Honeywell PRO 2000 Series Betriebsanleitung



To program the controller, perform the following procedures in the order listed:

   

Fig. 1 Program Menu

Press the MENU button, then select PROGRAM and press the button to view the

program menu.

  !

Fig. 2

1. From the menu, use the and buttons to highlight RELAY 1.

2. Press the button to select RELAY 1 to view the parameters. Fig. 2 shows

RELAY 1.

 "#

Fig. Program - Setpoint

1. From the menu, use the and buttons to highlight SETPOINT.

2. Press the button to display the setpoint value.

3. Use the and buttons to increase/decrease the desired setpoint

temperature.

Set the temperature to 45° F.

4. Press the button to accept the setpoint temperature and display the next

option.

Honeywell Series 2000

 $"%%&#"'"#(

Fig. Program – Differential

1. From the menu, use the and buttons to highlight DIFFERNTL.

2. Press the button to display the differential value.

3. Use the and buttons to increase/decrease the desired value.

Set the value to 3° F.

4. Press the button to accept the value and display the next option.

 )#&

Fig. Program – Sensor

1. From the menu, use the and buttons to highlight SENSOR.

2. Press the button to display the sensor selections.

3. Use the and buttons to select Sensor A or B.

Select sensor A.

4. Press the button to accept the highlighted sensor and display the next option.

 *+,'

Fig. Program Heat/Cool

1. From the menu, use the and buttons to highlight HEAT/COOL (Default:

HEAT).

2. Press the button to display the heat and cool selections.

3. Use the and buttons to select Heat or Cool.

Select COOL.

4. Press the button to accept the highlighted selection and display the next

option.

____________________________________________________________________



    

 - 

Fig. Program – Exit

Press the EXITbutton to finish the programming for Relay 1.

Press the HOME button to leave programming mode and return to the home screen.

This completes the programming procedure for Cooling Only System.



 



To program the controller for time delay, perform the following procedures in the

order listed:

  



To access the Setup menu, press and hold the MENU button for five seconds. See

Fig. 1.

! 

When you are working with the menus, use the:

•Left arrow button ( ) to scroll backward through the menus

•Right arrow button () to select the highlighted menu item and display

its content

•Up and Down arrow buttons (and ) to scroll up and down through a

list of items or to increase or decrease the value of a displayed parameter

NOTE: If you press the HOME

button or there is no keypad activity for four

Minutes, you exit Program mode and return to the home screen.

If you press the MENU button, you exit and return to the menu.









  

To go from Setup menu screen as shown in Fig. 1 to Min Off screen shown in Fig. 2,

follow the steps as listed below:

1. From the Setup menu (Fig. 1), use the Down arrow button () to highlight

OUTPUTS.

2. Press Right arrow button () to display the Outputs menu.

3. Press the Down arrow button () to highlight OPTIONS.

4. Press Right arrow button () to display the Options menu.

5. Press the Down arrow button () to highlight MIN OFF.

6. Press Right arrow button () to display the Min Off screen (Fig. 2).

" #$%&&'(

This is the minimum number of seconds of “off time” for all relays.

Use the Up and Down arrow buttons (and ) to increase/decrease the desired

number of seconds from 0 to 990 in 10 second increments.

Default: 0 (zero)

Range: 0 to 990 seconds

Aqua Air factory setting: 20 seconds

)*+

After entering the desired number of seconds, press HOME button to accept the seconds

and finish the programming process. The display should show Home screen.

_____________________________________________________________________

Andere Handbücher für PRO 2000 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Controller Handbücher

Honeywell

Honeywell T775A Bedienungsanleitung

Honeywell

Honeywell Z74S-AN Bedienungsanleitung

Honeywell

Honeywell S9360A Bedienungsanleitung

Honeywell

Honeywell W7340 Bedienungsanleitung

Honeywell

Honeywell VaporStat L408J Bedienungsanleitung

Honeywell

Honeywell Lyric Bedienungsanleitung

Honeywell

Honeywell MS7503A2023 Bedienungsanleitung

Honeywell

Honeywell C Bedienungsanleitung

Honeywell

Honeywell CP-UL1012S Bedienungsanleitung

Honeywell

Honeywell UDC2500 Bedienungsanleitung

Honeywell

Honeywell EVOTOUCH CONTROLLER Bedienungsanleitung

Honeywell

Honeywell HC900 Bedienungsanleitung

Honeywell

Honeywell 5000 Series Bedienungsanleitung

Honeywell

Honeywell ML7999C Bedienungsanleitung

Honeywell

Honeywell Excel 800 Installations- und Betriebshandbuch

Honeywell

Honeywell ATC928G3000 Bedienungsanleitung

Honeywell

Honeywell ALERTON VIP-363-HOA Bedienungsanleitung

Honeywell

Honeywell CENTRA LINE MERLIN N Series Bedienungsanleitung

Honeywell

Honeywell J48 Bedienungsanleitung

Honeywell

Honeywell Aquastat L8100C Bedienungsanleitung

Honeywell

Honeywell Stryker VAV Bedienungsanleitung

Honeywell

Honeywell MT4-024 Bedienungsanleitung

Honeywell

Honeywell Aquastat L7224U Bedienungsanleitung

Honeywell

Honeywell Excel 10 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung