Honeywell GENT Mimic LED Driver Card Gebrauchsanweisung

These instructions cover the Mimic LED Driver

Card (S4-34600) and Connection converter

(S4-34494), which are designed to be used in

Custom panels.

The Mimic LED Driver connects to a Master Repeat

Card which in turn connects to a loop circuit of a

Vigilon fire system. Each Mimic LED Driver Card

can control up to 768 LEDs and this leaflet covers

the connection of up to 2 Mimic LED Driver Cards.

The Connector converters that holds the terminals

for wiring LEDs.

Custom Panel

LED selection

Only use high efficiency Red,Amber or Green

LEDs with a Mimic LED Driver Card.

"Do not use Blue or White LEDs as these are

not suitable for use with the Mimic LED Driver Card.

Compatibility

The Mimic LED Driver Cards are compatible for use

in Vigilon system where the Control panel has

specific MCC/MCB software, see technical data

section. The Master Repeat Card is configured

using the Mimic Configuration Tool.

4188-951_issue 2_01/12_Part 1_Mimic LED driver 1

Data and Installation

Mimic LED Driver Card

S4-34600 & S4-34494

by Honeywell

S4-34600

Mimic LED Driver Card

S4-34494

Connection Converter

26-way

300mm ribbon cable

20-way

200mm Flat flexible cable

01 L1 02 L2

0C LC P9

P17

DANGER

BT+ BT-

RS485 0V 24V

WRITE PROTECT

BUZZER

DISABLE

DANGER

DO NOT

REMOVE

L N

FS2

FS4

P16

SW3

PB2

WD1

P14

USB

FS3

2A(QB)

RESET

Mimic Repeat Card

ADDRESS

BOARD

UPSIDEDOWN

ROTATE

P16P15P14P13P12P11

OUT

Mimic

LED Driver

Card 2

WARNING

Removal of

cover exposes

live parts

DANGER

ADDRESS

BOARD

UPSIDEDOWN

ROTATE

P16P15P14P13P12P11

OUT

Mimic

LED Driver

Card 1

Connector

Converter 6

Connector

Converter 1

LED Bank 1 (768 LEDs)LED Bank 2 (768 LEDs)

24610812 14 16 18 20 22 26

1359711 13 15 17 19 21 25

24610812 14 16 18 20 22 26

1359711 13 15 17 19 21 25

24610812 14 16 18 20 22 26

1359711 13 15 17 19 21 25

24610812 14 16 18 20 22 26

1359711 13 15 17 19 21 25

Maximum of up to

1536 LEDs can be

controlled with

2 Mimic LED Driver

Cards

01 L1 02 L2

0C LC P9

P16

Custom Panel

Backbox

Door

20 way

cable

26 way

cable

Vigilon device loop To mains fused spur unit

Address

No link fitted

One link fitted

*No links are fitted here

for this application.

Links set LED

board orientation.

Mounting

It is recommended that the Mimic LED Driver Cards are mounted inside a Custom panel using suitable PCB

standoffs, there are 6-3mm PCB fixing holes provided on the card. The Connection converters are mounted

on 35mm DIN rails. The LEDs and associated wiring must also be contained inside the same enclosure for

mechanical protection.

"The designer of the Custom panel in which the Mimic LED Driver Cards,Connection converters and LEDs are

mounted must ensure the panel enclosure is EMC compliant and is CE marked.

Cables

The internal connection from the Connection converter to each LED inside the Custom panel is made using

a standard PVC cable. Each LED can be positioned a maximum of up to 3m cable distance away from the

terminals of a Connection Converter.

For recommendations on loop cable type refer to the manual supplied with the Vigilon control panel.

Earth

The Custom panel must be earthed. The loop cable screen must be continued through the Custom panel,

whether the earth is connected to the Custom panel or not.

Do not use any part of building structure for earthing.

Mains supply

The mains supply to the Custom panel must be via an unswitched 5A fused spur unit. A disconnect device

must be provided to disconnect both poles and must have a minimum gap of 3mm. The disconnect device

should be available as part of the building installation and must be easily accessible after installation is

complete.

Before removal of any card or disconnection of any cable from the Custom panel ensure both mains and battery supplies

are disconnected.

Battery supply

Data and Installation Mimic LED Driver Card

2 4188-951_issue 2_01/12_Part 1_Mimic LED driver

FS2

3.15A(T)

Ceramic

(Anti Surge)

Battery Fuse

BT+ BT-

RS485 0V 24V

BUZZER

DISABLE

DANGER

DO NOT

REMOVE

FS2

SW3

PB2

WD1

P14

USB

FS3

2A(QB)

DANGER

WARNING

Removal of

cover exposes

live parts.

Master Repeat Card

Black

Red

Battery lead

Link lead

6V 7Ah Battery

Leave the final connection of the battery for the Servicing organisation.

This connection is made during power up and commissioning.

You can use 1 - 12V 7Ah battery (VSRPT-BATT)

or 2 - 6V 7AH batteries as shown.(VSRPT-BATT-A3)

To connect multiple Mimic LED Driver Cards

You can daisy chain up to two Mimic LED driver cards to the Master Repeat Card using the 20 way flat

flexible cable .

How to connect a flat flexible cable

Hold the locking tab by the edges and lift it upwards a little jand insert the flat flexible cable kinto the

socket. Ensure the cable contacts are on the opposite side to the locking tab. Push down the locking tab l

to lock the flat flexible cable.

How to disconnect a flat flexible cable

Hold the locking tab by the edges at positions mand lift it upwards one side at a time nto disengage the flat

flexible cable. Then remove the cable ofrom the socket.

To connect the ribbon cables from Mimic LED Driver card to Connection converters

Connect one end of the 26 way ribbon cable to the IDC header on the Mimic LED Driver card (P11) and

the other end to a Connection converter. The Mimic LED Driver card can accommodate up to6-26way

ribbon cable for wiring LEDs via 6 Connection converters.

4188-951_issue 2_01/12_Part 1_Mimic LED driver 3

Mimic LED Driver Card Data and Installation

P13

OUT

Master Repeat Card

OUT

Mimic LED Driver

Card 1

To connect a flat flexible cable

P13

To disconnect a flat flexible cable

Mimic LED Driver

Card 2

B B

24610812 14 16 18 20 22 26

1359711 13 15 17 19 21 25

Connector

Converter 1

P16P15

P14

P13

P12P11

Mimic LED Driver Card

26 way ribbon cable

24610812 14 16 18 20 22 26

1359711 13 15 17 19 21 25

Connector

Converter 2

24610812 14 16 18 20 22 26

1359711 13 15 17 19 21 25

26 way ribbon

cables

Connector

Converter 6

Connection to 128 LEDsConnection to 128 LEDsConnection to 128 LEDs

Relationship between Terminals and external LEDs

Technical data

S4-34600 Mimic LED Driver Card

Dimensions 160mm height x 150mm width x 30mm depth

Card weight 150g

Storage temperature -30ºC to +70ºC

Operating temperature -10ºC to +60ºC

Relative Humidity Up to 95% - Temperature +5ºC to +45°C (Non condensing)

LED output per

Mimic LED Driver Card

Up to 768 high efficiency LEDs can be driven by a Mimic LED Driver Card

Each LED can be 3m cable distance away from the Connection converter.

Use only high efficiency Red,Amber or Green LEDs.

Vigilon Panel

compatibility

Fully compatible with LPC = V3.93 / V4.35 & MCC/MCB = V3.94 / V4.37.

Data and Installation Mimic LED Driver Card

Gent by Honeywell reserves the right to revise this publication from time to time and make changes to the content hereof without

obligation to notify any person of such revisions of changes.

Hamilton Industrial Park, Waterside Road, Leicester LE5 1TN, UK Website: www.gent.co.uk

Telephone: +44 (0) 116 246 2000 Technical support: www.gentexpert.co.uk Fax (UK): +44 (0)116 246 2300

4 4188-951_issue 2_01/12_Part 1_Mimic LED driver

by Honeywell

Do not dispose of with your normal household waste.

Do not burn.

WEEE Directive:

At the end of their useful life, the packaging,

product and batteries should be

disposed of via a suitable recycling centre.

At the end of their useful life, the packaging,

product and batteries should be disposed of

via a suitable recycling centre and in

accordance with national or local legislation.

24610

812 14 16 18 20 22 26

1359

11 13 15 17 19 21 25

LED

Ref +-

LED

Ref +-

LED

Ref +-

LED

Ref +-

LED

Ref +-

LED

Ref +-

LED

Ref +-

LED

Ref +-

126 8925 817 24 825 23 833 22 841 21 849 20 857 19 8

226 710 25 718 24 726 23 734 22 742 21 750 20 758 19 7

326 611 25 619 24 627 23 635 22 643 21 651 20 659 19 6

426 512 25 520 24 528 23 536 22 544 21 552 20 560 19 5

526 413 25 421 24 429 23 437 22 445 21 453 20 461 19 4

626 314 25 322 24 330 23 338 22 346 21 354 20 362 19 3

726 215 25 223 24 231 23 239 22 247 21 255 20 263 19 2

826 116 25 124 24 132 23 140 22 148 21 156 20 164 19 1

65 18 873 17 881 16 889 15 897 14 8105 13 8113 12 8121 11 8

66 18 774 17 782 16 790 15 798 14 7106 13 7114 12 7122 11 7

67 18 675 17 683 16 691 15 699 14 6107 13 6115 12 6123 11 6

68 18 576 17 584 16 592 15 5100 14 5108 13 5116 12 5124 11 5

69 18 477 17 485 16 493 15 4101 14 4109 13 4117 12 4125 11 4

70 18 378 17 386 16 394 15 3102 14 3110 13 3118 12 3126 11 3

71 18 279 17 287 16 295 15 2103 14 2111 13 2119 12 2127 11 2

72 18 180 17 188 16 196 15 1104 14 1112 13 1120 12 1128 11 1

Terminal numbers on a

Connection converter

LED Ref 1

Connection Converter

LED Ref 34

The illumination of LEDs connected to the Connection Converters of a Mimic LED Driver Card is

determined by the configuration held at the Master Repeat Card (MRC).

The following information show how to load a LED Driver template file and associate LED shapes with

terminals of Connection converter and configure each LED shape with a system event using the Mimic

Configuration tool.

How to load the 'Mimic LED Driver template.s19' file

The Master Repeat Card is configured using the Mimic Configuration Tool. The tool requires an 'LED

Driver template' file to be loaded to configure a Mimic LED Driver Card connected to the MRC. To open

the template file follow steps jto m.

How Mimic LED ‘Shapes’ relate to the Mimic LED Driver Card and Terminals

The 'LED Driver template' file has defined LED shapes of each possible LED that can be connected to the

Connection converters associated with a Mimic LED Driver Card.

4188-951_issue 2_01/12_Part 2_Mimic LED driver 1

Commissioning information

Mimic LED Driver Card

S4-34600 & S4-34494

by Honeywell

Do not alter these settings as they are

pre defined in the LED Driver template file.

7 P16_24_8

Shape number 7

Related to IDC Connector P16

on the Mimic LED Driver Card

IDC connector P16 is ribbon

cabled to Connection connector

and its terminals:

Terminal 24 is + LED

Terminal 8 is - LED

When the linked function is active

you can define the LED action to:

P13

Master Repeat Card

OUT

Mimic LED Driver

Card 1

P15

P13

P14

P11

P12

Connection

converter 1

Connection

converter 6

Address

24610

812 14 16 18 20 22 26

1359

711 13 15 17 19 21 25

Connection Converter

P16

From the directory

select ‘ ’

to load the configuration template

for the .

DataFiles

LED Driver card 1

LED Driver template.s19

If two LED Driver Cards are fitted inside

a Custom panel, both daisy chain

connected to a ,

then you will need another

Master Repeat Card

LED Driver

template file.

How to link Mimic LED ‘Shapes’ to system events

Each used LED shape must be linked with a system event, such as:

¨Device fire

¨Device fault

¨Channel fire

¨Channel fault

¨Zone fire

¨Zone fault

¨Card fire

¨Card fault or

¨Supervisory Command Build.

Below is a typical example that shows how a shape can be linked to a zone:

For full information on configuration see the instructions supplied with the Mimic Configuration tool.

Test

Test the Custom panel and ensure it gives the correct indication for the configured Vigilon System event.

Commissioning information Mimic LED Driver Card

Gent by Honeywell reserves the right to revise this publication from time to time and make changes to the content hereof without

obligation to notify any person of such revisions of changes.

Hamilton Industrial Park, Waterside Road, Leicester LE5 1TN, UK Website: www.gent.co.uk

Telephone +44 (0) 116 246 2000 Fax (UK): +44 (0)116 246 2300

2 4188-951_issue 2_01/12_Part 2_Mimic LED driver

by Honeywell

Drag and drop an LED ‘Shape’ onto the

a system event in the system tree. This

example shows being dropped

onto so the two are linked.

Shape 5

Zone 5,

The LED Shape here is linked to

So when has a fire event then the LED connected

to terminals and will be lit (On).

Note also the is associated with

IDC Connector on the

5 P16_26_8

Zone 5 - Fire

Zone 5

26 8

P16

Connection Converter

Mimic LED Driver Card.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Controller Handbücher

Honeywell

Honeywell ZG 215N Bedienungsanleitung

Honeywell

Honeywell J48 Bedienungsanleitung

Honeywell

Honeywell ML6275 Bedienungsanleitung

Honeywell

Honeywell V8200 Bedienungsanleitung

Honeywell

Honeywell 10260A Series Leitfaden

Honeywell

Honeywell HUPF Series Bedienungsanleitung

Honeywell

Honeywell S8600B Bedienungsanleitung

Honeywell

Honeywell M6410A Bedienungsanleitung

Honeywell

Honeywell UDC3500 Bedienungsanleitung

Honeywell

Honeywell UDC2500 Bedienungsanleitung

Honeywell

Honeywell VK41 V Series Bedienungsanleitung

Honeywell

Honeywell AQS51-KAM Bedienungsanleitung

Honeywell

Honeywell VR8215S Bedienungsanleitung

Honeywell

Honeywell HON 5020 Betriebsanleitung

Honeywell

Honeywell SW2 Bedienungsanleitung

Honeywell

Honeywell ML7420A6025T Bedienungsanleitung

Honeywell

Honeywell SDW 30 Bedienungsanleitung

Honeywell

Honeywell Unipoint 2306B1000 Bedienungsanleitung

Honeywell

Honeywell MN7505 Bedienungsanleitung

Honeywell

Honeywell L4188 Bedienungsanleitung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Honeywell

Honeywell Excel 10 W7751H Bedienungsanleitung

Honeywell

Honeywell VCA Series Bedienungsanleitung

Honeywell

Honeywell PRO 2000 Series Betriebsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch