Honeywell N20010 Bedienungsanleitung

® U.S. Registered Trademark EN0B-0341GE51 R0307

N20010, N34010

NON-SPRING RETURN DAMPER ACTUATOR

20/34 Nm (177/300 lb-in) FOR MODULATING CONTROL

PRODUCT DATA

GENERAL

These direct-coupled damper actuators provide modulating

control for:

•air dampers,

•VAV units,

•air handling units,

•ventilation flaps,

•louvers, and

•reliable control for air damper applications with up to

4.6 m

/ 50 sq.ft. (20 Nm / 177 lb-in) or 7.8 m

/ 85 sq. ft.

(34 Nm / 300 lb-in) (seal-less dampers; air friction-

dependent).

FEATURES

•New self-centering shaft adapter

•Access cover to facilitate connectivity

•Declutch for manual adjustment

•Mechanical end limits

•Field-installable auxiliary switches

•Rotation direction selectable by switch

•Mountable in any orientation (no IP54 if upside down)

•Mechanical position indicator

SPECIFICATIONS

Supply voltage 24 Vac ±20%, 50/60 Hz;

24 Vdc -10...+20%

Nominal voltage 24 Vac, 50/60 Hz; 24 Vdc

All values stated hereinafter apply to operation under

nominal voltage conditions.

Power consumption

N20010 6 VA / 6 W

N34010 8 VA / 6 W

Ambient limits

Ambient operating limits -20...+60 °C (-5...+140 °F)

Ambient storage limits -40...+80 °C (-40...+175 °F)

Relative humidity 5...95%, non-condensing

Safety

Protection standard IP54

Protection class II as per EN 60730-1

Overvoltage category II

Lifetime

Full strokes 60000

Repositions 1.5 million

Mounting

Round damper shaft 10...27 mm (3/8...1-1/16")

Square damper shaft 10...18 mm (3/8...11/16");

45° steps

Shaft length min. 22 mm (7/8")

Control signal 0(2)...10 Vdc

0(4)...20 mA

Input impedance 100 kΩ[0...10 V]

500 Ωm [0...20 mA]

Feedback signal

Limits ±1 mA at 0...10 V

End switches (when included)

Rating 5 A (resistive) / 3 A (inductive)

Triggering points 5°/ 85°

Torque rating

N20010 20 Nm (177 lb-in)

N34010 34 Nm (300 lb-in)

Runtime 95 sec (60 Hz) / 110 sec (50 Hz)

Rotation stroke 95°±3°

Dimensions see "Dimensions" on page 8

Weight (without cables) 1.35 kg (3 lbs.)

Noise rating 45 dB(A) max. at 1 m

Software Class A as per EN 60730-1

SmartAct N20010, N34010

EN0B-0341GE51 R0307 2

MODELS

order number supply voltage end switches control signal feedback torque

N20010 24 Vac -- 0...10 Vdc / 0...20 mA 0...10 Vdc 20 Nm (177 lb-in)

N20010-SW2 24 Vac 2 0...10 Vdc / 0...20 mA 0...10 Vdc 20 Nm (177 lb-in)

N34010 24 Vac -- 0...10 Vdc / 0...20 mA 0...10 Vdc 34 Nm (300 lb-in)

Product Identification System

SmartAct

20X

N = non-spring return

S = spring return

20 = 20 Nm (177 lb-in)

34 = 34 Nm (300 lb-in)

010 = modulating

24 = 24 V floating+ON/OFF

230 = 230 V floating+ON/OFF

Fig. 1. Product Identification System

OPERATION / FUNCTIONS

90 90

Fig. 2. Setting units and control elements

Legend for Fig. 2:

1 Self-centering shaft adapter

2 Retainer clip

3 Rotational angle scales (0...90° / 90...0°)

4 Mechanical end limits (20 Nm [177 lb-in] models, only)

5 Declutch button

6 Anti-rotation bracket

7 Rotation direction switch

8 Access cover

Contents of Package

The delivery package includes the actuator itself, parts 1

through 8 (see Fig. 2), the anti-rotation bracket screws, and

the SM mounting plate and screws.

Modulating Control

The actuator is capable of being operated by several

controllers providing Vdc or mA output.

Rotary Movement

The control signal and the corresponding rotation direction

(clockwise or counterclockwise) can be selected using the

rotation direction switch (see part 7 in Fig. 2), thus eliminating

the need to re-wire. To ensure tight closing of the dampers,

the actuator has a total rotation stroke of 95°.

As soon as operating power is applied, the actuator may start

to run. When power is removed, the actuator remains in

position. For actuator-controller wiring instructions, see

section "Wiring" on page 5.

SmartAct N20010, N34010

3 EN0B-0341GE51 R0307

Rotation Direction Switch

Fig. 3. Rotation Direction Switch

Table 1. Feedback/control signal values

feedback/control signal when

actuator is

rotation direction

switch position totally totally

Y=2 /2...10V U = 2 V U = 10 V

Y=0 /0...10V* U = 0 V U = 10 V

Y=0 /10...0V U = 10 V U = 0 V

Y=2 /10...2V U = 10 V U = 2 V

* Default shipping position.

Feedback Signal and Manual Adjustment

If, while the actuator is not rotating, the user declutches it and

manually repositions the shaft adapter, the feedback signal

will then follow the new position at which the shaft adapter

has been left.

Power OFF/ON Behavior

In case the power to the actuator fails, after re-applying

power, the actuator aknowledges its present position and

follows the signal from the controller. This makes it

unnecessary for the actuator to employ autoadaption in order

to re-map the control signal settings.

Dip Switches

The actuators are equipped with two dip switches accessible

after removing the access cover (see Fig. 4).

voltage/current control signal

dip switch ( )

OFF

autoadapt dip switch for

normal operation ( )

Fig. 4. Dip switches (view with PCB at bottom)

Autoadapt Dip Switch for Normal Operation

In its default shipping position, the autoadapt dip switch for

normal operation is set to ON as shown in Fig. 4. If it is set to

OFF, no autoadapting is performed, and the control signal

map remains constant.

The autoadapt functionality does not have to be triggered.

Rather, the SmartAct actuator does this automatically when

the min. and max. control signals are provided (see Fig. 5);

the feedback signal is likewise autoadapted.

Fig. 5. Actuator positioning curve

Adjusting the Actuator for Autoadapt

In order to make use of the autoadapt functionality, proceed

as follows:

1. Set the autoadapt dip switch to the ON position.

2. If necessary, limit the stroke to the desired range using

the mechanical end limits.

3. Drive the actuator to the left end limit (totally counter-

clockwise) by setting the control signal as specified in

Table 1.

4. Drive the actuator to the right end limit (totally clockwise)

by setting the control signal as specified in Table 1. The

stroke has now been limited to 0...100% of the control

signal range.

Voltage/Current Control Signal Selection Dip Switch

In its default shipping position, the voltage/current control

signal dip switch (see Fig. 4) is set to OFF (= voltage control).

as shown in Fig. 4. Setting it to ON results in current control.

Position Indication

The hub adapter indicates the rotation angle position by

means of the rotational angle scales (0...90° / 90...0°).

90 90

Fig. 6. Position indication

SmartAct N20010, N34010

EN0B-0341GE51 R0307 4

Manual Adjustment

IMPORTANT

In order to prevent equipment damage, you must

remove power before manual adjustment.

After removing power, the gear train can be disengaged using

the declutch button, permitting the actuator shaft to be

manually rotated to any position. The feedback signal will

then follow the new position.

Limitation of Rotation Stroke

Two mechanical end limits (adjustable in 3° increments) are

provided (20 Nm [177 lb-in] models, only) to limit the angle of

rotation as desired (see Fig. 7).

Fig. 7. Mechanical end limits

The mechanical end limits must be securely fastened in place

as shown in Fig. 8. Specifically, it is important that they

properly mesh with the rotational angle scales when the

screws are tightened.

Fig. 8. Correct / incorrect tightening of end limits

Internal End Switches

NOTE: Only those actuators for which the option "-SW2"

has been specified when ordering (e.g.: "N20010-

SW2") feature internal end switches.

The internal end switches are set to change from "common"

to "normally open" at angles of 5° and 85°, respectively, from

the totally counterclockwise position.

5° 10° 15° 92.5°0° 90°-2.5° 85°80°75°

°7

°-2.

°1

5° 10° 15°0° 90°85°80°75°

CCW internal

end switch CW internal

end switch

actuator scale: clockwise

end switch scale

actuator scale: counterclockwise

Fig. 9. Internal end switches

Override

If terminal Y of the terminal strip (see section "Wiring

Diagrams" on page 6) is unplugged, the stroke will be 0%;

reversing the rotation direction using the rotation direction

switch will result in a max. stroke of 100%. If terminal Y is

jumped with terminal 1 (24 Vac), the stroke will be 50%.

INSTALLATION

These actuators are designed for single-point mounting.

IMPORTANT

In order to prevent equipment damage, you must

remove power or set the rotation direction switch to the

"Service/Off" position before manual operation.

Mounting Instructions

All information and steps are included in the Installation

Instructions supplied with the actuator.

Mounting Position

The actuators can be mounted in any desired orientation (no

IP54 if mounted upside down; see Fig. 10). Choose an

orientation permitting easy access to the actuator's cables

and controls.

IP54 IP54IP54 IP54

Fig. 10. Mounting for IP54

Mounting Bracket and Screws

If the actuator is to be mounted directly on a damper shaft,

use the mounting bracket and screws included in the delivery

package.

SmartAct N20010, N34010

5 EN0B-0341GE51 R0307

Self-Centering Shaft Adapter

The self-centering shaft adapter can be used for shafts

having various diameters (10...27 mm [3/8...1-1/16"]) and

shapes (square or round).

In the case of short shafts, the shaft adapter may be reversed

and mounted on the duct side.

Stroke Limitation with Mechanical End Limits

The mechanical end limits (20 Nm [177 lb-in] models, only)

enable the stroke to be limited from 0...90° in increments of

3°.

Wiring

Connecting to the Power Supply

In order to comply with protection class II, the power source of

24 V actuators must be reliably separated from the network

power supply circuits as per DIN VDE 0106, part 101.

Access cover

To facilitate wiring the actuator to the controller, the access

cover can be detached from the actuator.

IMPORTANT

Remove power before detaching the access cover.

Once the access cover has been removed, please

take care to avoid damaging any of the parts now

accessible.

Fig. 11. Access cover (N20010-SW2)

Depending upon the model, the access cover may have one

or two terminal strips, including a layout with a description for

each of the terminals.

Fig. 12. N20010-SW2 with access cover removed

SmartAct N20010, N34010

EN0B-0341GE51 R0307 6

Wiring Diagrams

N20010 / N34010

TERMINAL STRIP 1

0(2)...10 Vdc

0(4)...20 mA

0(2)...10 Vdc

MODULATING CONTROL

Connect via safety

isolating transformer!

24 Vac 24 Vdc

N20010-SW2

0(2)...10 Vdc

0(4)...20 mA

0(2)...10 Vdc

MODULATING CONTROL

Connect via safety

isolating transformer!

24 Vac 24 Vdc

END SWITCHES

TERMINAL STRIP 1

END SWITCHES

NOTE:

Internal end switches S1 and S4 must be connected to the same power source.

connecting cable terminal name

1~ 24 Vac ~ / 24 Vdc +

⊥

24 Vac ~ / 24 Vdc -

3Y 0(2)…10 Vdc / 0(4)…20 mA control signal

supply and signal lines

(must be equipped with spark suppressors)

4U 0(2)…10 V feedback signal

S1 common

S2 normally closed

CCW (left) 5°

S3 normally open

S4 common

S5 normally closed

end switches

(when included)

CW (right) 85°

S6 normally open

SmartAct N20010, N34010

7 EN0B-0341GE51 R0307

OPTIONAL ACCESSORIES

The following optional accessories can be ordered separately.

Auxiliary Switch Kit

Order no.: SW2

BS4

S6 C

The internal auxiliary switches are field-installable parts

providing two SPDT freely-adjustable switches.

Access Cover Kit

Order no.: WB20

For M20 outlets.

Contains:

•

1 access cover (with screw)

•

2 cable connectors

•

2 dust-protection caps

SPARE PARTS

Spare Parts Kit

Order no.: A7209.2071

The spare parts kit contains the following items:

•

Anti-rotation bracket and screws

•

SM Mounting plate and screws

•

Access cover screw

•

Plastic protective cap for protection standard IP54

•

Mechanical end limit screw and retainer

Anti-Rotation Bracket Kit

Order no.: A7209.2073

The anti-rotation bracket kit can be ordered separately.

Contains:

•

10 anti-rotation brackets

•

20 screws

SM Mounting Plate Kit

Order no.: A7209.2072

The SM mounting plate kit can be ordered separately.

Contains:

•

10 SM mounting plates

•

20 screws

SmartAct N20010, N34010

Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Ecublens, Route du Bois 37, Switzerland by its Authorized Representative:

Automation and Control Solutions

Honeywell GmbH

Böblinger Straße 17

D-71101 Schönaich

Phone: (49) 7031 63701

Fax: (49) 7031 637493

http://europe.hbc.honeywell.com

Subject to change without notice. Printed in Germany Manufacturing location certified to

EN0B-0341GE51 R0307

DIMENSIONS

shaft

adapter shaft

adapter (reverse)

anti-rotation bracket

100 mm (3-15/16”)

20.6 mm

(1-3/16”)

48 mm

(1-7/8”)

95°

223 mm (8-25/32”)

92 mm (3-5/8”)

1000 mm (39”)

5 mm (+0.05, -0.10 mm)

25/128” (+0.002, -0.004”)

2 mm (5/64”)

20 mm (25/32”)

13 mm (1/2”)

7 mm (9/32”)

132 mm (5-3/16”)

min. 60 mm (2-3/8”)

230 mm [+/- 0.5 mm] (9-1/16” [+/-1/64”])

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Controller Handbücher

Honeywell

Honeywell CENTRA LINE EAGLEHAWK NX Installations- und Betriebshandbuch

Honeywell

Honeywell V4055F Bedienungsanleitung

Honeywell

Honeywell DC1000 SERIES Bedienungsanleitung

Honeywell

Honeywell MO953 Series Montageanleitung

Honeywell

Honeywell MS4120S Bedienungsanleitung

Honeywell

Honeywell M6410C/L Bedienungsanleitung

Honeywell

Honeywell Lyric Produktinformationsblatt

Honeywell

Honeywell Ex-Or MSM2000D Installations- und Betriebshandbuch

Honeywell

Honeywell ZG 215N Bedienungsanleitung

Honeywell

Honeywell UMC800 Bedienungsanleitung

Honeywell

Honeywell Spyder PUL1012S Bedienungsanleitung

Honeywell

Honeywell HON 380 Bedienungsanleitung

Honeywell

Honeywell SW2 Bedienungsanleitung

Honeywell

Honeywell N05 Series Bedienungsanleitung

Honeywell

Honeywell T775 Series Benutzerhandbuch

Honeywell

Honeywell HVC0001 Bedienungsanleitung

Honeywell

Honeywell Touchpoint Plus Versionshinweis

Honeywell

Honeywell DCP301 Bedienungsanleitung

Honeywell

Honeywell touchpoint Pro Bedienungsanleitung

Honeywell

Honeywell UDC2500 Bedienungsanleitung

Honeywell

Honeywell SSW2-1M Bedienungsanleitung

Honeywell

Honeywell DCP 250 Installationsanleitung

Honeywell

Honeywell PP904A Bedienungsanleitung

Honeywell

Honeywell ControLinks R7999C Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch