 … 230 Vac

or batteries)

Yellow (blinking)

Mains fault

Yellow (fixed) Batteries fault

POWER Green (fixed) The system is switched on and the power is supplied via the mains

1. On the touch screen display press the arrow on the right and then press the gear icon at the top right:

2. Insert password level 2, press enter then press on program icon, insert password level 3 and press enter to confirm.

3. Select Panel configuration to change the language using the arrow down icon.

Once completed, press the left arrow to come back to the previous screen.

4. Select Autoprog, press the Lens icon to search for devices, at the end of the process save devices detected with

check mark. Press the left arrow to come back to the previous screen.

5. Select Description to change both Zone and Point labels. This example refers to Zones: Press Zone icon, type the

label using the virtual keyboard and confirm with enter. Same applies to Points.

6. Come back to Configuration menu using the left arrow and set Date and Time. The example shares how to change

Date: select Date icon, scroll up and down the day, month and year values then confirm with check mark. To change

Time, follow the same process.

PUSH

BUTTON

DESCRIPTION FUNCTION

RESET PANEL Pressing the ‘Reset Panel’ button will reset the panel to return it to normal condition after an event

MUTE Pressing the ‘Mute’ button or tapping on the touch screen, will silence the active panel buzzer

SILENCE SOUNDERS Pressing the ‘Silence Sounders’ button will silence all Alarm sounders

EVACUATE

Pressing the ‘Evacuate’ button and later confirm the evacuation in the pop-up window, will start

all the panel sounders output activation and the output configured for evacuation in the Cause

and Effect I/O Matrix

FUNCTION

EN 54 LEVEL

FACTORY DEFAULT PASSWORD

Alarm, disabled, and faults display

Level 1

None

Alarm and faults recognition

Level 1

None

Disabled Zone/Point display

Level 1

None

Enable/Disable menu

Level 2

2222

Test menu

Level 2

2222

Utility menu

Level 2

2222

Programming menu

Level 3

33333333

Andere Handbücher für LT-32

Dieses Handbuch passt für folgende Modelle

Andere Honeywell Controller Handbücher

Honeywell

Honeywell SUPER TRADELINE S8610U Bedienungsanleitung

Honeywell

Honeywell MS4120S Bedienungsanleitung

Honeywell

Honeywell TRADELINE SmartValve SV9602P Bedienungsanleitung

Honeywell

Honeywell UDC120L Bedienungsanleitung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Honeywell

Honeywell SEC-H-602 Bedienungsanleitung

Honeywell

Honeywell PW6K1ICE Bedienerhandbuch

Honeywell

Honeywell HON R100NG Series Betriebsanleitung

Honeywell

Honeywell Scan Dome ll HTX-2500 Betriebsanleitung

Honeywell

Honeywell UDC1200 MICRO-PRO Benutzerhandbuch

Honeywell

Honeywell MN6110 Bedienungsanleitung

Honeywell

Honeywell T775P 2000 Series Bedienungsanleitung

Honeywell

Honeywell UDC2500 Bedienungsanleitung

Honeywell

Honeywell 2RM7800L1087 Service-Handbuch

Honeywell

Honeywell S9240F2051 Bedienungsanleitung

Honeywell

Honeywell ML6874 Bedienungsanleitung

Honeywell

Honeywell V8200 Bedienungsanleitung

Honeywell

Honeywell PW-6000 Bedienerhandbuch

Honeywell

Honeywell 40014 Bedienungsanleitung

Honeywell

Honeywell WEB-700 Bedienungsanleitung

Honeywell

Honeywell H112 Bedienungsanleitung

Honeywell

Honeywell UDC 2300 Bedienungsanleitung

Honeywell

Honeywell T775 Series Benutzerhandbuch

Honeywell

Honeywell HON 5020 Betriebsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch