Honeywell Ex-Or MSM2000D Installations- und Betriebshandbuch

LightSpot Luminaire Controllers

MSM2000D/DALI - Digital Control Module

DHW/DHS - Mini Detector Head

Installation and Commissioning

Instructions

Note: QuickSet Pro (or HP18*) required for commissioning

* Please note that the HP18 offers different/limited programming options

Mounting Details

The MSM2000 Control Module is designed to be mounted within the luminaire on fixing centres of 135mm.

Connections to the control module as shown above should be made using solid strand wire (0.5-1.5mm ).

The interconnect cable between the detector head and control module should be routed away from other

luminaire internal wiring and away from the lamp end-caps.

The recommended position for the detector is in the middle of the luminaire. Where this is not possible and the

detector is fitted near on end of the lamps, please ensure that the detector is at the ‘cold’ end of the lamps.

The DHW/S Mini Detector Head should be mounted such that only the raised front section of the bezel protrudes

through the cut out in the louvre or infill panel, constructed in accordance with the dimensions above.

Installation Guidelines

1. The Mini Detector Head must be mounted within the luminaire. Do not mount remotely.

2. The connecting cable must not be extended.

3. Artificial light illuminating the Mini Detector Head must only be reflected from the room - i.e. there must be no

direct illumination.

4. In order to receive satisfactory light-level regulating operation, a detector must observe a substantially greater

proportion of artificial light from the luminaire(s) under its control than from neighbouring luminaires not under its

control. This is particularly important when planning the installed layout of linear luminaires that have an integral

detector positioned at one end.

Neutral

OneSwitch Input

N/C

Live IN

}

Polarity-free

Digital Output

Neutral

Live IN

}

Digital Regulating Ballast(s)

MSM2000D

OneSwitch Input

for manual control

Mains Supply

Polarity-free

Digital Input

Analogue 1-10V

Control Module

Electrical Connections

800mm

Flying Lead RJ12

Plug

14.9mm

21.5mm

TOP VIEW

SIDE VIEW

32mm

21.5mm

18.8mm

17.5mm

21.3mm

Mini Detector

Head

147.5mm

135mm

(Height = 22mm)

30mm

Operating voltage 230V~50Hz±10%

Control output: Digital

Max 4 x DSI or 4 x DALI Ballast

Power consumption: <2W

tc 70 C

Control Module Part No

MLSM2000D MKII

MSM2000D MKII

MLSM2000DALI MKII

MSM2000DALI MKII

by Honeywell

Ex-Or Limited

St. Mark’s Court,

North Street,

Horsham,

RH12 1BW

www.ex-or.com

Please read instructions prior to installation

Detector

Connection

MLS Bus

Polarity Free

Made in UK

Neutral

OneSwitch Input

N/C

Live IN

}

0.5 - 1.5

Polarity-free

Digital Output

Commissioning

Detectors are supplied factory pre-set which ensures the lighting will switch on automatically as soon as power

is applied. Final commissioning of the detectors requires the use of an infrared Programmer. The QuickSet Pro

gives access to the full range of parameters and options but limited programming functions can also be carried

out using an HP18.

Commissioning Detectors using the QuickSet Pro Programmer

It is important that the Programmer be held perpendicular between 0.5m and 2m from the sensor.

1. Switch on by pressing any button (and unlock with top left rectangular button).

2. Point the programmer at detector and press the DOWNLOAD button. The programmer will confirm the

product’s identity and call up the correct menu of parameters and their current settings.

3. Use a combination of UP, DOWN, FORWARD and BACK buttons to navigate the parameter menu,

selecting options for each shown.

4. When options for all parameters have been selected, point the programmer at the detector and press the

UPLOAD button. The luminaire(s) will switch off briefly during the programming process.

5. After a short period of inactivity (default 5 minutes), the programmer hibernates retaining the most recent

settings.

OneSwitch Dimming

OneSwitch dimming affords local control to the end-user whereby a simple, momentary, push-to-make wall

switch can be used to raise or lower the lighting level or to toggle the output ON/OFF. A press of less than

1 second will toggle the output status while a longer press will raise or lower the output. Each time the switch is

pressed, the direction of dimming reverses. If the switch has not been pressed for 5 seconds, the direction will

be up (brighter) - unless the output is already above 90% (dc 8V) in which case the direction is down.

To Test with Hand-held Controller

Once the LightSpot Luminaire Controllers have been installed within the luminaires, a Hand-held Controller or

Programmer (HC5A or HP18) may be used to dim and brighten luminaires and to switch them ON and OFF.

NB: See also ‘Important Additional Notes’ overleaf.

W4267I

Technical Data

MAXIMUM RECOMMENDED MOUNTING HEIGHT: 3.0m

RANGE: Cone-shaped detection pattern, diameter (at floor level) = 2.4 x mounting height

OPERATING VOLTAGE: 230V 50Hz (UK & Europe)

ta = 0 - 50 C

CAPACITY: Max 4 x DSI or DALI ballasts

INTERCONNECT CABLE TEMPERATURE RATING: 60 C

COLOUR: White (RAL9010) or silver bezel (DHW = White, DHS = Silver)

MATERIAL: UV stabilised polycarbonate (DHW/DHS)

Flame retardant PC/ABS (MSM2000D/DALI)

IP RATING: 20

DIMENSIONS: 32 (l) x 21 (w) x 18.6 (h) mm (DHW/DHS)

147 (l) x 30 (w) x 21 (h) mm (MSM2000D/DALI)

WEIGHT: 32g incl. 0.8m cable (DHW/DHS)

48g (MSM2000D/DALI)

6.0m

2.5m

Important Additional Notes

1. A means for disconnection must be incorporated in the fixed wiring in accordance with the current wiring regulations.

2. Although nominally 12V, the dimming output is not SELV and therefore should be treated with the same respect as mains

with regard to wiring practice. The 0V line of the dimming output is almost at Neutral potential.

3. The dimming control output should be connected only to the control input of the ballasts - never to other detectors.

4. This equipment should be used to control only those ballasts powered from the same phase as the detector.

5. Due to the fact that the photocell is on the ceiling looking down, it is not possible for measurements made with a lux meter on

the working plane to remain constant when daylight illuminates the ceiling and the working plane to a differing extent.

Therefore, products of this type should be regarded as capable of maintaining an APPROXIMATE light level only.

6. This equipment switches lights no more frequently than would a responsible human occupant. However, manufacturers of

some particular lighting types (e.g. ‘2D’ luminaires) may specify a maximum number of switching cycles in order to achieve a

predicted lamp life. Please check with the manufacturer of the luminaires to ensure that they are compatible with automatic

controls in this respect.

7. Some devices in this product range feature a silvered surface finish; this is intended for decorative purposes only. Care

should be taken to avoid accidental separation of the silvered coating from the product. If the unit is built into a luminaire

that is subsequently wrapped in film having adhesive properties, it is recommended that a layer of suitable packaging

material be used to protect the silvered area.

Honeywell Ex-Or

St. Marks Court, North Street, Horsham,

West Sussex, RH12 1BW, UK.

Tel: +44 (0)1942 719229

Email: ex-ortechnicalsales@honeywell.com

www.ex-or.com

At the end of their useful life

the packaging and product

should be disposed of via a

suitable recycling centre.

Do not dispose of with normal

household waste.

Do not burn.

Dieses Handbuch passt für folgende Modelle

Andere Honeywell Controller Handbücher

Honeywell

Honeywell S9361A207 Series Bedienungsanleitung

Honeywell

Honeywell AQUASTATIC L7224 Series Bedienungsanleitung

Honeywell

Honeywell Touchpoint Plus Versionshinweis

Honeywell

Honeywell Experion 8 Series Handbuch

Honeywell

Honeywell FR124 Bedienungsanleitung

Honeywell

Honeywell Pneumatic Controls Bedienungsanleitung

Honeywell

Honeywell ADEMCO Optiflex Bedienungsanleitung

Honeywell

Honeywell S9201A1010 Bedienungsanleitung

Honeywell

Honeywell HR 80 Bedienungsanleitung

Honeywell

Honeywell VBN2 Bedienungsanleitung

Honeywell

Honeywell HR92UK Bedienungsanleitung

Honeywell

Honeywell AUTOMATIC CONTROL Installations- und Betriebshandbuch

Honeywell

Honeywell DeltaNet R7515A Bedienungsanleitung

Honeywell

Honeywell T775 Series Benutzerhandbuch

Honeywell

Honeywell HVC0001 Bedienungsanleitung

Honeywell

Honeywell HVC0001 Bedienungsanleitung

Honeywell

Honeywell CENTRA LINE MERLIN N Series Bedienungsanleitung

Honeywell

Honeywell AQS51-KAM Bedienungsanleitung

Honeywell

Honeywell S05 Series Bedienungsanleitung

Honeywell

Honeywell ML6421 Bedienungsanleitung

Honeywell

Honeywell MN7220 Bedienungsanleitung

Honeywell

Honeywell Spyder BACnet PUB1012S Bedienungsanleitung

Honeywell

Honeywell Sieger System 57 Bedienungsanleitung

Honeywell

Honeywell VK41 V Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch