Honeywell Excel 10 Bedienungsanleitung
74-3965
Excel 10
VAV II Balancing
Controllers
QUICK GUIDE
INTRODUCTION
The Honeywell Excel 10 VAV II Balancing Quick Guide
is intended to act as a on-the-job help for VAV Air
Balancers, Contractors, and Honeywell Technicians
balancing the Excel 10 VAV II family of controllers
using E-vision, LONSPEC™, or the hand-held tool. The
guide covers general troubleshooting tips, rules of
thumb, and step-by-step guides of these tools. The
guide is not intended to replace the Excel 10 VAV
software tools User Guides, but rather to act as a
supplement.
74-3965 2
TROUBLESHOOTING TIPS
Stable Airflow
When the VAV II controller is being balanced, the
configuration or balancing tool may indicate stable
airflow and allow balancing before the controller has
actually reached the balancing control setpoint. During
this period, if any measurements are made of the
actual airflow volume and entered while the controller
is still ramping to the airflow setpoint, erroneous
balancing results may be recorded.
IMPORTANT
• Excel 10 VAV II Controllers must have an air
flow pickup table downloaded to ensure
accurate balancing. Configuration tools do
not automatically install the flow pickup table
defined for the controller.
• If VAV II Controllers are not balancing, check
with the Honeywell Authorized technician or
Honeywell contractor that the flow pickup
table download to each controller has
occurred.
Testing Airflow Measurement
Anytime the controller’s airflow measurement process
is to be tested or troubleshooting is attempted, the
airflow must be constant. The VAV II controller should
be fixed at some desired or stable setpoint that is not
changed during troubleshooting or testing.
3 74-3965
Disconnecting Airflow Pickup Tubes
Anytime the airflow pickup tubes are disconnected
from the controller, the controller should be powered
down. There is no chance of damage to the controller,
but if the controller is exposed to unusually high static
pressure (< 5.0 in. w.c.) when one pickup tube is
connected there is a very slight possibility that the
controllers sensing process will stop operating. Should
this condition be suspected, simply cycle power to the
controller. It is not possible for this condition to occur
under normal operation with both airflow pickup tubes
connected to the controller.
Flow Pickup Pressure Physical
Measurement
Physical measurement of the flow pickup pressure for
the purpose of testing is best done with an instrument
capable of displaying pressure to 0.01 ±0.005 in. w.c.
Though electronic gauges and sensors often offer the
necessary accuracy, their sensitivity can cause
problems in field applications.
RULES OF THUMB
Balancing Airflow Setpoint Guidelines
All VAV II controllers must be balanced for both
minimum and maximum airflow for highest accuracy. If
the controller’s final configuration is to be a constant
volume unit, a minimum airflow balance is
recommended. The following guidelines are
recommended for flow volume setpoints.
74-3965 4
Table 1. Setpoint Guidelines.
If the guidelines outlined in Table 1 are enforced, then
most issues encountered with minimum airflow
balancing at the minimum setpoint are removed.
However, there are some symptoms that may require
minor adjustments.
Erratic or Unstable Airflow or
Zero / “Invalid” Display After Balancing
Unstable Airflow at Low Velocities
Check the damper drive parameters. If there is a rapid
cycling of the sensed airflow, when the balancing is
completed, unexpected and large air balance value
swings can occur. If this is noted, an adjustment of the
damper drive parameters may be required.
Airflow
Setpoint Rule
Maximum Maximum airflow setpoint cannot result in
a duct velocity greater than 3500 fpm
Maximum airflow setpoint must be greater
than the Minimum airflow setpoint
Minimum Minimum airflow setpoint cannot be set to
zero for balancing
Minimum airflow setpoint should be less
than or equal to 80% of the Maximum
airflow setpoint
5 74-3965
Minimum Airflow Setpoint too Close to
Maximum Airflow Setpoint
Decrease the value of the Minimum Airflow setpoint
and repeat the minimum airflow balance procedure.
Airflow Velocity Less Than 200 fpm
Check the velocity at the minimum airflow setpoint. If
the minimum airflow velocity is at or below 200 fpm, try
increasing the minimum airflow setpoint.
Airflow Sensor
If there are issues in the minimum airflow balancing,
one possible area to check is the operation of the
airflow sensor itself.
74-3965 6
BALANCING EXCEL 10 VAV II
WITH S7751A HAND-HELD TOOL
VERSION 2 (HHT2)
NOTE: Standard commissioning and Flow table
download steps must be completed before
starting this task. See S7751A Hand-Held
Tool II Product Data, Form 74-3031.
START
PLUG HHT2 INTO LONWORKS
NETWORK ACCESS LOCATION
TURN ON HHT2
SELECT HHT2 FUNCTION
SELECT "CHANGE AUTHORIZATION"
SELECT "BALANCE VAV2"
PRESS TOP MENU BUTTON
ENTER AAAA*
SELECT "EXCEL 10"
SELECT EXCEL 10 TO BE BALANCED THROUGH
ENTERING NODE #, NEURON ID, OR
IF A NON-NETWORKED CONTROLLER, USE STANDALONE ID
A
7 74-3965
STOP
SELECT "MAXIMUM"
CHECK
TROUBLESHOOTING
AND RULES OF THUMB;
MAKE CORRECTIONS
SELECT "PREVIOUS MENU"
ENTER MEASURED VALUE IN CFM AND PRESS ENTER
HAS
AIRFLOW
STABILIZED,
INDICATED BY
THE HHT2
BEEP?
YES
NO
SELECT "MINIMUM"
CHECK
TROUBLESHOOTING
AND RULES OF THUMB;
MAKE CORRECTIONS
ENTER MEASURED VALUE IN CFM AND PRESS ENTER
HAS
AIRFLOW
STABILIZED,
INDICATED BY
THE HHT2
BEEP?
YES
NO
PRESS ANY KEY THEN SELECT "BALANCE VAV2"
A
74-3965 8
BALANCING EXCEL 10 VAV II
WITH LONSPEC/VAV PLUG-IN
NOTE: The standard commissioning and flow table
download steps must be completed before
starting this task. See LONSPEC User Guide,
Form 74-2937.
LAUNCH
LONSPEC / VAV II PLUG-IN
HIGHLIGHT "HONEYWELL VAV2 CALIBRATE"
AND SELECT OK
SELECT FLOW CALIBRATION TAB ON THE
SENSOR CALIBRATION SCREEN FOR XL10 VAV2
START
A
9 74-3965
SELECT "MAXIMUM" UNDER THE ACTION WINDOW
CLICK THE "CALIBRATE" BUTTON
ENTER STABLE FLOW MEASURED VALUE
MAXIMUM AIR
BALANCE
CLICK THE "START" BUTTON
UNDER THE ACTION WINDOW
SELECT "MINIMUM"
STOP
HAS
MEASURED FLOW
BOX TURNED
WHITE?
YES
STABLE FLOW
IS NOT YET
REACHED
NO
ENTER STABLE FLOW MEASURED VALUE
MINIMUM AIR
BALANCE
CLICK THE "START" BUTTON
HAS
MEASURED FLOW
BOX TURNED
WHITE?
YES
STABLE FLOW
IS NOT YET
REACHED
NO
A
74-3965 10
BALANCING EXCEL 10 VAV II
WITH E-VISION
NOTE: The standard commissioning and Flow table
download steps must be completed before
starting this task. See E-Vision User Guide,
Form 74-2588.
DOUBLE CLICK
E-VISION
SELECT A VAV II CONTROLLER
FROM THE NETWORK DIAGRAM
FROM THE CALIBRATION DIALOG BOX
CLICK THE "MAXIMUM" BUTTON
CLICK MENU ITEM "CONTROLLER"
AND THEN CLICK "CALIBRATE"
MAXIMUM
AIR
BALANCE
ENTER MEASURED FLOW IN CFM
AND THEN CLICK CALIBRATE
STABLE
FLOW
REACHED
?
NO
YES
START
A
Andere Handbücher für Excel 10
3
Inhaltsverzeichnis
Andere Honeywell Controller Handbücher
Honeywell
Honeywell DC1000 SERIES Bedienungsanleitung
Honeywell
Honeywell ML6131 Bedienungsanleitung
Honeywell
Honeywell AutoRAE 2 Bedienungsanleitung
Honeywell
Honeywell ML6284 Bedienungsanleitung
Honeywell
Honeywell UDC100 Bedienungsanleitung
Honeywell
Honeywell HC900 Bedienungsanleitung
Honeywell
Honeywell ControlEdge 900R04-0200 Bedienungsanleitung
Honeywell
Honeywell CN100 Technisches Handbuch
Honeywell
Honeywell CentraLine EAGLEHAWK NX Bedienungsanleitung
Honeywell
Honeywell R7515C MacroCel Bedienungsanleitung
Honeywell
Honeywell THR0924 Bedienungsanleitung
Honeywell
Honeywell Lyric Produktinformationsblatt
Honeywell
Honeywell ControlEdge 900 platform Technisches Handbuch
Honeywell
Honeywell V4055A Bedienungsanleitung
Honeywell
Honeywell UDC3500 Montage- und Bedienungsanleitung
Honeywell
Honeywell HercuLink Bedienungsanleitung
Honeywell
Honeywell V7335A 2000 Series Bedienungsanleitung
Honeywell
Honeywell VMM Series Bedienungsanleitung
Honeywell
Honeywell CIPer 50 Installations- und Betriebshandbuch
Honeywell
Honeywell SUPER TRADELINE S8610U Bedienungsanleitung
